大灰厂断层形变测量结果的地质解译

对大灰厂断层形变测点的36年基线、水准观测资料进行了系统研究，将观测值的变化转换为断层的水平和垂直活动量，并从断层活动方式与所受压应力方向的关系研究了华北地区邢台一唐山地震时段和大同一张北地震时段，以及在八宝山断裂(大灰厂段)上显示的地震前后断层异常活动特征及相应的应力状态。认为对跨断层形变测量资料的分析研究不仅要通过一定的数学处理和统计学分析，更应当从断层活动方式及应力状态进行地质解译，以探索孕震过程中的断层活动信息。     

汤东活动断裂带土壤H2、Rn地球化学特征

为研究汤东断裂带土壤气体地球化学特征及其所反映的构造地球化学背景, 采用野外监测的方法分析了张河村与邢李庄村两条测线的土壤H₂、 Rn分布特征。 结果表明, 张河村H₂浓度、 Rn活度浓度的分布范围分别为0.24×10^-6～174.7×10^-6、 13.3～69.8 kBq·m^-3, 背景值分别为14.26×10^-6, 24.8 kBq·m^-3。 邢李庄测线H₂浓度、 Rn活度浓度的分布范围11.8×10^-6～67.06×10^-6、 43.6～72.6 kBq·m^-3, 背景值分别为37.13×10^-6、 72.6 kBq·m^-3。 张河村测线在90～105 m处, H₂、 Rn出现强烈高值异常, 而120～150 m处出现高值异常。 异常值位于断裂带附近, H₂、 Rn气体测值对断裂位置具有良好的指示作用。 气体异常主要受汤东活动断裂构造控制, 汤东断裂下方的深大断裂和汤阴地堑中下地壳的低速体对深部气体释放有重要作用。     

隐伏正断层错动致地表破裂变形特征的研究

通过建立三维计算模型,对隐伏正断层在均匀错动、倾斜错动和翘倾错动方式下地表土体的应力路径、破裂和变形特征进行了研究。根据地表破裂临界值,分析了工程建设“避让带”的宽度和起始位置的变化特征。根据行业规范,提出工程建设“关注带”的确定方法,分析了“关注带”的宽度和起始位置的变化特征,得到以下主要结论:①在断层错动过程中,位于两侧的地表土体应力路径变化明显不同,下盘一侧和上盘一侧分别以三轴拉伸和三轴压缩为主;②地表强变形带与地表破裂带的分布并不一致,需要综合考虑等效塑性应变和总位移比2个指标来评价同震地表错动对建筑物的影响;③当隐伏断层错动的垂直位移达到3m时,工程建设“避让带”的宽度在10—90m范围内变化,受上覆土体厚度和断层倾角的影响最大,而工程建设“关注带”的宽度在150—400m范围内变化,受上覆土体的性质影响最大。     

嫩江断裂带北段的第四纪活动特征初步研究

嫩江断裂带是松辽盆地的西边界断裂,但受第四系强覆盖等研究条件的限制,前人对该断裂第四纪构造活动的研究较少。本文针对该断裂带北段开展了野外地质调查,并综合大地电磁测深和纵波速度结构等结果,初步研究了嫩江断裂带北段的第四纪活动特征。调查发现,该断裂北段主要发育地貌陡坎、基岩滑坡、地层揉皱变形、近垂直擦痕、基岩崩塌与线性断塞塘等特征。探槽古地震研究揭示断裂带北段在（80.9±4.6）—（62.9±2.3）ka BP曾发生1次古地震事件,运动方式为正断,垂直位移量约1.5m,震级约为M_S 7.1—7.3,断裂在晚更新世曾发生过强烈活动。研究结果有助于认识了解该断裂和松辽盆地的第四纪构造变形过程,并为评价该断裂及邻区的地震活动潜势提供参考。     

SH波水平入射穿越垂直断层隧道动力响应分析

结合黏弹性人工边界的时域波动输入方法和显式有限元法,设计了含垂直断层三维场地的SH波输入方法。基于建立的输入方法,研究了垂直断层对隧道地震响应的影响,并通过自由场算例验证了该方法具有较好精度。数值模拟结果表明:对于断层迎波侧的隧道结构,断层会对其地震动响应产生显著的放大作用,对于断层逆波侧的隧道结构,断层会对其产生隔离地震动的作用;相对周围围岩,断层介质的剪切波速越小,其产生的放大效应和隔震效果也会越显著;断层宽度越小,其对隧道地震动响应的影响范围也就越小,但是断层宽度的变化对于断层两侧隧道的地震动响应的影响并不明显。     

THE ACTIVITY OF WESTERN LISHAN FAULT SINCE THE LATE PLEISTOCENE

Along the northern piedmont of Mt. Lishan, the characteristics and locations of the active normal Lishan fault in west of Huaqing Pool provide important evidences for determining the seismotectonic environment, seismic stability evaluation of engineering in the eastern Weihe Basin. After reviewing the results from high-density resistivity method, seismic profile data, geological drillhole section and trenching in west of the Huaqing Pool, it is found that the strike of western normal Lishan Fault changes from EW direction at the eastern part to the direction of N60°W, and the fault consists of two branches, dipping NE with a high dip angle of~75°. The artificial shallow seismic profile data reveals that the attitude of strata near Lishan Fault mainly dips to south, which is presumed to be related to the southward tilt movement of Mt. Lishan since the Cenozoic. The section of geological drillhole reveals that since the late middle Pleistocene, the displacement of the paleo-soil layer S₂ is about 10m. And the maximum displacement of western Lishan Fault recorded in the paleo-soil layer S₁ reaches 7.8m since the late Pleistocene. In addition, evidences from trench profile show that the western Lishan Fault was active at least 3 times since Malan loess deposition with ¹⁴ C dating age(32 170±530)Cal a BP. The multiple activities of the Lishan Fault result in a total displacement about 3.0m in the Malan loess layer L₁. The latest activity of the western Lishan Fault produced a displacement of about 0.9m in the early Holocene loess layer L₀((8 630±20)Cal a BP)and caused obvious tensile cracks in the Holocene dark leoss layer S₀((4 390±20)Cal a BP). Briefly, we have obtained a vertical movement rate of about 0.11~0.19mm/a since the Holocene((8 630±20)Cal a BP)in the western extension of the Lishan Fault, the recurrence interval of earthquakes on the fault is about(10.7±0.5)ka, and the co-seismic surface rupture in a single event is inferred to be about 0.9m.     

SLIP OFFSET ALONG STRIKE-SLIP FAULT DETERMINED FROM STREAM TERRACES FORMATION

Slip rate is one of the most important parameters in quantitative research of active faults. It is an average rate of fault dislocation during a particular period, which can reflect the strain energy accumulation rate of a fault. Thus it is often directly used in the evaluation of seismic hazard. Tectonic activities significantly influence regional geomorphic characteristics. Therefore, river evolution characteristics can be used to study tectonic activities characteristics, which is a relatively reliable method to determine slip rate of fault. Based on the study of the river geomorphology evolution process model and considering the influence of topographic and geomorphic factors, this paper established the river terrace dislocation model and put forward that the accurate measurement of the displacement caused by the fault should focus on the erosion of the terrace caused by river migration under the influence of topography. Through the analysis of the different cases in detail, it was found that the evolution of rivers is often affected by the topography, and rivers tend to migrate to the lower side of the terrain and erode the terraces on this side. However, terraces on the higher side of the terrain can usually be preserved, and the displacement caused by faulting can be accumulated relatively completely. Though it is reliable to calculate the slip rate of faults through the terrace dislocation on this side, a detailed analysis should be carried out in the field in order to select the appropriate terraces to measure the displacement under the comprehensive effects of topography, landform and other factors, if the terraces on both sides of the river are preserved. In order to obtain the results more objectively, we used Monte Carlo method to estimate the fault displacement and displacement error range. We used the linear equation to fit the position of terrace scarps and faults, and then calculate the terrace displacement. After 100, 000 times of simulation, the fault displacement and its error range could be obtained with 95%confidence interval. We selected the Gaoyan River in the eastern Altyn Tagh Fault as the research object, and used the unmanned air vehicle aerial photography technology to obtain the high-resolution DEM of this area. Based on the terrace evolution model proposed in this paper, we analyzed the terrace evolution with the detailed interpretation of the topography and landform of the DEM, and inferred that the right bank of the river was higher than the left bank, which led to the continuous erosion of the river to the left bank, while the terraces on the right bank were preserved. In addition, four stages of fault displacements and their error ranges were obtained by Monte Carlo method. By integrating the dating results of previous researches in this area, we got the fault slip rate of(1.80±0.51)mm/a. After comparing this result with the slip rates of each section of Altyn Tagh Fault studied by predecessors, it was found that the slip rate obtained in this paper is in line with the variation trend of the slip rate summarized by predecessors, namely, the slip rate gradually decreases from west to east, from 10~12mm/a in the middle section to about 2mm/a at the end.     

RELOCATION OF THE 23 NOVEMBER 2017 WULONG MS5.0 EARTHQUAKE SEQUENCE AND ANALYSIS OF ITS SEISMOGENIC FAULT

The Wulong M_S5.0 earthquake on 23 November 2017, located in the Wolong sap between Wenfu, Furong and Mawu faults, is the biggest instrumentally recorded earthquake in the southeastern Chongqing. It occurred unexpectedly in a weak earthquake background with no knowledge of dramatically active faults. The complete earthquake sequences offered a significant source information example for focal mechanism solution, seismotectonics and seismogenic mechanism, which is helpful for the estimation of potential seismic sources and level of the future seismic risk in the region. In this study, we firstly calculated the focal mechanism solutions of the main shock using CAP waveform inversion method and then relocated the main shock and aftershocks by the method of double-difference algorithm. Secondly, we determined the seismogenic fault responsible for the M_S5.0 Wulong earthquake based on these calculated results. Finally, we explored the seismogenic mechanism of the Wulong earthquake and future potential seismic risk level of the region. The results show the parameters of the focal mechanism solution, which are:strike24°, dip 16°, and rake -108° for the nodal plane Ⅰ, and strike223°, dip 75°, and rake -85° for the nodal plane Ⅱ. The calculations are supported by the results of different agencies and other methods. Additionally, the relocated results show that the Wulong M_S5.0 earthquake sequence is within a rectangular strip with 4.7km in length and 2.4km in width, which is approximately consistent with the scales by empirical relationship of Wells and Coppersmith(1994). Most of the relocated aftershocks are distributed in the southwest of the mainshock. The NW-SE cross sections show that the predominant focal depth is 5~8km. The earthquake sequences suggest the occurrence features of the fault that dips northwest with dip angle of 63° by the least square method, which is largely consistent with nodal planeⅡof the focal mechanism solution. Coincidentally, the field outcrop survey results show that the Wenfu Fault is a normal fault striking southwest and dipping 60°~73° by previous studies. According to the above data, we infer that the Wenfu Fault is the seismogenic structure responsible for Wulong M_S5.0 earthquake. We also propose two preliminary genetic mechanisms of "local stress adjustment" and "fluid activation effect". The "local stress adjustment" model is that several strong earthquakes in Sichuan, such as M8.0 Wenchuan earthquake, M7.0 Luzhou earthquake and M7.0 Jiuzhaigou earthquake, have changed the stress regime of the eastern margin of the Sichuan Basin by stress transference. Within the changed stress regime, a minor local stress adjustment has the possibility of making a notable earthquake event. In contract, the "fluid activation effect" model is mainly supported by the three evidences as follows:1)the maximum principle stress axial azimuth is against the regional stress field, which reflects NWW-SEE direction thrusting type; 2)the Wujiang River crosscuts the pre-existing Wenfu normal fault and offers the fluid source; and 3)fractures along the Wenfu Fault formed by karst dissolution offer the important fluid flow channels.     

青藏高原东南缘地貌边界性质的界定及其对高原东南缘扩展模式的启示

青藏高原东南部的地貌结构是高原隆升深部动力过程与高原扩展的重要指标之一,存在受下地壳流驱动的渐变模型和受宽约50～200km的雅砻-玉龙断裂系控制的陡变模型2种不同认识。文中基于30m分辨率的SRTM数据进行数字高程分析,利用高程和水系参数对研究区地貌加以提取和分析,结合野外地貌和构造调研的结果以及前人的相关研究,对高原东南缘川滇地块中部构造地貌细结构进行了详细的解析。研究认为,青藏高原东南边界具有明显的台阶式构造地貌结构,不同台阶梯度带受不同时期发育的NE-SW向断裂控制。其中一级边界位于木里-玉龙断裂,控制了平均海拔4 200m的高原面的东南边界,是渐新世—中新世早期构造抬升的结果;二级边界受中新世中期逆冲活动的金河-箐河断裂控制,其构成丽江—盐源一带海拔中等(约3 000m)、相对低起伏区域的东南边界。高原东南边界的台阶式构造地貌结构反映了高原向SE的前展式逆冲扩展。这种扩展模式并不支持下地壳管道流连续变形模型。     

利用地面激光与地质雷达综合探测活断层浅层三维结构——以川西理塘毛垭坝盆地北缘正断层为例

快速获取活断层的高精度微地貌形态和对应的浅层三维结构是揭示活断层浅地表形迹与活动特征的关键。文中综合利用地面三维激光扫描仪和地质雷达技术,以川西理塘地区毛垭坝盆地北缘主边界断裂禾尼段的正断层崖为研究对象,获取了该处正断层错动2期最新地貌面的精确地表垂直位移量和浅层二维地质雷达图像,并初步建立了基于地面三维激光与地质雷达的活断层微地貌精细化三维测量方法,构建了断层崖微地貌的精细三维模型和浅表三维图像,揭示了正断层崖处发育的伸展地堑结构,同时初步实现了断层微地貌地表地下三维数据的一体化融合显示及相互解译。应用结果表明,该方法可以同时快速、高效、无损地获取大范围内的活断层微地貌及浅层结构的多层次、多视觉的空间数据,极大地提高了对活动断层微地貌形态与浅层结构进行快速调查与研究的精度和认识水平,也为更全面地认识和理解活断层的空间分布与变形特征、活动习性和多期古地震遗迹等提供重要的数据和方法支持。因此,对该方法的继续探索和完善,将显著提升和扩展其在活断层定量化和精细化研究中的实用性及应用前景。