A laboratory experiment to monitor the contact state of a fault by transmission waves

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.     

A way to synchronize models with seismic faults for earthquake forecasting: Insights from a simple stochastic model

Numerical models are starting to be used for determining the future behaviour of seismic faults and fault networks. Their final goal would be to forecast future large earthquakes. In order to use them for this task, it is necessary to synchronize each model with the current status of the actual fault or fault network it simulates (just as, for example, meteorologists synchronize their models with the atmosphere by incorporating current atmospheric data in them). However, lithospheric dynamics is largely unobservable: important parameters cannot (or can rarely) be measured in Nature. Earthquakes, though, provide indirect but measurable clues of the stress and strain status in the lithosphere, which should be helpful for the synchronization of the models.The rupture area is one of the measurable parameters of earthquakes. Here we explore how it can be used to at least synchronize fault models between themselves and forecast synthetic earthquakes. Our purpose here is to forecast synthetic earthquakes in a simple but stochastic (random) fault model. By imposing the rupture area of the synthetic earthquakes of this model on other models, the latter become partially synchronized with the first one. We use these partially synchronized models to successfully forecast most of the largest earthquakes generated by the first model. This forecasting strategy outperforms others that only take into account the earthquake series. Our results suggest that probably a good way to synchronize more detailed models with real faults is to force them to reproduce the sequence of previous earthquake ruptures on the faults. This hypothesis could be tested in the future with more detailed models and actual seismic data.     

Great earthquakes of variable magnitude at the Cascadia subduction zone

Comparison of histories of great earthquakes and accompanying tsunamis at eight coastal sites suggests plate-boundary ruptures of varying length, implying great earthquakes of variable magnitude at the Cascadia subduction zone. Inference of rupture length relies on degree of overlap on radiocarbon age ranges for earthquakes and tsunamis, and relative amounts of coseismic subsidence and heights of tsunamis. Written records of a tsunami in Japan provide the most conclusive evidence for rupture of much of the plate boundary during the earthquake of 26 January 1700. Cascadia stratigraphic evidence dating from about 1600 cal yr B.P., similar to that for the 1700 earthquake, implies a similarly long rupture with substantial subsidence and a high tsunami. Correlations are consistent with other long ruptures about 1350 cal yr B.P., 2500 cal yr B.P., 3400 cal yr B.P., 3800 cal yr B.P., 4400 cal yr B.P., and 4900 cal yr B.P. A rupture about 700-1100 cal yr B.P. was limited to the northern and central parts of the subduction zone, and a northern rupture about 2900 cal yr B.P. may have been similarly limited. Times of probable short ruptures in southern Cascadia include about 1100 cal yr B.P., 1700 cal yr B.P., 3200 cal yr B.P., 4200 cal yr B.P., 4600 cal yr B.P., and 4700 cal yr B.P. Rupture patterns suggest that the plate boundary in northern Cascadia usually breaks in long ruptures during the greatest earthquakes. Ruptures in southernmost Cascadia vary in length and recurrence intervals more than ruptures in northern Cascadia.     

Geological and geomorphological characteristics of landslides triggered by the 2004 Mid Niigta prefecture earthquake in Japan

The 2004 Mid Niigta prefecture earthquake (M_JMA 6.8) triggered more than one thousand landslides in the Miocene to Quaternary sedimentary rocks in Japan. The most common landslides were shallow disrupted landslides on steep slopes, which has been common in many previous disastrous earthquakes in the world. The Mid Niigta prefecture earthquake also triggered more than one hundred deep landslides, providing valuable information on the conditions for their occurrence. A field investigation and the interpretation of aerial photographs taken before and after the earthquake suggest that reactivation of existing landslides and undercutting of slopes are the most important factors for deep landslides to be triggered by earthquakes. In addition, planar sliding surfaces seem to be essential for the generation of catastrophic landslides triggered by this earthquake. Planar bedding–parallel sliding surfaces were formed at the boundary between the overlying permeable sandstone and underlying siltstone or along the bedding planes of alternating beds of sandstone and siltstone. Sliding surfaces along the slope-parallel oxidation front were formed in the area of black mudstone. New landslides (rockslide-avalanches) occurred with the sliding surfaces in a several-cm thick tuff interbedded in siltstone. One rockslide-avalanche occurred on a slope where buckling deformation preceded the earthquake. Gentle valley bottom sediments were mobilized in many locations, probably because they were saturated and partial liquefaction had occurred due to the earthquake shaking.     

Damage Survey of Water Supply Systems and Fragility Curve of PVC Water Pipelines in the Chi–Chi Taiwan Earthquake

Substantial damage to water supply systems, including water delivery pipelines, water treatment plants, reservoirs, and water storage tanks, was reported after the 1999 Chi–Chi Taiwan Earthquake. This paper first summarizes the damage survey and then presents the results of seismic fragility analysis for underground pipelines. Construction blueprints of the water delivery pipelines and repair work orders of 11 townships and cities in the disastrous area were digitized into a Geographical Information System (GIS) for analysis and assessment. With the aid of the GIS system, we found that PVC pipes made up 86% of water delivery pipelines while steel, cast iron, ductile iron, PE and others took the rest. Therefore, this paper focuses on the fragility analysis of PVC pipes. Three different methods were applied to derive the fragility relations between the PVC water pipes having nominal diameters (approximately inner diameters) greater than or equal to 65 mm and earthquake intensity parameters such as peak ground acceleration and peak ground velocity. The results were then examined with those of other countries. The discrepancy between our results and the empirical equation used by HAZUS, an earthquake loss estimation software developed by the Federal Emergency Management Agency was not significant.     

The 1786 earthquake-triggered landslide dam and subsequent dam-break flood on the Dadu River, southwestern China — Reply

A short reply to discussion by Chanson.     

岩石、土壤样品中210Po测定方法的研究

研究了以铜箔为镀片时,自沉积总α计数法定量测定岩石、土壤样品中210Po的最佳制源环境、同位素的干扰和去除、共存元素的允许量以及适宜的溶(熔)矿方法,同时研究了银、铜两种镀片的区别。试验发现,当盐酸浓度为2.0mol/L,恒温80℃,振荡频率为180次/min、振程20mm时,制源2.0h,210Po自镀回收率在99.6%～100.4%之间,210Po加入量与α净计数率线性相关系数为0.9999。放置衰变法可以消除212Bi和218Po等短半衰期核素对210Po测量产生的影响,Vc存在时其它共存元素不干扰测定。方法配合HNO3HFHClO4溶矿(对复杂试样酸溶后的不溶渣,再进行碱熔),全程回收率为99.5%～100.4%。     

"嫦娥"卫星绕月飞行轨道的激光测定法

依据地月激光测距的成功实践和对卫星激光定轨的基础研究,提出了用地面对嫦娥卫星作激光测距的方法,高精度地测定嫦娥卫星绕月飞行时的实时在轨位置,论述了多站激光定轨和单站激光定轨的解算数模。     

Rapid orbit determination of LEO satellites using IGS clock and ephemeris products

Different types of GPS clock and orbit data provided by the International GPS Service (IGS) have been used to assess the accuracy of rapid orbit determination for satellites in low Earth orbit (LEO) using spaceborne GPS measurements. To avoid the need for reference measurements from ground-based reference receivers, the analysis is based on an undifferenced processing of GPS code and carrier-phase measurements. Special attention is therefore given to the quality of GPS clock data that directly affects the resulting orbit determination accuracy. Interpolation of clock data from the available 15 min grid points is identified as a limiting factor in the use of IGS ultra-rapid ephemerides. Despite this restriction, a 10-cm orbit determination accuracy can be obtained with these products data as demonstrated for the GRACE-B spacecraft during selected data arcs between 2002 and 2004. This performance may be compared with a 5-cm orbit determination accuracy achievable with IGS rapid and final products using 5 min clock samples. For improved accuracy, high-rate (30 s) clock solutions are recommended that are presently only available from individual IGS centers. Likewise, a reduced latency and more frequent updates of IGS ultra-rapid ephemerides are desirable to meet the requirements of upcoming satellite missions for near real-time and precise orbit determination.