Multi‐objective optimal design of FLC driven hybrid mass damper for seismically excited structures

Structural vibration control using active or passive control strategy is a viable technology for enhancing structural functionality and safety against natural hazards such as strong earthquakes and high wind gusts. Both the active and passive control systems have their limitations. The passive control system has limited capability to control the structural response whereas the active control system depends on external power. The power requirement for active control of civil engineering structures is usually quite high. Thus, a hybrid control system is a viable solution to alleviate some of the limitations. In this paper a multi‐objective optimal design of a hybrid control system for seismically excited building structures has been proposed. A tuned mass damper (TMD) and an active mass driver (AMD) have been used as the passive and active control components of the hybrid control system, respectively. A fuzzy logic controller (FLC) has been used to drive the AMD as the FLC has inherent robustness and ability to handle the non‐linearities and uncertainties. The genetic algorithm has been used for the optimization of the control system. Peak acceleration and displacement responses non‐dimensionalized with respect to the uncontrolled peak acceleration and displacement responses, respectively, have been used as the two objectives of the multi‐objective optimization problem. The proposed design approach for an optimum hybrid mass damper (HMD) system, driven by FLC has been demonstrated with the help of a numerical example. It is shown that the optimum values of the design parameters of the hybrid control system can be determined without specifying the modes to be controlled. The proposed FLC driven HMD has been found to be very effective for vibration control of seismically excited buildings in comparison with the available results for the same example structure but with a different optimal absorber. Copyright © 2002 John Wiley & Sons, Ltd.     

A response‐based decoupling criterion for multiply‐supported secondary systems

It is often infeasible to carry out coupled analyses of multiply‐supported secondary systems for earthquake excitations. ‘Approximate’ decoupled analyses are then resorted to, unless the response errors due to those are significantly high. This study proposes a decoupling criterion to identify such cases where these errors are likely to be larger than an acceptable level. The proposed criterion is based on the errors in the primary system response due to decoupling and has been obtained by assuming (i) the input excitation to be an ideal white noise process, (ii) cross‐modal correlation to be negligible, and (iii) the combined system to be classically damped. It uses the modal properties of the undamped combined system, and therefore, a perturbation approach has been formulated to determine the combined system properties in case of light to moderately heavy secondary systems. A numerical study has been carried out to illustrate the accuracy achieved with the proposed perturbation formulation. The proposed decoupling criterion has been validated with the help of two example primary‐secondary systems and four example excitation processes. Copyright © 2002 John Wiley & Sons, Ltd.     

Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

Study of a semi‐active stiffness damper under various earthquake inputs

Semi‐active stiffness damper (SASD) is one of many semi‐active control systems with the capability to mitigate the dynamic response using only a small amount of external power. The system consists of a hydraulic damper connected to the bracing frame in a selected story unit. In this paper, study of a SASD in two building models of five‐stories under four benchmark earthquake records is reported. The purpose of this study is to evaluate the effectiveness of the control system against structure type and varying earthquake inputs. Various control laws are chosen to work with SASD, such as: resetting control, switching control, linear quadratic regulator (LQR) and modified LQR, and the results are compared with no control and passive control cases. Numerical results show that the use of a SASD is effective in reducing seismic responses. Control effectiveness is dependent on the type of structure and earthquake excitation. Passive control is less effective than other control cases as expected. Resetting control, switching control and LQR generally perform similarly in response reduction. While modified LQR is more efficient and robust compared with other control algorithms. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

Ground‐shaking mapping for a scenario earthquake considering effects of geological conditions: a case study for the 1995 Hyogo‐ken Nanbu,Japan earthquake

In order to examine the applicability of ground‐shaking mapping techniques to a near‐field earthquake, a peak ground velocity map of the 1995 Hyogo‐ken Nanbu, Japan earthquake computed from seismic zoning methods that consider the effects of geological conditions is compared with the actual observed intensity map. When computing the ground‐shaking map, the site amplification at each site is calculated in terms of the average shear‐wave velocity of the ground estimated from the corresponding geomorphological conditions. This map shows a relatively good agreement with the observed intensity map. However, the computations provide smaller values for certain disastrous areas of the earthquake, where the effects on ground motion of a deep, irregular underground structure have been reported. The effect of such structures on site response is examined implementing 2D FEM analyses, thereby being also incorporated into the method. Results considering the effect of the irregular underground structure show better agreement with the observed intensity map. Copyright © 2002 John Wiley & Sons, Ltd.     

张北地震区三维构造特征

地震层析成像结果揭示了张北地震区的构造特征。震源区周围分布有相交的北北西和北东向低速异常带。极震区正下方壳内存在高速异常的坚固体 ,其周围被多条低速异常带围限。区域构造具备了大量积累应变能和向高应力区传递应变能的孕震构造特征 ,北北西和北东向的隐伏断裂共同构成了区域的发震构造。该震区在中新生代以来有过多期岩浆活动 ,震中区周围分布有几个新第三纪的火山口。极震区米家沟附近火山的三维剖分图给出了该火山从地表到壳内 10km深度的速度图像 ,中新生代的火山岩浆活动对该区域孕震构造的形成起了重要作用。     

渤海湾盆地北部奥陶纪岩相古地理

渤海湾盆地北部主要包括黄骅坳陷、沧县隆起、冀中坳陷和下辽河坳陷,区内奥陶系厚 6 0 0～ 80 0m,主要由石灰岩和白云岩组成。下奥陶统分为冶里组和亮甲山组,中奥陶统分为下马家沟组、上马家沟组和峰峰组,上统缺失。其中下马家沟组、上马家沟组和峰峰组又进一步划分为下段和上段。早奥陶世冶里期和亮甲山期,本区以局限海环境为主,其内散布着一些潮坪和滩。中奥陶世,本区岩相古地理面貌变化旋回极为明显,下马家沟期早期潮坪广布,晚期以局限海为主;上马家沟期早期又是潮坪广布,晚期以开阔海为主;峰峰期早期潮坪广布,晚期又以开阔海为主。在奥陶纪,本区经历了 4个大的海侵-海退旋回,其中上马家沟期晚期是本区乃至整个华北地台的最大海侵期。     

西昆仑地区塔木MVT型铅锌矿床成矿作用和成矿物质来源探讨

MVT型铅锌矿是西昆仑地区重要的铅锌矿床类型之一.为了探明西昆仑地区该类型矿床的成矿作用过程和成矿物质来源,本文以塔木矿床为例,在野外调研基础上,进行了光片鉴定、铅硫同位素、稀士元素和成矿元素研究,得到矿石中方铅矿的δ34SCDT为-5.04‰～+3.67‰,反映出油田卤水与深层卤水的混合特征;由铅同位素分析结果计算出表面年龄为461～481 Ma(早于泥盆纪438～410 Ma);由稀土元素分析数据得出岩(矿)石/球粒陨石标准化分配模式图表明,成矿物质主要来自地层.因而判定主要成矿物质可能来源于前泥盆系地层.喜马拉雅期逆冲推覆构造作用所引发的大规模热卤水运移、循环过程,导致矿质的进一步富集、沉淀.