村镇滑移隔震建筑瞬时摩擦耗能的参数敏感性分析

给出了村镇滑移隔震建筑瞬时摩擦耗能的概念,并以此概念为响应指标。通过极差大小的对比,分析了该响应指标对刚度比、第二阶段刚度系数、隔震层屈服位移、隔震层摩擦系数、系统质量比和上部结构自振周期六个参数变化的敏感程度,阐述了上述系统参数对瞬时摩擦耗能这一响应指标的影响规律。研究表明:场地条件和地震动幅值大小对瞬时摩擦耗能均有显著影响;在所考虑的参数范围内,上部结构自振周期总是对瞬时摩擦耗能有较为显著的影响,摩擦系数对瞬时摩擦耗能的影响跟场地条件有关,Ⅰ类场地条件中摩擦系数对瞬时摩擦耗能影响不显著,而Ⅱ、Ⅲ和Ⅳ类场地条件中,摩擦系数对瞬时摩擦耗能的影响则非常显著;隔震层屈服位移、刚度比和第二阶段刚度系数总得来讲对瞬时摩擦耗能影响不显著,质量比对瞬时摩擦耗能影响居中。     

水利工程震害中土工结构低应力破坏实例分析

实际工程活动与低应力下土石料工程性质密切相关。总结了与低应力条件相关的工程活动,在总结分析以往地震中堤防和坝体滑坡案例的基础上,指出滑坡深度通常小于7 m,其上覆有效应力大多小于100 kPa。在对106组地震液化数据资料分析的基础上,指出地基液化大多发生在上覆有效应力低于100 kPa的低应力条件下。在目前的研究中,通常只关注中、高应力条件下土石料的工程性质。在应用中低应力区的土石料计算参数取值通常与中、高应力条件下获得的强度和变形参数一致,而高、低应力条件下土石料的强度和变形特性是不同的,这种计算参数取值方法的适用性存在疑虑。因此,研究低应力条件下土石料的工程性质,探讨数值计算中低应力条件下土石料计算参数的取值方法,具有重要的工程意义和科学价值。     

天山上地幔结构及其对壳内构造运动的作用

以深部地球物理资料为基础,介绍了天山地震带上地幔的基本结构,讨论了天山不同地区上地幔介质的动力学性质和可能的驱动机制。认为水平挤压形变是造成西天山和天山毗邻西昆仑附近区域上地幔岩石圈缩短和增厚的主要原因;而在中天山和东天山靠近准噶尔盆地南缘一带,除了板块运动造成的水平挤压力之外,上地幔热物质有可能上浮甚至侵入到地壳之中。它们与水平运动一样,对壳内脆性介质的构造活动起到非常重要的作用,特别是地壳底部莫霍面附近的低速滑脱层成为震源区深部构造的一个明显标志。此外,自从印度 亚洲大陆碰撞以来,天山部分地区固结冷却的山根有可能在多重挤压变形和小尺度热对流的共同作用下,脱离它们的原有的层位而沉入上地幔     

Metamorphic and structural evolution of the Early Proterozoic Puolankajärvi Formation, Finland – I. Structural and textural relations

The amphibolite facies Puolankajärvi Formation (PjF) occupies the western margin of the Early Proterozoic Kainuu Schist Belt (KSB) of northern Finland. The lower and middle parts of the PjF consist of turbiditic psammites and pelites and tempestitic semipelites. This report concentrates on the pelitic lithologies which include quartz–two-mica–plagioclase schists with variable amounts of garnet, staurolite, andalusite and biotite porphyroblasts as well as sillimanite and cordierite segregations. The KSB forms a major north–south-trending synclinorium between two Archaean blocks. It contains both autochthonous and allochthonous units and is cut by faults and shear zones. The PjF lies on the western side of the KSB and is probably allochthonous. The formation has undergone six major deformation phases (D₁, D₂, D_3a, D_3b, D₄ and D₅). During D_3a-D₅ the maximum principal stress (σ₁) changed in a clockwise direction from south-west to north-east. Between D₂ and D₃ the intermediate principal stress (σ₂) changed from horizontal to vertical and the interval between D₂ and D₃ marks a transition from thrust to strike-slip tectonics. Relict structures in the porphyroblasts indicate the following mineral growth–deformation evolution in the PjF. (1) Throughout the PjF there was a successive crystallization of garnet (syn-D₁), poryphyroblastic biotite (inter-D_3/4) and staurolite (inter-D_3/4) during the pre-D₄ stage. (2) A syn-D₄-inter-D_4/5 crystallization of kyanite, sillimanite (fibrolite), porphyroblastic tourmaline, magnetite, rutile, cordierite and muscovite–biotite–plagioclase pseudomorphs after staurolite was most localized at and near D₄ shear zones. (3) A syn- to post-D₅ generation of andalusite, ilmenohematite and sheet silicates after staurolite and after cordierite occurred near D₅ faults. The evolution outlined here permits the relative dating of the PjF parageneses, which is used in the second part of the study (Tuisku & Laajoki, 1990), and, together with the knowledge of the pressure–temperature conditions during various growth events, makes it possible to compile pressure–temperature–deformation paths for the PjF.     

Seismic amplifications from offshore to shore

The objective of this study is to determine numerical estimations of seismic amplifications of waves traveling from offshore to shore considering the effect of sea floor configurations. According to the Boundary Element Method, boundary elements were used to irradiate waves and density force can be determined for each element. From this hypothesis, Huygens’ Principle is implemented since diffracted waves are constructed at the boundary from which they are radiated and this is equivalent to Somigliana's theorem. Application of boundary conditions leads to determine a system of integral equations of Fredholm type of second kind, which is solved by the Gaussian method. Various numerical models were analyzed, a first one was used to validate the proposed formulation and some other models were used to show various ideal sea floor configurations to estimate seismic amplifications. Once the formulation was validated, basic slope configurations were studied for estimating spectra of seismic amplifications for various sea floor materials. In general terms, compressional waves (P-waves) can produce seismic amplifications of the incident wave in the order of 2–5. On the other hand, distortional waves (S-waves) can produce amplifications up to 5.5 times the incident wave. A relevant finding is that the highest seismic amplifications due to an offshore earthquake are always located near the shore-line and not offshore despite the seafloor configuration.     

Effects of the oophagous bivalve Acesta oophaga on the morphology and fecundity of its deep‐sea tubeworm host,Lamellibrachia luymesi

The deep‐sea bivalve Acesta oophaga lives attached to the anterior end of the vestimentiferan tubeworm, Lamellibrachia luymesi, at cold methane seeps. The bivalve is found almost exclusively on female tubeworms, where it consumes the lipid‐rich eggs of L. luymesi that are spawned year round (Biological Bulletin, 209, 2005, 87). It is apparent that A. oophaga benefits directly from this close association, but the consequences for the tubeworm host may be more complicated than just a simple predator–prey interaction. Since A. oophaga completely surrounds the tube opening and plume of the worm, it is likely that its presence would limit oxygen uptake by L. luymesi, thereby inhibiting worm growth and reproduction. We hypothesized that occupied tubeworms would compensate for this by growing larger plumes for oxygen uptake. To explore the effects of bivalve presence/absence on female tubeworms, several morphological features, including body size, plume length, tube diameter, and tube segment length, as well as instantaneous fecundity, were compared. Results suggest that the mere presence of A. oophaga has a significant impact on the morphology of its host worm, as all measures of worm size, except for tube segment length, were significantly greater with clams present. Additionally, instantaneous fecundity was 3.5 times higher in occupied worms, implying that tubeworms are not oxygen‐deprived or energy limited as a result of bivalve presence. Our findings suggest that the association between these two deep‐sea organisms may be a more complex form of symbiosis than the simple predator–prey relationship, as previously thought.     

琼东南盆地深水区断层垂向输导及成藏模式

In the Qiongdongnan Basin, faults are well developed.Based on the drilling results, the traps controlled two or more faults are oil-rich. However, when only one fault cut through the sand body, there is no sign for hy-drocarbon accumulation in the sandstone. In terms of this phenomenon, the principle of reservoir-forming controlled by fault terrace is proposed, i.e., when the single fault activates, because of the incompressibility of pore water, the resistance of pore and the direction of buoyancy, it is impossible for hydrocarbon to ac-cumulate in sandstone. But when there are two or more faults, one of the faults acts as the spillway so the hydrocarbon could fill in the pore of sandstone through other faults. In total five gas bearing structures and four failure traps are considered, as examples to demonstrate our findings. According to this theory, it is well-advised that south steep slope zone of Baodao-Changchang Depression, south gentle slope zone of Lingshui Depression, north steep slope zone of Lingshui Depression, and north steep slope zone of Baodao Depression are the most favorable step-fault zones, which are the main exploration direction in next stage.     

沁水煤田赵庄矿区地质构造分析与研究

在野外踏勘和室内资料整理分析的基础上,对赵庄矿区物探工作所查明的断层、井下揭露的断层以及野外观测到的断层进行了断层倾角统计和分断距统计对比分析。对矿区范围内井上下的断层和野外实测节理滑动面的发育规律进行了总结。在此基础上,分析了赵庄矿区地质构造体系及其演化规律。     

Hydraulic properties of the crystalline basement

Hydraulic tests in boreholes, up to 4.5 km deep, drilled into continental crystalline basement revealed hydraulic conductivity (K) values that range over nine log-units from 10⁻¹³−10⁻⁴ m s⁻¹. However, K values for fractured basement to about 1 km depth are typically restricted to the range from 10⁻⁸ to 10⁻⁶ m s⁻¹. New data from an extended injection test at the KTB research site (part of the Continental Deep Drilling Program in Germany) at 4 km depth provide K=5 10⁻⁸ m s⁻¹. The summarized K-data show a very strong dependence on lithology and on the local deformation history of a particular area. In highly fractured regions, granite tends to be more pervious than gneiss. The fracture porosity is generally saturated with Na–Cl or Ca–Na–Cl type waters with salinities ranging from <1 to >100 g L⁻¹. The basement permeability is well within the conditions for advective fluid and heat transport. Consequently, fluid pressure is hydrostatic and a Darcy flow mechanism is possible to a great depth. Topography-related hydraulic gradients in moderately conductive basement may result in characteristic advective flow rates of up to 100 L a⁻¹ m⁻² and lead to significant advective heat and solute transfer in the upper brittle crust. An erratum to this article can be found at     

Tectono–Magmatic Evolution and Metallogenesis along the Northeast Jiangxi Deep Fault, China

Abstract: From the southernmost part of Jiangsu province to the northeastern part of Jiangxi province, China, the Northeast Jiangxi Deep Fault runs for about 400 km length with a width of 30 to 40 km. This fault marks the suture zone of two ter-ranes of Proterozoic age. At the both sides of the fault, Yanshanian granitic activity is recognized. That is, the Dexing-Wuyuan porphyry belt on the NW side of the fault, and the Damaoshan-Lingshan granite belt on the SE side. The former activity is characterized by the occurrence of small stocks of granodioritic composition, rich in siderophile elements but poor in LIL elements. No distinct Eu anomaly is recognized in the REE pattern, and a low initial ⁸⁷Sr/⁸⁶Sr ratio is reported. Magnetite, sphene and apatite are observed as accessory minerals. On the contrary, granitic activity on the SE side of the fault is characterized by the occurrence of composite batholiths, in general of granitic to monzogranitic composition, rich in LIL and alkali elements but poor in siderophile and alkali earth elements. A strong Eu anamaly is recognized in the REE pattern, and initial ⁸⁷Sr/⁸⁶Sr ratios are as high as 0. 716. Fluorite, zircon and REE minerals are observed as accessory minerals. These two contrasting granitic activities are refered to as syntexis– and transformation–types, respectively, following the classification commonly used in China, and have similar petrochemical characteristics to those defined for the magnetite– and ilmenite–series, and I– and S-type granitoids. Considering that the above igneous activity occurred far from the supposed subduction zone along the East Coast of China, intracontinental A-type (continent to continent) subduction is proposed to have occurred northwestwards along the NE Jiangxi Deep Fault during Yanshanian time due to a strong compressional stress from SE to NW. A-type subduction introduced the continental slab to some depth, and resulted in the production of the paired granitic activity observed on both sides of the fault. Many mineral deposits are associated with both granitic belts. In the Dexing-Wuyuan porphyry belt, the Dexing porphyry Cu and Yinshan polymetallic deposits are representative, whereas in the Damaoshan-Lingshan granite belt, several tens of rare metal deposits are known such as the Geyuan Nb–Ta–W–Sn deposits. Metal assemblages of those deposits reflect the source materials of magmas in both granitic belts.