利用断裂带首波分析甘孜—玉树断裂带拉张盆地结构特征

对断裂带及附近区域地层精细结构的描述是理解地震孕育和发生过程的基础.不同板块或块体边界在构造或区域应力作用下,常常会形成速度间断面和低速的断裂带,间断面和低速带的存在会产生特殊的断裂带地震波,比如断裂带首波和围陷波,并会影响地震的物理过程、破裂速度和破裂方向等.本文主要利用2010年4月14日M_W6.9玉树地震后布设的流动地震台站,对沿着甘孜—玉树断裂带传播的断裂带首波进行识别和分析.分析结果表明,在甘孜—玉树断裂带的不同区域均观测到了断裂带首波,在西段的结隆拉张盆地附近的3个台站沿断裂带界面的平均纵波速度差异值在5%～8%,而其他区域的平均速度差异为1%～3%.通过台站位置分布和断裂带首波特征关系,初步分析了断裂带拉张盆地的结构,结果显示结隆盆地的长度为～40km,宽度为5.35～5.97km,深度不超过5km,在地表浅层形成了一个低速区,分别与巴颜喀拉块体(NE)和羌塘块体(SW)产生了两个物性差异界面,但没有延伸到主震和余震区震源深度.我们的结果表明结合密集台阵资料,通过断裂带首波特征分析可以为断裂带精细结构及几何特征提供一种新的技术方法和途径.     

汶川M_W7.9地震起始破裂断层几何结构

本文收集使用紫坪铺水库台网记录到的汶川地震主震P波波形资料,利用P波反投影叠加法获取了2008年5月12日汶川M_W7.9地震起始破裂的时空演化过程.通过分析本次大地震起始破裂阶段(0～1s)破裂点在三维空间内的分布特征,确定了本次大地震起始破裂位置及起始破裂断层几何结构模型.得到以下结果:汶川地震起始破裂点位于31.013±0.002°N、103.392±0.002°E,震源深度为8.2±0.4km,发震时刻为2008年5月12日14∶27∶58.80±0.4.汶川地震起始破裂的最佳断层面走向为NE48°,倾向NW35°,起始阶段破裂的深度范围为地下7.5～9km.     

APPLYING 3D INVERSION OF SINGLE-PROFILE MAGNETOTELLURIC DATA TO IDENTIFY THE SHADE AND YUNONGXI FAULTS

Many synthetic model studies suggested that the best way to obtain good 3D interpretation results is to distribute the MT sites at a 2D grid array with regular site spacing over the target area. However, MT 3D inversion was very difficult about 10 years ago. A lot of MT data were collected along one profile and then interpreted with 2D inversion. How to apply the state-of-the-art 3D inversion technique to interpret the accumulated mass MT profiles data is an important topic. Some studies on 3D inversion of measured MT profile data suggested that 2D inversions usually had higher resolution for the subsurface than 3D inversions. Meanwhile, they often made their interpretation based on 2D inversion results, and 3D inversion results were only used to evaluate whether the overall resistivity structures were correct. Some researchers thought that 3D inversions could not resolute the local structure well, while 2D inversion results could agree with the surface geologic features much well and interpret the geologic structures easily. But in the present paper, we find that the result of 3D inversion is better than that of 2D inversion in identifying the location of the two local faults, the Shade Fault(SDF)and the Yunongxi Fault(YNXF), and the deep structures. In this paper, we first studied the electrical structure of SDF and YNXF based on a measured magnetotelluric(MT) profile data. Besides, from the point of identifying active faults, we compared the capacity of identifying deep existing faults between 2D inversion models and 3D models with different inversion parameters. The results show that both 2D and 3D inversion of the single-profile data could obtain reasonable and reliable electrical structures on a regional scale. Combining 2D and 3D models, and according to our present data, we find that both SDF and YNXF probably have cut completely the high resistivity layer in the upper crust and extended to the high conductivity layer in the middle crust. In terms of the deep geometry of the faults, at the profile's location, the SDF dips nearly vertically or dips southeast with high dip angle, and the YNXF dips southeast at depth. In addition, according to the results from our measured MT profile, we find that the 3D inversion of single-profile MT data has the capacity of identifying the location and deep geometry of local faults under present computing ability. Finally, this research suggests that appropriate cell size and reasonable smoothing parameters are important factors for the 3D inversion of single-profile MT data, more specifically, too coarse meshes or too large smoothing parameters on horizontal direction of 3D inversion may result in low resolution of 3D inversions that cannot identify the structure of faults. While, for vertical mesh size and data error thresholds, they have limited effect on identifying shallow tectonics as long as their changes are within a reasonable range. 3D inversion results also indicate that, to some extent, adding tippers to the 3D inversion of a MT profile can improve the model's constraint on the deep geometry of the outcropped faults.     

RESEARCH ON THE CHARACTERISTICS OF QUATERNARY ACTIVITIES OF SU-XI-CHANG FAULT

Running across the urban areas of Changzhou, Wuxi and Suzhou, the NW-trending Su-Xi-Chang Fault is an important buried fault in Yangtze River Delta. In the respect of structural geomorphology, hilly landform is developed along the southwest side of the Su-Xi-Chang Fault, and a series of lakes and relatively low-lying depressions are developed on its northeast side, which is an important landform and neotectonic boundary line. The fault controlled the Jurassic and Cretaceous stratigraphic sedimentary and Cenozoic volcanic activities, and also has obvious control effects on the modern geomorphology and Quaternary stratigraphic distribution. Su-Xi-Chang Fault is one of the target faults of the project "Urban active fault exploration and seismic risk assessment in Changzhou City" and "Urban active fault exploration and seismic risk assessment in Suzhou City". Hidden in the ground with thick cover layer, few researches have been done on this fault in the past. The study on the activity characteristics and the latest activity era of the Su-Xi-Chang Fault is of great significance for the prevention and reduction of earthquake disaster losses caused by the destructive earthquakes to the cities of Changzhou, Wuxi and Suzhou. Based on shallow seismic exploration and drilling joint profiling method, Quaternary activities and distribution characteristics of the Su-Xi-Chang Fault are analyzed systematically. Shallow seismic exploration results show that the south branch of the Su-Xi-Chang Fault in Suzhou area is dominated by normal faulting, dipping to the north-east, with a dip angle of about 60° and a displacement of 3~5m on the bedrock surface. The north branch of the Su-Xi-Chang Fault in Changzhou area is dominated by normal faulting, dipping to the south, with a dip angle of about 55°~70° and a displacement of 4~12m on the bedrock surface. All breakpoints of Su-Xi-Chang Fault on the seismic exploration profiles show that only the bedrock surface was dislocated, not the interior strata of the Quaternary. On the drilling joint profile in the Dongqiao site of Suzhou, the latest activity of the south branch of Su-Xi-Chang Fault is manifested as reverse faulting, with maximum displacement of 2.9m in the upper part of Lower Pleistocene, and the Middle Pleistocene has not been dislocated by the fault. The fault acts as normal fault in the Pre-Quaternary strata, with a displacement of 3.7m in the Neogene stratum. On the drilling joint profile in the Chaoyang Road site of Changzhou, the latest activity of the north branch of Su-Xi-Chang Fault is manifested as reverse faulting too, with maximum displacement of 2.8m in the bottom layer of the Middle Pleistocene. The fault acts as normal fault in the Pre-Quaternary strata, with a displacement of 10.2m in the bedrock surface. Combining the above results, we conclude that the latest activity era of Su-Xi-Chang Fault is early Middle Pleistocene. The Su-Xi-Chang Fault was dominated by the sinistral normal faulting in the pre-Quaternary period, and turned into sinistral reverse faulting after the early Pleistocene, with displacement of about 3m in the Quaternary strata. The maximum magnitude of potential earthquake on the Su-Xi-Chang Fault is estimated to be 6.0.     

徐家围子断陷深层火石岭组致密火山岩储层地应力分布规律研究

徐家围子断陷位于松辽盆地北部,其深层中生代火石岭组为致密火山岩气藏,天然裂缝发育,地应力分布非均质性强。结合诱导裂缝法与井径崩落法进行单井现今地应力方向分析,利用声波测井法计算现今地应力大小的纵向分布。依据火石岭组构造顶底面图、火山岩相组及断层分布特征建立非均质三维地质模型;在动、静态岩石物理参数拟合校正的基础上,结合实验测试及已有研究成果,确定不同岩相组和断层岩石物理参数,建立三维力学模型;利用Ansys有限元数值模拟软件建立火石岭组三维数学模型并进行相关运算获得三维现今地应力分布模型。计算结果表明在火石岭组地层中,水平最大主应力方向主要为东西向,应力值范围在86~110 MPa;水平最小主应力方向主要为南北向,应力值范围在67~84 MPa。分析模拟结果可知火山岩相、断层和构造起伏三者对火石岭组现今地应力分布影响较大。其中水平主应力的方向主要受断层和近火山口相分布的影响,而水平主应力的大小则是受三者综合作用。在构造低部位,近火山口相组发育处,断层上盘及断层端部皆为主应力的集中区域。依据现今地应力研究成果可为徐家围子断陷下一步开发井网部署、压裂改造方案和水平井的设计以及注水管理提供重要指导。      

A 3D structural analysis of the Goliat field,Barents Sea,Norway

The Goliat field consists of Middle to Late Triassic reservoirs which exploit an elongate anticline (the Goliat anticline) in the hanging wall of the Troms-Finnmark Fault Complex (TFFC), offshore Norway. The area is affected by a dense network of multiple trending fault populations which historically have inhibited seismic resolution owing to persistent fault shadow. Seismic investigations utilising a multi-azimuth three-dimensional survey (EN0901) allow much crisper delineation of seismic features previously unattainable by vintage single-azimuth surveys. Three dominant fault populations are identified in the area, two of which parallel TFFC segments, the Alke–Goliat (WSW–ENE) and the Goliat–Tornerose (NNE–SSW) segments. The Goliat field is located within a zone of intersection between both segments. A third E–W trending fault population, the Hammerfest Regional population, is likely influenced by the offshore extension of the Trollfjord-Komagelv Fault Complex (TKFZ). A local NW–SE trending fault population, the Goliat Central, affects the Goliat anticline and partitions Alke–Goliat and Goliat–Tornerose subsidiary faults resulting in curvilinear traces. Several cross-cutting relationships between fault populations are observed and may provide fluid compartmentalisation in the reservoirs. Compilation of regional transects and the EN0901 survey provides new insight into the evolution of the Goliat anticline which is underlain by a fault-bound basement terrace that became established in the Late Palaeozoic. The structure is interpreted to have formed due to vertical segmentation of the TFFC and cores the overlying broad anticline. The western limb of the Goliat anticline likely formed by differential compaction, whereas the eastern limb is primarily a result of hanging wall roll-over linked to variable listric to ramp-flat-ramp fault geometry. Rifting took place in the Palaeozoic (Carboniferous to Permian?), and in the Mesozoic, possibly as early as the Late Triassic, with a major event in the Late Jurassic to Early Cretaceous. Minor reactivations continued into the Late Cretaceous, and possibly the Early Cenozoic. Mesozoic syn-kinematic geometries in the hanging wall of the Goliat–Tornerose TFFC segment are consistent with deposition during up section propagation of a blind fault, over which, a monocline was established and later breached. Jogs (abrupt orientation changes) in fault traces, transverse folds (associated with displacement maxima/minima) and vertical fault jogs suggest the TFFC existed as a greater number of segments prior to amalgamation during the Late Triassic to Jurassic. A phase of Barremian inversion created local compression structures above blind extensional faults, and deeper seated buttressing against large faults. Polygonal faults affect the Late Cretaceous to Early Cenozoic successions.     

New insights into the carbonate karstic fault system and reservoir formation in the Southern Tahe area of the Tarim Basin

As worldwide hydrocarbon exploration has extended from shallowly to deeply buried strata, reservoir quality has attracted substantial and persistent interest in petroleum geology. In particular, deeply buried strata (>5500 m) in the Tarim Basin have attracted considerable attention because carbonate reservoirs that have experienced fracture or dissolution have also been shown to demonstrate considerable hydrocarbon potential. Therefore, it is necessary to determine how these reservoirs are developed and distributed in detail from both scientific and practical standpoints.In this paper, we address this issue using a case study in the southern Tahe area, which is contained within the largest Palaeozoic marine oilfield in China. In the northern Tahe area, mega-paleokarst systems developed in the Ordovician strata; however, the reservoir quality in the southern part of the Tahe area is relatively poor because it is covered by insoluble formations during karstification. Observations of cores and analyses of images of well logging demonstrate that these reservoirs are dominated by caves, vugs and fractures that have developed near faults. We speculate that the faults penetrating insoluble formations represent the main dissolution passages that originally developed these karstic fault systems. Additionally, we analyse a series of outcrops, seismic data, and structures to characterize the spatial geometry of these major faults and their surrounding fractures in detail. Most of these are strike-slip faults, and their subsequent reservoirs can be divided into three categories based on their development, including dendritic, sandwich and slab reservoirs. Recent studies demonstrate that karstic fault reservoirs are most common traps in the study area. Although various types of carbonate karstic fault reservoirs are represented in this region, the dendritic karstic fault reservoir is the most hydrocarbon-rich.Guided by these initial results, 108 wells were drilled from 2013 to 2014, producing 485 thousand tons of oil and yielding success ratios greater than 89%. The average production of dendritic reservoirs is 37.4 tons per day (t/d), while those of sandwich and slab types are 20.2 t/d and 14.0 t/d, respectively. These results represent significant references for future hydrocarbon exploration and the development of similar deeply buried karstic fault reservoirs in the Tarim Basin and elsewhere.     

Geochemistry and origin of organic-rich sediment veins in fractured granitic basement,Helmsdale, Sutherlandshire,UK

Black sediment veins up to 2 cm width penetrate the Caledonian Helmsdale Granite in the vicinity of the Helmsdale Fault, onshore Moray Firth. The black colour and geochemistry of the veins reflect a high content of organic carbon. Both Devonian and Jurassic shales are conceivable available sources, but sterane compositions relate the organic matter to the Jurassic shales. A content of extractable organic matter higher than in the shales suggests that the carbon in the veins represents oil rather than mechanically mobilized shale. The oil was present during sediment vein emplacement. The veins were emplaced forcefully, which may reflect high fluid pressure associated with post-Jurassic movement on the Helmsdale Fault.     

Examining fault architecture and strain distribution using geospatial and geomechanical modelling: An example from the Qaidam basin,NE Tibet

The investigation of complex geological setting is still dominated by traditional geo-data collection and analytical techniques, e.g., stratigraphic logging, dip data measurements, structural ground mapping, seismic interpretation, balance section restoration, forward modelling, etc. Despite the advantages of improving our understanding in structural geometry and fault architecture, the geospatial modelling, applying computer-aided three-dimensional geometric design, visualization and interpretation, has rarely been applied to such complex geological setting. This study used the Lenghu fold-and-thrust belt (in Qaidam basin, NE Tibetan Plateau) to demonstrate that the application of geospatial and geomechanical modelling could improve our understanding and provide an effective technique for investigating the fault architecture and strain distribution. The three-dimensional configuration of the Lenghu fold-and-thrust belt was initially derived from traditional analysis techniques, such as regional stratigraphic logging, cross section construction, meso-scale ground mapping and landsat image interpretation. The high-resolution field data and landsat image were integrated to construct the geospatial model, which was subsequently used to quantitatively investigate the fault throw changes along the Lenghu thrust fault zone and to understand its control on the lateral structural variation. The geospatial model was then restored in three dimensions to reveal the kinematic evolution of the Lenghu fold-and-thrust belt. Geomechanical modelling, using a Mass-Spring algorithm, provided an effective three-dimensional tool for structural strain analysis, which was used to predict the strain distribution throughout the overall structure, e.g., normal faults with throws ranging from meters to tens of meters in the hanging-wall. The strain distribution predicted by geomechanical modelling was then validated by the natural normal faults in the hanging-wall. The high accordance between the strain prediction and statistics of natural normal faults demonstrates good applicability of geospatial and geomechanical modelling in the complex geological setting of the Lenghu fold-and-thrust belt. The geospatial models and geomechanical models, therefore, can provide a robust technique for analyzing and interpreting multi-source data within a three-dimensional environment. We anticipate that the application of three-dimensional geospatial modelling and geomechanical modelling, integrating both multi-source geologic data and three-dimensional analytical techniques, can provide an effective workflow for investigating the fault architecture and strain distribution at different scales (e.g., ranging from regional-to meso-scale).     

新元古代沂沭海峡地震引发的软沉积物变形及其微量元素信息*

新元古代沂沭海峡位于郯庐断裂带昌邑—大店断层西侧宽60~90,km、长300,km的区域内,其分布范围基本与郯庐断裂带中段一致。新元古代,该海峡盆地先后沉积了青白口系、南华系及震旦系的滨—浅海相陆源碎屑、泥质及碳酸盐沉积物,其岩石地层称之为土门群。本次研究从该海峡盆地土门群佟家庄组(由石英砂岩、泥灰岩和页岩组成,属南华系)、浮来山组(由细—粉砂岩夹页岩组成,属震旦系)及石旺庄组(主要由碳酸盐岩组成,下部夹页岩,属震旦系)中鉴别出了一系列地震触动软沉积物形成的变形构造,包括液化砂墙和砂脉、负载构造、火焰构造、球枕构造、软布丁构造、底辟构造、滑塌褶曲和同沉积断层等。它们是地震事件的记录——震积岩。新元古代中晚期(约800—600,Ma)沂沭海峡盆地拉张裂陷是它们形成的动力机制。根据石旺庄组中的微亮晶方解石脉与地震成因的变形构造(如负载、火焰、软布丁及同沉积断层等)共(伴)生的事实,并结合模拟地震试验结果分析,认为微亮晶方解石脉很可能是地震引发的饱和灰泥(方解石微粒)液化脉。微量化学元素分析结果表明,这些震积岩中的w(La)/w(Sc)和 w(La)/w(Th)值高于上地壳平均值和正常沉积层,而w(Th)/w(Sc)值则较低,深源微量元素Ni和Cr的含量也高于上地壳平均值及正常沉积层。这些微量元素特征是当时的盆地基底不稳定、快速沉积且伴有深部物质元素混入的反映,强地震很可能是快速沉积和促进深源物质混入的主要动力。土门群中发育的一系列地震引起的软沉积物变形(震积岩),再次证明了古郯庐断裂带的存在,由它们记录的地震事件也是晋宁运动乃至Rodinia超大陆的裂解的响应。