A response‐based decoupling criterion for multiply‐supported secondary systems

It is often infeasible to carry out coupled analyses of multiply‐supported secondary systems for earthquake excitations. ‘Approximate’ decoupled analyses are then resorted to, unless the response errors due to those are significantly high. This study proposes a decoupling criterion to identify such cases where these errors are likely to be larger than an acceptable level. The proposed criterion is based on the errors in the primary system response due to decoupling and has been obtained by assuming (i) the input excitation to be an ideal white noise process, (ii) cross‐modal correlation to be negligible, and (iii) the combined system to be classically damped. It uses the modal properties of the undamped combined system, and therefore, a perturbation approach has been formulated to determine the combined system properties in case of light to moderately heavy secondary systems. A numerical study has been carried out to illustrate the accuracy achieved with the proposed perturbation formulation. The proposed decoupling criterion has been validated with the help of two example primary‐secondary systems and four example excitation processes. Copyright © 2002 John Wiley & Sons, Ltd.     

Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

Study of a semi‐active stiffness damper under various earthquake inputs

Semi‐active stiffness damper (SASD) is one of many semi‐active control systems with the capability to mitigate the dynamic response using only a small amount of external power. The system consists of a hydraulic damper connected to the bracing frame in a selected story unit. In this paper, study of a SASD in two building models of five‐stories under four benchmark earthquake records is reported. The purpose of this study is to evaluate the effectiveness of the control system against structure type and varying earthquake inputs. Various control laws are chosen to work with SASD, such as: resetting control, switching control, linear quadratic regulator (LQR) and modified LQR, and the results are compared with no control and passive control cases. Numerical results show that the use of a SASD is effective in reducing seismic responses. Control effectiveness is dependent on the type of structure and earthquake excitation. Passive control is less effective than other control cases as expected. Resetting control, switching control and LQR generally perform similarly in response reduction. While modified LQR is more efficient and robust compared with other control algorithms. Copyright © 2002 John Wiley & Sons, Ltd.     

Towards a direct collapse–load method of design for concrete frames subjected to severe ground motions

Most current methods of design for concrete structures under earthquake loads rely on highly idealized ‘equivalent’ static representations of the seismic loads and linear‐elastic methods of structural analysis. With the continuing development of non‐linear methods of dynamic analysis for the overload behaviour and collapse of complete concrete structures, a more direct and more accurate design procedure becomes possible which considers conditions at system collapse. This paper describes an evaluation procedure that uses non‐linear dynamic collapse–load analysis together with global safety coefficients. A back‐calibration procedure for evaluating the global safety coefficients is also described. The aim of this paper is to open up discussion of alternative methods of design with improved accuracy which are necessary to move towards a direct collapse–load method of design. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

Ground‐shaking mapping for a scenario earthquake considering effects of geological conditions: a case study for the 1995 Hyogo‐ken Nanbu,Japan earthquake

In order to examine the applicability of ground‐shaking mapping techniques to a near‐field earthquake, a peak ground velocity map of the 1995 Hyogo‐ken Nanbu, Japan earthquake computed from seismic zoning methods that consider the effects of geological conditions is compared with the actual observed intensity map. When computing the ground‐shaking map, the site amplification at each site is calculated in terms of the average shear‐wave velocity of the ground estimated from the corresponding geomorphological conditions. This map shows a relatively good agreement with the observed intensity map. However, the computations provide smaller values for certain disastrous areas of the earthquake, where the effects on ground motion of a deep, irregular underground structure have been reported. The effect of such structures on site response is examined implementing 2D FEM analyses, thereby being also incorporated into the method. Results considering the effect of the irregular underground structure show better agreement with the observed intensity map. Copyright © 2002 John Wiley & Sons, Ltd.     

Tectonic setting and petrogenesis of the Çelebi granitoid, (Kırıkkale-Turkey) and comparison with world skarn granitoids

Many studies have shown systematic correlations between the composition of plutons worldwide and the metal content of associated skarns. This is the first report of similar correlations between the composition of Çelebi granitoid and skarns of the Çelebi district in Central Anatolia, Turkey. The Çelebi district is well known for its polymetallic Fe–W and Cu vein ores. These are hosted by calcic skarn zones. Both exoskarns (pyroxene–garnet) and endoskarns (epidote–pyroxene) occur in the district formed mainly along the granitoid contacts and along the fractures within the marble. Based on mineralogy, petrology and geochemistry, two different igneous rocks were recognized in the Çelebi granitoid, referred to as leucocratic (felsic) and mesocratic (intermediate) Çelebi granitoid. The leucocratic Çelebi occurs as dominant rock type, and is classified as granite. The mesocratic Çelebi is not widespread and is classified as adamellite, tonalite, quartz monzonite and quartz monzodiorite. The mesocratic Çelebi has I-type characteristics, and have subalkaline, calc-alkaline and metaluminous characteristics like most worldwide skarn granitoids.A post-collisional tectonic setting is proposed on the basis of field evidence, the relative timing of intrusions with respect to metamorphic and obducted ophiolitic rocks and trace element geochemistry. The high abundance of La and Ce and the enrichment of V in mafic components suggest that Çelebi granitoids are formed by partial melting of mantle rocks, but have been contaminated by interaction with continental crust involving possible magma mixing processes (i.e. mixing of coexisting felsic and mafic magmas). In the district, the mesocratic type and mafic microgranular enclaves (MME) mainly within leucocratic type represent a mafic underplating magma that was mixed with and/or injected into felsic magma of the leucocratic type.The present study shows that Fe mineralization is associated with mesocratic Çelebi type, whereas W mineralization is associated with leucocratic type. Mesocratic Çelebi granitoid is significantly different from the worldwide average of plutons associated with Fe skarns. In particular, MgO vs. SiO₂, FeOt+CaO+Na₂O/K₂O vs. SiO₂, Fe₂O₃/Fe₂O₃+FeO vs. SiO₂ and V vs. Ni vary from typical values (are lower than values typical for plutons associated with Fe skarns) for plutons associated with Fe skarns. Instead, it resembles the geochemical characteristics of plutons associated with worldwide Cu and possibly Au skarns. This suggests new exploration possibilities for copper and gold in the Çelebi district.     

2000年4月29日内乡ML4.7级地震前潢川地电异常变化

2000年4月29日11时54分，河南省南阳市内乡县马山口镇与镇平县寺山乡之间发生一次ML4.7级地震。地震前3天，潢山台视电阻率ρs异常较为明显。分析了此次异常与内乡ML4.7级地震的关系，认为此次异常很有可能是内乡ML4.7级地震的短临前兆异常。当观测台站与震源位于同一构造带时，即便离震中较远，地电阻率对地震异常反映仍较灵敏，且与构造带同一走向的测向尤为明显。     

Use of Chemotaxonomy To Study the Influence of Benzalkonium Chloride on Bacterial Populations in Biodegradation Testing

Contradictory results are reported for the behaviour of quaternary ammonium compounds (QACs) in sewage treatment plants (STPs). QACs may sorb onto activated sludge. Only little information is available with respect to effects of QACs against bacteria in STPs. Only 5 to 15 % of bacteria present in sewage sludge can be detected by means of culture dependent microbiological methods. The shift of the bacterial populations due to effects of test compounds have not been studied up to now with culture independent methods. The microbial populations shift was studied in situ using culture independent chemotaxonomy profiling ubiquinones and polyamines. Additionally, toxic effects of QACs against bacteria present in the test vessels of the Zahn‐Wellens test (OECD 302 B) were assessed with a toxicity control in the test. The ubiquinone profiles representing changes in Gram‐negative populations mainly showed that the activated sludge was affected only in test vessels containing benzalkonium chloride. According to chemotaxonomy Acinetobacter or/and some members of Pseudomonas spp. have been selected by benzalkonium chloride after some adaptation period (8 to 12 days).     

Simulation of individual particle movement in a gravel streambed

A two‐dimensional simulation model of travel distances of individual particles in a gravel‐bed river is presented. The model is based on a number of rules, which include particle size, entrainment, trajectory, distance of movement and entrapment. Particle interactions are controlled by resistance fields defined about each obstacle and critical elevation defined in the model. Resistance fields, particle dropping and critical elevation rules control particle interactions. The interaction rules cause the particles to develop pebble clusters, stone cells and transverse structures (transverse ribs). The simulated travel distances of individual particles are consistent with reported field results. Individual particle travel distances were simulated using two different models; one without interactions between the individual particles and the stationary bed and one with interactions. The case without interactions demonstrates the random nature of sediment transport, and narrow ranges of travel distances. Wider ranges of travel distances, similar to those for natural situations, were obtained for the cases with interactions. The more intense the interaction between the mobile stones and the stationary ones, the wider the range of distances of travel for a given particle size. Modelling the mean travel distance yielded a result similar to that published previously, which was based on empirical data. Well developed bed‐surface structures were obtained for relatively poorly sorted sediment with intense interactions between particles. Transverse structures developed when relatively large particles were allowed to move. Copyright © 2002 John Wiley & Sons, Ltd.