IAP/LASG全球海-陆-气耦合系统模式的纬向平均大气气候态分析(英文)

分海洋和陆地两种情况来讨论IAP/LASG全球海-陆-气耦合系统模式（GOAL）四个版本的结果,并与观测资料进行对比分析。一些重要的大气变量包括表面空气温度,海平面气压和降水率用来评估GOALS模式模拟当代气候和气候变率的能力。总的来说,GOALS模式的四个版本都能够合理地再现观测到的平均气候态和季节变化的主要特征。同时评估也揭示了模式的一些缺陷。可以清楚地看到模拟的全球平均海平面气压的主要误差是在陆地上。陆地上表面空气温度模拟偏高主要是由于陆面过程的影响。值得注意的是降水率模拟偏低主要是在海洋上,而中高纬的陆地降水在北半球冬天却比观测偏高。 通过模式不同版本之间的相互比较研究,可以发现模式中太阳辐射日变化物理过程的引入明显地改善了表面空气温度的模拟,尤其是在中低纬度的陆地上。太阳辐射日变化的引入对热带陆地的降水和中高纬度的冬季降水也有较大改进。而且,由于使用了逐日通量距平交换方案（DFA）,GOALS模式新版本模拟的海洋上的温度变率在中低纬度有了改善。 比较观测和模拟的年平均表面空气温度的标准差,可以发现GOALS模式四个版本都低估了海洋和陆地上的温度变率,文中还对影响观测和模拟温度变率差异的可能原因进行了探讨。     

Can A Cup Anemometer `Underspeed'?

An analysis of cup-anemometer dynamics has been carried out inorder to determine whether the mean-wind velocity can have anegative bias. This would be contrary to the general belief thatcup anemometers always overspeed. Compared to prior analyses, theeffect of a possible nonlinearity of the calibration function isincluded. The conclusion is that neither longitudinal nor lateralvelocity fluctuations can contribute significantly to a negativebias. However, if a cup anemometer has an angular response thatfalls below the ideal cosine response, there will, as demonstratedin the concluding discussion, be a negative contribution from thevertical velocity fluctuations to the total bias, and thiscontribution may even outbalance the positive contributions fromthe longitudinal velocity fluctuations. Concrete evidence of suchexotic cup anemometer behaviour has not been reported in theliterature.     

体感温度的研究及业务化应用

体感温度是人们对环境温度的综合反应，与人的生活需求密切相关。本文就其概念、研究意义和方法进行了阐述，并结合乌鲁木齐地区的气候特点，提出了符合本地区的体感温度的经验公式并实现业务化应用。     

平落坝储层有机包裹体特征与气藏形成过程研究

通过储集层成岩作用与有机包裹体的研究认为,研究区储集层有机包裹体主要通过交代和重结晶作用而形成,有各种相态形式,主要分布在石英颗粒内溶蚀缝或孔隙中,构造裂缝中基本未见有机包裹体。上三叠统储集层包裹体丰度明显高于侏罗系沙溪庙组。香二气藏砂岩有机包裹体均一温度主峰在 10 0～ 110℃;沙溪庙气藏砂岩有机包裹体均一温度主峰在 90～ 10 0℃。香二气藏形成时间早,经历了印支期少量注入到印支期末-喜山早期大量注入,再到喜山晚期调整、部分注入的过程。沙溪庙气藏天然气注入则主要发生于喜山运动期。     

Seismic response of self‐centring hysteretic SDOF systems

The seismic response of single‐degree‐of‐freedom (SDOF) systems incorporating flag‐shaped hysteretic structural behaviour, with self‐centring capability, is investigated numerically. For a SDOF system with a given initial period and strength level, the flag‐shaped hysteretic behaviour is fully defined by a post‐yielding stiffness parameter and an energy‐dissipation parameter. A comprehensive parametric study was conducted to determine the influence of these parameters on SDOF structural response, in terms of displacement ductility, absolute acceleration and absorbed energy. This parametric study was conducted using an ensemble of 20 historical earthquake records corresponding to ordinary ground motions having a probability of exceedence of 10% in 50 years, in California. The responses of the flag‐shaped hysteretic SDOF systems are compared against the responses of similar bilinear elasto‐plastic hysteretic SDOF systems. In this study the elasto‐plastic hysteretic SDOF systems are assigned parameters representative of steel moment resisting frames (MRFs) with post‐Northridge welded beam‐to‐column connections. In turn, the flag‐shaped hysteretic SDOF systems are representative of steel MRFs with newly proposed post‐tensioned energy‐dissipating connections. Building structures with initial periods ranging from 0.1 to 2.0s and having various strength levels are considered. It is shown that a flag‐shaped hysteretic SDOF system of equal or lesser strength can always be found to match or better the response of an elasto‐plastic hysteretic SDOF system in terms of displacement ductility and without incurring any residual drift from the seismic event. Copyright © 2002 John Wiley & Sons, Ltd.     

Damaging properties of ground motions and prediction of maximum response of structures based on momentary energy response

Dynamic damaging potential of ground motions must be evaluated by the response behaviour of structures, and it is necessary to indicate what properties of ground motions are most appropriate for evaluation. For that purpose, the behaviour of energy input process and hysteretic energy dissipation are investigated in this study. It is found that the momentary input energy that is an index for the intensity of input energy is related to the characteristics of earthquakes such as cyclic or impulsive, and to the response displacement of structures immediately. On the basis of these results, a procedure is proposed to predict inelastic response displacement of structures by corresponding earthquake input energy to structural dissipated damping and hysteretic energy. In this procedure the earthquake response of structures is recognized as an input and dissipation process of energy, and therefore structural properties and damaging properties of ground motions can be taken into account more generally. Lastly, the studies of the pseudodynamic loading test of reinforced concrete structure specimens subjected to ground motions with different time duration are shown. The purpose of this test is to estimate the damaging properties of ground motions and the accuracy of the proposed prediction procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

Probabilistic analysis of peak response of MDOF systems with uncertain PSD function

The use of uniform hazard spectra which have the same probability of exceedance at different frequencies has been proposed for the future version of the National Building Code of Canada. Commonly used combination rules to estimate the peak responses of multi‐degree‐of‐freedom (MDOF) systems are the square root of sum of squares rule and the complete quadratic combination rule. However, the probability that the peak response of a MDOF system exceeds the one estimated by using these rules with the peak modal responses from the uniform hazard spectra cannot be inferred directly. The assessment of the probability of exceedance of the peak response of MDOF systems is presented by considering that the uncertainty in seismic excitation due to all potential earthquakes can be lumped in the power spectral density function of the ground acceleration with uncertain model parameters. This probability is evaluated based on the random vibration of linear systems and the first‐order reliability method. It is found that the under‐ or over‐estimations are less than about 5 or 10% if the modal contributions are not within 10–90% of, or not within 20–80% of, the absolute sum of the effective modal peak responses, respectively. Otherwise, severe under‐ or over‐estimation could result. Copyright © 2002 John Wiley & Sons, Ltd.     

应用等效纬度-海拔模型进行地温及多年冻土制图

This research presents a method for permafrost mapping in discontinuous permafrost regions based on equivalent latitude/elevation concept in interior Alaska. In winter months, study site has a strong temperature inversion in air up to 700 m elevation. Air temperature data and the effects of slope, aspect and elevation were used to create an equivalent latitude/elevation model. This model was well correlated with mean annual surface temperature (0.79). In this watershed, the thawing index (It≈1 400 ℃*days) at the ground surface and snow depth do not vary greatly from south facing to north facing slopes. The primary controlled factor that determines the mean annual surface temperature was the winter surface temperature. The permafrost stability is effectively controlled by the freezing index. We determined 37.5% of Caribou-Poker Creeks Research Watershed has unstable or thawing permafrost. At least 2.1% of the permafrost in this watershed may have disappeared in the last 90 years due to climate warming. This method makes it possible to evaluate the permafrost stability in the present, past and future.     

H2O-CH4-H2-CO2-CO-O2在高温、高压和高密度条件下的状态方程

为了计算高温，高压和高密度流体的热力学性质，提出了一个具有19个参数的维里型状态方程，其中参数与温度间的函数关系采用由Sutherland位能函数导出的维里系数近似式。除临界点附近以外，在已报道的pVT数据所覆盖的大部分超临界区域内，该方程均可适用。用该方程对H2O，CH4，H2，CO2，CO和O2等流体pVT关系的计算结果令人满意，其中pVT上限分别为：91-610GPa,1.6-11.0cm^3/mol,4000-5000K。计算体积的平均偏 小于0．8％，最大偏差小于5．4％。     

低温电镀孕镶金刚石石油取心钻头研制与应用

该钻头用于坚硬地层取心。河南油田以往常用园柱聚晶、三角聚晶钻头以及烧结孕镶金刚石钻头，取心效率低、钻速慢、成本高。近两年采用低温电镀孕镶金刚石钻头取心后，平均单筒进尺由原来的4．20m／筒提高到7．62m/筒，平均取心机械钻速由原来的0．21m/h提高到的0.84m/h。该钻头生产工艺完全改变原来高温（1000℃以上）烧结为低温（室温）电镀工艺，极大地避免了金刚石热损伤，采用高强度大颗粒的金刚石，提高了取心机械钻速。