Study on Recovering the Earth＇s Potential Field Based on GOCE Gradiometry

Given the second radial derivative Vrr（P） ｜δs of the Earth＇s gravitational potential V（P） on the surface δS corresponding to the satellite altitude, by using the fictitious compress recovery method, a fictitious regular harmonic field rrVrr（P）^＊ and a fictitious second radial gradient field V：（P） in the domain outside an inner sphere Ki can be determined, which coincides with the real field V（P） in the domain outside the Earth. Vrr^＊（P）could be further expressed as a uniformly convergent expansion series in the domain outside the inner sphere, because rrV（P）^＊ could be expressed as a uniformly convergent spherical harmonic expansion series due to its regularity and harmony in that domain. In another aspect, the fictitious field V^＊（P） defined in the domain outside the inner sphere, which coincides with the real field V（P） in the domain outside the Earth, could be also expressed as a spherical harmonic expansion series. Then, the harmonic coefficients contained in the series expressing V^＊（P） can be determined, and consequently the real field V（P） is recovered. Preliminary simulation calculations show that the second radial gradient field Vrr（P） could be recovered based only on the second radial derivative V（P）｜δs given on the satellite boundary. Concerning the final recovery of the potential field V（P） based only on the boundary value Vrr （P）｜δs, the simulation tests are still in process.     

SOME NEW UNDERSTANDINGS OF LAND-SURFACE PROCESSES IN ARID AREA FROM THE HEIFE*

The survey for the HEIFE(Atmosphere-Land Surface Processes Experiment at Heihe River Basin,Western China) is given in the paper.The following basic subjects for land-surface processes in arid areas are studied:(1) the general characteristics of the energy budget on ground surface in arid areas;(2) the parameterization of the land surface processes;(3) the interaction between oasis and its desert circumstances,a special phenomenon in arid areas.The analysis shows that the sensible heat flux in the surface energy budget is in the majority,and the latent heat flux may be neglected.The influence of atmospheric stratification stability on the turbulent transfer of energy and substance must be considered in parameterization of land surface processes in arid areas.The "cold island effect" phenomenon in oasis and the "humidity inversion" phenomenon in desert near oasis are the result of the interaction between them.The results would improve the understanding of land surface processes in arid areas.     

Strain analysis in Jurassic argillites of the Monte Sirino area (Lagonegro Zone,southern Apennines,Italy) and implications for deformation paths in pelitic rocks

Analysis of strain in Jurassic argillites forming part of the folded and thrusted sedimentary succession of the Lagonegro basin (southern Italian Apennines) has been carried out using ellipsoid-shaped reduction spots as strain markers. Most of the determined finite strain ellipsoids are of oblate type and show a peculiar distribution of the maximum extension direction (X), with maxima either subparallel or subperpendicular to the local fold axes. Using the strain matrix method, two different deformation histories have been considered to assist the interpretation of the observed finite strain pattern. A first deformation history involved vertical compaction followed by horizontal shortening (occurring by a combination of true tectonic strain and volume loss), whereby all strain is coaxial and there is no change in the intermediate axis of the strain ellipsoid. By this type of deformation sequence, which produces a deformation path where total strain moves from the oblate to the prolate strain field and back to the oblate field, prolate strain ellipsoids can be generated and may be recorded where tectonic deformation has not been large enough to reverse pretectonic compaction. This type of deformation history may be of local importance within the study area (i.e. it may characterize some fold hinge regions) and, more generally, is probably of limited occurrence in deformed pelitic rocks. A second deformation sequence considered the superposition of pre-tectonic compaction and tectonic strain consisting of initial layer-parallel shortening followed by layer-parallel shear (related to flexural folding). Also in this instance, volume change during tectonic deformation and tectonic plane strain have been assumed. For geologically reasonable amounts of volume loss due to compaction and of initial layer-parallel shortening, this type of deformation history is capable of producing a deformation path entirely lying within the oblate strain field, but still characterized by a changeover, during deformation, of the maximum extension axis (X) from a position parallel to the fold axis to one perpendicular to it. This type of deformation sequence may explain the main strain features observed in the study area, where most of the measured finite strain ellipsoids, determined from the limb regions of flexural folds, display an oblate shape, irrespective of the orientation of their maximum extension direction (X) with respect to the local structural trends. More generally, this type of deformation history provides a mechanism to account for the predominance of oblate strains in deformed pelitic rocks.     

云南大地热流及地热地质问题

本文报道了云南20多个大地热流测试数据。据热流分布特点并参考前人有关资料,结合地球物理测深资料、岩石热物性与放射性生热率测试数据,对各区地壳深度范围的温度、热流配分组成作了粗略分析,划分出各有特征的若干地质-热流区。云南普遍地热偏高(滇东南小范围除外)的主要原因是新构造运动强烈;怒江以西近代岩浆活动亦强烈,具有典型的板块交汇带的基本地热特点     

Some breakage characteristics of ultra-fine wet grinding with a centrifugal mill

A centrifugal mill is a high-power intensity media mill that can be used for ultra-fine grinding, employing centrifugal forces generated by gyration of the axis of the mill tube in a circle. The mill charge motion is quite different depending on the ratio of the gyration diameter to the mill diameter (G / D ratio), varying from a motion similar to that of a conventional tumbling media mill to that of a vibration mill. In this study, a centrifugal mill was constructed with an arrangement where the gyration diameter could be readily adjusted. The batch grinding characteristics of three different minerals (limestone, talc and illite) in water with dispersing agent were investigated at various G / D ratios. It was found that the optimum G / D ratio in terms of the specific energy consumption to give a desired fineness of product was different for the three minerals. This was due to their different reactions to the breakage mechanisms provided by the mill charge motion at varying G / D ratios. The size distributions became progressively narrower at increased grinding times, and particles finer than about 0.1 μm were not detected even for prolonged grinding times. Measurement of specific surface areas indicated that this was not due to an artifact of the size measurements by laser diffractometry. This implies that there is a limitation in which particles finer than 0.1 μm are not produced under the conditions tested in this type of mill, but further investigation is needed for experimental verification of this limit of comminution.     

Reservoir description using dynamic parameterisation selection with a combined stochastic and gradient search

There is a correspondence between flow in a reservoir and large scale permeability trends. This correspondence can be derived by constraining reservoir models using observed production data. One of the challenges in deriving the permeability distribution of a field using production data involves determination of the scale of resolution of the permeability. The Adaptive Multiscale Estimation (AME) seeks to overcome the problems related to choosing the resolution of the permeability field by a dynamic parameterisation selection. The standard AME uses a gradient algorithm in solving several optimisation problems with increasing permeability resolution. This paper presents a hybrid algorithm which combines a gradient search and a stochastic algorithm to improve the robustness of the dynamic parameterisation selection. At low dimension, we use the stochastic algorithm to generate several optimised models. We use information from all these produced models to find new optimal refinements, and start out new optimisations with several unequally suggested parameterisations. At higher dimensions we change to a gradient-type optimiser, where the initial solution is chosen from the ensemble of models suggested by the stochastic algorithm. The selection is based on a predefined criterion. We demonstrate the robustness of the hybrid algorithm on sample synthetic cases, which most of them were considered insolvable using the standard AME algorithm.     

The distribution of radiogenic heat production as a function of depth in the Sierra Nevada Batholith, California

Geochemical analyses and geobarometric determinations have been combined to create a depth vs. radiogenic heat production database for the Sierra Nevada batholith, California. This database shows that mean heat production values first increase, then decrease, with increasing depth. Heat production is 2 μW/m³ within the 3-km-thick volcanic pile at the top of the batholith, below which it increases to an average value of 3.5 μW/m³ at 5.5 km depth, then decreases to 0.5–1 μW/m³ at 15 km depth and remains at these values through the entire crust below 15 km. Below the crust, from depths of 40–125 km, the batholith's root and mantle wedge that coevolved beneath the batholith appears to have an average radiogenic heat production rate of 0.14 μW/m³. This is higher than the rates from most published xenolith studies, but reasonable given the presence of crustal components in the arc root assemblages. The pattern of radiogenic heat production interpreted from the depth vs. heat production database is not consistent with the downward-decreasing exponential distribution predicted from modeling of surface heat flow data. The interpreted distribution predicts a reasonable range of geothermal gradients and shows that essentially all of the present day surface heat flow from the Sierra Nevada could be generated within the 35 km thick crust. This requires a very low heat flux from the mantle, which is consistent with a model of cessation of Sierran magmatism during Laramide flat-slab subduction, followed by conductive cooling of the upper mantle for 70 m.y. The heat production variation with depth is principally due to large variations in uranium and thorium concentration; potassium is less variable in concentration within the Sierran crust, and produces relatively little of the heat in high heat production rocks. Because silica content is relatively constant through the upper 30 km of the Sierran batholith, while U, Th, and K concentrations are highly variable, radiogenic heat production does not vary directly with silica content.     

A Decision Support System for the Evaluation of Eco-engineering Strategies for Slope Protection

A decision support system (DSS) has been developed to assist expert and non-expert users in the evaluation and selection of eco-engineering strategies for slope protection. This DSS combines a qualitative hazard assessment of erosion and mass movements with a detailed catalogue of eco-engineering strategies for slope protection of which the suitability is evaluated in relation to the data entered. The slope decision support system (SDSS) is a knowledge based DSS in which knowledge is stored in frames containing rules that can evaluate the available information for a project, stored as project specific information (PSI) in a data file. The advantages of such a system are that it accepts incomplete information and that the qualitative nature of the information does not instil the user with a sense of unjustified exactitude. By its multidisciplinary and progressive nature, the DSS will be of value during the initial stages of an eco-engineering project when data collection and the potential of different eco-engineering strategies are considered. The accent of the output of the DSS is on the application of eco-engineering strategies for slope protection as an environmentally-friendly solution aiding sustainable development. For its acceptance within the engineering community, the DSS needs to prove its predictive capacity. Therefore, its performance has been benchmarked against successful and unsuccessful cases of slope stabilisation using eco-engineering. The target audience and the areas of application of this DSS are reviewed and the strategies for further development in this area suggested.