Numerical modelling of rise and fall of a dense layer in salt diapirs

Numerical models are used to study the entrainment of a dense anhydrite layer by a diapir. The anhydrite layer is initially horizontally embedded within a viscous salt layer. The diapir is down-built by aggradation of non-Newtonian sediments ( n = 4, constant temperature) placed on the top of the salt layer. Several parameters (sedimentation rate, salt viscosity, perturbation width and stratigraphic position of the anhydrite layer) are studied systematically to understand their role in governing the entrainment of the anhydrite layer. High sedimentation rates during the early stages of the diapir evolution bury the initial perturbation and, thus, no diapir forms. The anhydrite layer sinks within the buried salt layer. For the same sedimentation rate, increasing viscosity of the salt layer decreases the rise rate of the diapir and reduces the amount (volume) of the anhydrite layer transported into the diapir. Model results show that viscous salt is capable of carrying separate blocks of the anhydrite layer to relatively higher stratigraphic levels. Varying the width of the initial perturbation (in our calculations 400–800 m), from which a diapir triggers, shows that wider diapirs can more easily entrain an embedded anhydrite layer than the narrower diapirs. The anhydrite layer is entrained as long as rise rate of the diapir exceeds the descent rate of the denser anhydrite layer. We conclude that the four parameters mentioned above govern the ability of a salt diapir to entrain an embedded dense layer. However, the model results show that the entrained blocks inevitably sink back if the rise rate of the diapir is less than the rate of descent of the anhydrite layer or the diapir is permanently covered by a stiff overburden in case of high sedimentation rates.     

Thin elastic shells with variable thickness for lithospheric flexure of one-plate planets

Planetary topography can either be modelled as a load supported by the lithosphere, or as a dynamic effect due to lithospheric flexure caused by mantle convection. In both cases the response of the lithosphere to external forces can be calculated with the theory of thin elastic plates or shells. On one-plate planets the spherical geometry of the lithospheric shell plays an important role in the flexure mechanism. So far the equations governing the deformations and stresses of a spherical shell have only been derived under the assumption of a shell of constant thickness. However, local studies of gravity and topography data suggest large variations in the thickness of the lithosphere. In this paper, we obtain the scalar flexure equations governing the deformations of a thin spherical shell with variable thickness or variable Young's modulus. The resulting equations can be solved in succession, except for a system of two simultaneous equations, the solutions of which are the transverse deflection and an associated stress function. In order to include bottom loading generated by mantle convection, we extend the method of stress functions to include loads with a toroidal tangential component. We further show that toroidal tangential displacement always occurs if the shell thickness varies, even in the absence of toroidal loads. We finally prove that the degree-one harmonic components of the transverse deflection and of the toroidal tangential displacement are independent of the elastic properties of the shell and are associated with translational and rotational freedom. While being constrained by the static assumption, degree-one loads can deform the shell and generate stresses. The flexure equations for a shell of variable thickness are useful not only for the prediction of the gravity signal in local admittance studies, but also for the construction of stress maps in tectonic analysis.     

Numerical inversion of deformation caused by pressure sources: application to Mount Etna (Italy)

The interpretation of geodetic data in volcanic areas is usually based on analytical deformation models. Although numerical finite element (FE) modelling allows realistic features such as topography and crustal heterogeneities to be included, the technique is not computationally convenient for solving inverse problems using classical methods. In this paper, we develop a general tool to perform inversions of geodetic data by means of 3-D FE models. The forward model is a library of numerical displacement solutions, where each entry of the library is the surface displacement due to a single stress component applied to an element of the grid. The final solution is a weighted combination of the six stress components applied to a single element-source. The pre-computed forward models are implemented in a global search algorithm, followed by an appraisal of the sampled solutions. After providing extended testing, we apply the method to model the 1993–1997 inflation phase at Mt Etna, documented by GPS and EDM measurements. We consider four different forward libraries, computed in models characterized by homogeneous/heterogeneous medium and flat/topographic free surface. Our results suggest that the elastic heterogeneities of the medium can significantly alter the position of the inferred source, while the topography has minor effect.     

Quasi-static analysis of strike fault growth in layered media

We study the effects of structural inhomogeneity on the quasi-static growth of strike-slip faults. A layered medium is considered, made up of an upper layer bounded by a free surface and welded to a lower half-space with different elastic property. Mode III crack is employed as a mathematical model of strike-slip fault, which is nucleated in the lower half-space and then propagates towards the interface. We adopt FEM-β, newly proposed analysis method for failure, to simulate the quasi-statistic crack growth governed by the stress distribution in layered media. Our results show that along planar traces across interfaces a compliant upper layer has significant effects on promoting/suppressing crack growth before/after its extension into the layer and vice versa for a rigid one. This proposes a possibility that surface breaks due to strike-slip faulting could be arrested by deposit layers at the topmost part of the Earth's crust.     

Stable inversions for complete moment tensors

The seismic moment tensors for certain types of sources, such as volcanic earthquakes and nuclear explosions are expected to contain an isotropic component. Some earlier efforts to calculate the isotropic component of these sources are flawed due to an error in the method of Jost & Herrmann. We corrected the method after Herrmann & Hutchensen and found great improvement in the recovery of non-double-couple moment tensors that include an isotropic component. Tests with synthetic data demonstrate the stability of the corrected linear inversion method, and we recalculate the moment tensor solutions reported in Dreger et al. for Long Valley caldera events and Dreger & Woods for Nevada Test Site nuclear explosions. We confirm the findings of Dreger et al. that the Long Valley volcanic sources contain large statistically significant isotropic components. The nuclear explosions have strikingly anomalous source mechanisms, which contain very large isotropic components, making it evident that these events are not tectonic in origin. This indicates that moment tensor inversions could be an important tool for nuclear monitoring.