A seismic source zone model for the seismic hazard assessment of the Italian territory

We designed a new seismic source model for Italy to be used as an input for country-wide probabilistic seismic hazard assessment (PSHA) in the frame of the compilation of a new national reference map.

We started off by reviewing existing models available for Italy and for other European countries, then discussed the main open issues in the current practice of seismogenic zoning.

The new model, termed ZS9, is largely based on data collected in the past 10 years, including historical earthquakes and instrumental seismicity, active faults and their seismogenic potential, and seismotectonic evidence from recent earthquakes. This information allowed us to propose new interpretations for poorly understood areas where the new data are in conflict with assumptions made in designing the previous and widely used model ZS4.

ZS9 is made out of 36 zones where earthquakes with M_w > = 5 are expected. It also assumes that earthquakes with M_w up to 5 may occur anywhere outside the seismogenic zones, although the associated probability is rather low. Special care was taken to ensure that each zone sampled a large enough number of earthquakes so that we could compute reliable earthquake production rates.

Although it was drawn following criteria that are standard practice in PSHA, ZS9 is also innovative in that every zone is characterised also by its mean seismogenic depth (the depth of the crustal volume that will presumably release future earthquakes) and predominant focal mechanism (their most likely rupture mechanism). These properties were determined using instrumental data, and only in a limited number of cases we resorted to geologic constraints and expert judgment to cope with lack of data or conflicting indications. These attributes allow ZS9 to be used with more accurate regionalized depth-dependent attenuation relations, and are ultimately expected to increase significantly the reliability of seismic hazard estimates.     

Mapping Proterozoic unconformity-related uranium deposits in the Rockhole area, Northern Territory, Australia using landsat ETM+

The Rockhole area, Northern Territory, Australia, hosts a number of Proterozoic unconformity-related uranium deposits. The geology of the area features within Paleoproterozoic rocks of the Pine Creek Orogen, near the unconformity with overlying platform cover sandstone of the Paleo- to Mesoproterozoic McArthur Basin. Landsat Enhanced Thematic Mapper plus (ETM+) data was used in the Rockhole area to assist in mapping geological structures and lithology, and to identify anomalous concentrations of ferrous minerals, the product of alteration, which can be indicators of buried uranium mineralization. Several image-processing procedures were applied to the ETM+ data to identify, isolate and enhance mineralogical information as simple and complex false color composites. ETM+ 754 shown as red green and blue respectively was the best simple image. Overall, complex images based on Principal Component Analysis proved to be the most useful products. Sandstone, shale and siltstone, the target lithologies, Koolpin Formation, the target stratigraphic unit, and bleaching pattern due to the removal of iron(II) compounds, the target alteration pattern, were confidently mapped to provide information required by the mineral emplacement model, which ultimately identified areas of likely uranium mineralization. Thus the contrasting behavior of the two principle oxidation states of uranium and iron can be utilized to map/delineate bleached alteration zones associated with economic concentrations of uranium using multispectral sensors like Landsat or better hyperspectral sensors.     

Application of MODFLOW and geographic information system to groundwater flow simulation in North China Plain, China

MODFLOW is a groundwater modeling program. It can be compiled and remedied according to the practical applications. Because of its structure and fixed data format, MODFLOW can be integrated with Geographic Information Systems (GIS) technology for water resource management. The North China Plain (NCP), which is the politic, economic and cultural center of China, is facing with water resources shortage and water pollution. Groundwater is the main water resource for industrial, agricultural and domestic usage. It is necessary to evaluate the groundwater resources of the NCP as an entire aquifer system. With the development of computer and internet information technology it is also necessary to integrate the groundwater model with the GIS technology. Because the geological and hydrogeological data in the NCP was mainly in MAPGIS format, the powerful function of GIS of disposing of and analyzing spatial data and computer languages such as Visual C and Visual Basic were used to define the relationship between the original data and model data. After analyzing the geological and hydrogeological conditions of the NCP, the groundwater flow numerical simulation modeling was constructed with MODFLOW. On the basis of GIS, a dynamic evaluation system for groundwater resources under the internet circumstance was completed. During the process of constructing the groundwater model, a water budget was analyzed, which showed a negative budget in the NCP. The simulation period was from 1 January 2002 to 31 December 2003. During this period, the total recharge of the groundwater system was 49,374 × 10⁶ m³ and the total discharge was 56,530 × 10⁶ m³ the budget deficit was −7,156 × 10⁶ m³. In this integrated system, the original data including graphs and attribution data could be stored in the database. When the process of evaluating and predicting groundwater flow was started, these data were transformed into files that the core program of MODFLOW could read. The calculated water level and drawdown could be displayed and reviewed online.     

Flood hazard delineation combining geomorphological and hydrological methods: an example in the Northern Iberian Peninsula

Flood mapping requires the combination and integration of geomorphological and hydrological-hydraulic methods; however, despite this, there is very little scientific literature that compares and validates both methods. Two types of analysis are addressed in the present article. On the one hand, maps of flood plains have been elaborated using geomorphological evidence and historical flood data in the mountainous area of northwestern Spain, covering an area of more then 232 km² of floodplains. On the other hand, a hydrometeorological model has been developed (Clark semidistributed unit hydrograph) in the Sarria River basin (155 km², NW Spain). This basin is not gauged, hence the model was subjected to a goodness-of-fit test of its parameter (curve number) by means of Monte Carlo simulation. The peak flows obtained by means of the hydrological model were used for hydraulic modeling (one-phase, one-dimensional and steady flow) in a 4 km² urban stretch of the river bed. The delineation of surface areas affected by floods since 1918, as well as those analyzed subsequent to the geomorphological study, reveals a high degree of reliability in the delineation of the flooded areas with frequent recurrence intervals (<50 years). If we compare these flooded surface areas with the estimate obtained by the hydrological-hydraulic method we can see that the latter method overestimates the extent of the surface water by 144% for very frequent recurrence intervals (>10 years) and underestimates it as the recurrence interval increases, by up to 80% less floodplain for exceptional events (>500 years). Finally, a management map is put forth combining the most reliable results available by integrating both methods. Originally presented at the Sixth International Conference on Geomorphology.     

Numerical modeling of tide-surge interaction along Orissa coast of India

The Orissa coast of India is one of the most vulnerable regions of extreme sea levels associated with severe tropical cyclones. There was extensive loss of life and property due to the October 1999 super cyclone, which devastated large part of the Orissa coast. The shallow nature of the head bay, presence of a large number of deltas formed by major rivers of Orissa such as Mahanadi and Dhamra, and high tidal range are responsible for storm surge flooding in the region. Specifically, rising and falling tidal phases influence the height, duration, and arrival time of peak surge along the coast. The objective of the present study is to evaluate the tide-surge interaction during the 1999 Orissa cyclone by using nonlinear vertically integrated numerical models. The pure tidal solution for the head bay region of the Bay of Bengal provides the initial condition for the fine resolution nested grid Orissa model. However, the feedback from the Orissa model does not affect the head bay model as the study provides a one-way interaction. Numerical experiments are performed to study the tide-surge interaction by considering various relative phases of the tidal waves with the surge-wave produced by 1999 Orissa cyclone. The comparison, although utilizing only the limited estimates of tidal data, appears adequate to assert that the principal features are reproduced correctly.     

Contribution of the SISCam Web-based GIS to the seismotectonic study of Campania (Southern Apennines): an example of application to the Sannio-area

In this article the implementation and potential of the Seismotectonic Information System of the Campania Region (SISCam) are described, in particular an application of this Web-based GIS system to the seismotectonic analysis of the Sannio area (Southern Apennines) is performed. WEB-GIS technologies greatly contribute to both the environmental monitoring and the disaster management of areas affected by high natural risks. Specifically the SISCam system has been developed with the aim of providing easy access and fast diffusion, through Internet technology, of the most significant geological, geophysical, and territorial data relative to the Campania Region. The Sannio area has been selected as our application example because it is among the most active seismic regions in Italy. This portion of the Southern Apennines which was hit by the June 5, 1688 strong earthquake (M _W = 6.7, CPTI 1999) and by some low- and moderate-energy seismic sequences (1990–1992, 1997), is characterized by a complex inherited tectonic setting and low-tectonic deformation rates that hide the seismogenic sources position. Since this case study turned out to be complicated, the use of the SIScam WEB-GIS has become indispensable because it allowed us to visualize, integrate and analyze all the data available, in order to obtain an accurate and direct picture of the seismotectonic setting of the area. Moreover, a different approach of data analysis was necessary, due to the lack of up-to-date neotectonic and structural data; therefore, the operation of this GIS system enabled us to process and generate some original informative layers, through image analysis, such as new structural lineaments represented on a map of the potential active faults of the area, which has been the final result of our application, as a contribution to new knowledge about the local seismic risk parameters.     

Ground motion estimation during the Kashmir earthquake of 8th October 2005

In this article, analytical methods have been used to estimate ground motion during the 8 October 2005, Kashmir earthquake. Peak ground acceleration (PGA) values at several stations in the epicentral region have been estimated by empirical analytical source mechanism models. As an alternate analysis, PGA estimates have also been obtained using the stochastic finite fault seismological model. The estimated PGAs are compared with that obtained from damage values. A PGA contour map in the near-source region is provided. It is found that very near to the epicenter, PGA would have reached more than 1 g. It is demonstrated that empirical analytical models can be effectively used to estimate ground motion due to rupture of active faults.     

滑坡体三维地质建模与可视化分析

针对滑坡地质研究的自身特点,提出了面向滑坡地质体三维建模的NURBS-BRep混合数据结构和地质结构单元实体构造技术.通过对滑坡基础地质数据的预处理、滑坡数字地形和滑动面的三维建模、地质结构面的系统构造、地质结构体的生成和显示,形成了一套完整的滑坡三维地质模型的构建方法.将该方法应用于某水库滑坡,建立了相应的三维滑坡地质模型,并基于此模型进行了三维剖切分析、数字钻孔、等值线生成、滑块自动剖分、滑坡失稳可视化动态模拟和滑坡体方量精确计算等一系列实用的可视化分析,为滑坡稳定性的准确计算和客观评价提供了有力的支持.     

基于Mindlin理论Winkler地基参数的Kalman滤波识别

提出了Winkler地基参数的Kalman滤波识别方法。引入Mindlin理论后,推导了Winkler地基上板的控制微分方程。利用Fourier变换,推求了Winkler地基上简支板的Fourier闭式解。推导了Winkler地基参数的Kalman滤波方程,研究了Winkler地基参数的Kalman滤波识别的具体计算步骤。研究表明,运用Kalman滤波理论进行Winkler地基参数的识别,能有效地估计Winkler地基参数;Winkler地基参数的滤波收敛速度和精度受地基参数初始值选取和位移实测资料的影响,且Kalman滤波理论也可用于其他地基模型地基参数的识别。