影像匹配中几种相似性测度的分析

对基于灰度影像匹配中的几种相似性测度进行了研究，分析了每种测度的直观意义、限制条件以及改进措施，最后通过实验结果验证了上述结论。     

无拓扑矢量数据快速压缩算法的研究与实现

首先论述传统矢量数据压缩算法：道格拉斯—普克法，分析将其应用于多边形边界数据压缩所造成的图形失真现象，在此基础上提出一种针对无拓扑矢量数据的快速压缩算法，并在MapInfo环境中实现该算法。     

Measuring the k–S–p relations on DNAPLs migration

Migration characteristics of dense non-aqueous phase liquids (DNAPLs) in the subsurface can be expressed as a water–DNAPL two-phase system based on mainly the k–S–p relations, which describe the relations among relative permeability (k), degree of water saturation (S), and capillary pressure head (p). The aims of this research are to develop an experimental system with new type of probes, such as the electrical conductivity probe for measuring the degree of water saturation and the hydrophilic and hydrophobic tensiometer for measuring the pore water and DNAPL pressures, and also to estimate the results obtained from the developed experimental system. From these tests, the excellent k–S–p relations were obtained and the efficiency and validity of this developed experimental system have been confirmed in terms of the concept of the scaling coefficient calculated by interfacial tensions.     

Quantifying Storm Tide Risk in Cairns

The United Nations International Decade for Natural Disaster Reduction (IDNDR)gave rise to an increasing level of attention to the risks posed by a range of naturalhazards and the development of strategies by which to reduce those risks. It waswidely recognised that in order to evaluate risk treatment strategies it was necessaryto `measure' the level of risk that already existed and the level of risk that would beencountered with the treatment strategy(s) in place.This paper outlines the methodology developed under the AGSO (now GeoscienceAustralia) Cities Project to quantify the risk associated with storm tide inundation. It includes the methodology for `measuring' the level of community exposure to storm tide hazards and the methodology for `measuring' community vulnerability. The Far North Queensland city of Cairns is used as the case study to demonstrate the application of these methods.     

Stepwise Conditional Transformation for Simulation of Multiple Variables

Most geostatistical studies consider multiple-related variables. These relationships often show complex features such as nonlinearity, heteroscedasticity, and mineralogical or other constraints. These features are not handled by the well-established Gaussian simulation techniques. Earth science variables are rarely Gaussian. Transformation or anamorphosis techniques make each variable univariate Gaussian, but do not enforce bivariate or higher order Gaussianity. The stepwise conditional transformation technique is proposed to transform multiple variables to be univariate Gaussian and multivariate Gaussian with no cross correlation. This makes it remarkably easy to simulate multiple variables with arbitrarily complex relationships: (1) transform the multiple variables, (2) perform independent Gaussian simulation on the transformed variables, and (3) back transform to the original variables. The back transformation enforces reproduction of the original complex features. The methodology and underlying assumptions are explained. Several petroleum and mining examples are used to show features of the transformation and implementation details.     

The anisotropy of magnetic susceptibility in biotite, muscovite and chlorite single crystals

The anisotropy of magnetic susceptibility (AMS) of single crystals of biotite, muscovite and chlorite has been measured in order to provide accurate values of the magnetic anisotropy properties for these common rock-forming minerals. The low-field AMS and the high-field paramagnetic susceptibility are defined. For the high-field values, it is necessary to combine the paramagnetic deviatoric tensor obtained from the high-field torque magnetometer with the paramagnetic bulk susceptibility measured from magnetization curves of the crystals. This leads to the full paramagnetic susceptibility ellipsoid due to the anisotropic distribution of iron cations in the silicate lattice. The ellipsoid of paramagnetic susceptibility, which was obtained for the three phyllosilicates, is highly oblate in shape and the minimum susceptibility direction is subparallel to the crystallographic c-axes. The anisotropy of the susceptibility within the basal plane of the biotite has been evaluated and found to be isotropic within the accuracy of the instrumental measurements. The degree of anisotropy of biotite and chlorite is compatible with previously reported values while for muscovite the smaller than previously published values. The shape of the chlorite AMS ellipsoid for all the samples is near-perfect oblate in contrast with a wide distribution of oblate and prolate values reported in earlier studies. Reliable values are important for deriving models of the magnetic anisotropy where it reflects mineral fabrics and deformation of rocks.     

兴山县龙王嘴边坡稳定性分析与加固设计

龙王嘴边坡系坡高达70 m、坡角达70 °的高陡岩质边坡。分析了宜-秭公路石峡段龙王嘴高边坡变形的地质条件,在定量评价龙王嘴高边坡稳定性的基础上,进行了该高边坡的施工图加固设计。根据其特点将350 m长的坡段分为A,B,C三个区,分别采取预应力锚索与锚杆加固、挂网喷射混凝土支护和喷射混凝土支护等措施,实践证明,工程治理效果良好。     

Researches on Cartographic Database-Based Interactive Three-Dimensional Topographic Map

With the development of computer graphics, the three-dimensional (3D) visualization brings new technological revolution to the traditional cartography. Therefore, the topographic 3D-map emerges to adapt to this technological revolution, and the applications of topographic 3D-map are spread rapidly to other relevant fields due to its incomparable advantage. The researches on digital map and the construction of map database offer strong technical support and abundant data source for this new technology, so the research and development of topographic 3D-map will receive greater concern. The basic data of the topographic 3D-map are rooted mainly in digital map and its basic model is derived from digital elevation model (DEM) and 3D-models of other DEM-based geographic features. In view of the potential enormous data and the complexity of geographic features, the dynamic representation of geographic information becomes the focus of the research of topographic 3D-map and also the prerequisite condition of 3D query and analysis. In addition to the equipment of hardware that are restraining, to a certain extent, the 3D representation, the data organization structure of geographic information will be the core problem of research on 3D-map. Level of detail (LOD). space partitioning, dynamic object loading (DOL) and object culling are core technologies of the dynamic 3D representation. The objectselection, attribute-query and model-editing are important functions and interaction tools for users with 3D-maps provided by topographic 3D-map system, all of which are based on the data structure of the 3D-model. This paper discusses the basic theories, concepts and cardinal principles of topographic 3I)-map,expounds the basic way to organize the scene hierarchy of topographic 3D-map based on the node mechanism and studies the dynamic representation technologies of topographic 3D-map based on LOD, space partitioning, DOL and object culling. Moreover. such interactive operation functions are explored, in this paper, as spatial query, scene editing and management of topographic 3D-map. Finally, this paper describes briefly the applications of topographic 3D-map in its related fields.     

变形体的稳定性及其定量分析方法初探

变形体的稳定性是变形体性质的重要内容，它是工程实际中极为关注的问题，但从变形监测的角度上来分析变形的稳定性目前在国内外还未见任何实质性的报导。本文讨论了从变形监测角度上分析变形体稳定性的一般方法，进行变形稳定性的分类，初步研究了变形体稳定性的定量分析方法，定义了一系列量化指标，如稳定度、因素的影响域与因素的稳定域等。这些有利于把稳定性分析推向应用和深入，从而提高变形监测在变形体定性分析中的地位，增