基于NGM(1,1,k,c)模型和改进切线角的危岩变形预测

针对危岩变形预测问题,本文以非齐次指数序列的灰色模型(NGM)作为危岩变形预测的基本模型,通过对望霞危岩变形的分析结果显示,NGM(1,1,k,c)模型拟合效果明显优于GM(1,1)模型,说明危岩变形趋势更接近于非齐次指数序列。利用NGM(1,1,k,c)模型结合改进切线角可对危岩变形趋势进行分析预测,可作为危岩稳定性和发展趋势的评估依据。     

关于制作像控电子点之记方法与流程的探讨

主要介绍电子点之记的制作流程及方法,以及所涉及的一些计算机软件和工序中可以自动化处理的程序,对于实现难点也进行了分析及说明,使像片控制测量点之记制作的流程更为简便,成果更为可靠。     

地理国情各要素之间套合关系检查要点分析

将地理国情普查工作中地表覆盖和地理国情要素两个重要成果之间的套合关系进行梳理,依据各项规定和生产实践经验,对重点问题进行整理和分析,明确了两者相互关系并提供一些有益的建议,为提高地理国情普查成果质量提供帮助。     

1∶10000图库一体化数据的质量控制

根据1∶10 000图库一体化数据成果,对图库一体化数据生产过程中各个环节的质量控制进行探讨,提出了一体化数据的质量控制方法。     

土地变更影像在棚户区改造资金监管中的应用探索

加快棚户区改造是落实国务院部署的一项政治任务,也是当前及今后一段时期内的最大民生工程。通过利用年度土地变更调查遥感影像对荣成市2015年度棚户区改造新开工项目进行甄别排查,经实地核查后获取不合格项目的具体范围和面积。研究结果表明,利用年度土地变更调查遥感影像可以有效地提高棚户区改造资金监管中对于项目定性效率,并推进资源共享共建,为政府决策提供科学依据。     

基于UCD数码影像在1∶10000地形图生产中像控点布设方案的研究及精度分析

叙述了在1∶10 000地形图生产中,通过设立试验区,在进行全野外布点的基础上,采用UCD数码影像在无POS辅助和有POS辅助两种情况下,使用自动空中三角测量软件Geolord-AT进行加密的方法。论证了区域网的大小对精度的影响,并通过精度分析,确定像控点布设方法,可为相似航测项目像控点布设方案的确定提供参考。     

某双向混凝土立交桥顶推法施工控制测量

文中所选立交桥为双向三车道桥梁,单幅为3跨105 m的箱型连续梁,重量3 400 t,横跨铁路线。对于跨铁路的桥梁建设,顶推法施工可最大限度地减少对交通的影响。桥梁重量大,所须牵引力约280 t,施工过程中对桥墩及其他建筑物产生的变形较大,施工前模拟施工状态,设计控制测量监控的基本方案,利用控制测量方法,对施工状态实时监测,预测变形及偏位、纠偏,使施工状态最大限度地接近理想状态。顶推到位后,轴向偏位满足1 cm的限差,桥墩变形基本满足施工规范的要求,最终顺利完成顶推过程。     

求解GM(1,1)模型新总体最小二乘算法

在GM(1,1)模型中系数矩阵和观测向量都是由原始序列组成的。系数矩阵中同样是有误差的,与观测向量中的误差一样,亦来源于原始序列,即它们误差同源。不同位置的相同元素应该有相同的改正数,采用传统总体最小二乘求解则不能达到此目的。针对这一缺陷,推导了一种新的总体最小二乘算法;并且通过算例验证了新方法的可行性和有效性。     

Autogenic avulsion,channelization and backfilling dynamics of debris‐flow fans

Alluvial fans develop their semi‐conical shape by quasi‐cyclic avulsions of their geomorphologically active sector from a fixed fan apex. On debris‐flow fans, these quasi‐cyclic avulsions are poorly understood, partly because physical scale experiments on the formation of fans have been limited largely to turbidite and fluvial fans and deltas. In this study, debris‐flow fans were experimentally created under constant extrinsic forcing, and autogenic sequences of backfilling, avulsion and channelization were observed. Backfilling, avulsion and channelization were gradual processes that required multiple successive debris‐flow events. Debris flows avulsed along preferential flow paths given by the balance between steepest descent and flow inertia. In the channelization phase, debris flows became progressively longer and narrower because momentum increasingly focused on the flow front as flow narrowed, resulting in longer run‐out and deeper channels. Backfilling commenced when debris flows reached their maximum possible length and channel depth, as defined by channel slope and debris‐flow volume and composition, after which they progressively shortened and widened until the entire channel was filled and avulsion was initiated. The terminus of deposition moved upstream because the frontal lobe deposits of previous debris flows created a low‐gradient zone forcing deposition. Consequently, the next debris flow was shorter which led to more in‐channel sedimentation, causing more overbank flow in the next debris flow and resulting in reduced momentum to the flow front and shorter runout. This topographic feedback is similar to the interaction between flow and mouth bars forcing backfilling and transitions from channelized to sheet flow in turbidite and fluvial fans and deltas. Debris‐flow avulsion cycles are governed by the same large‐scale topographic compensation that drives avulsion cycles on fluvial and turbidite fans, although the detailed processes are unique to debris‐flow fans. This novel result provides a basis for modelling of debris‐flow fans with applications in hazards and stratigraphy.     

Flexible membranes anchored to the ground for slope stabilisation: Numerical modelling of soil slopes using SPH

An alternative modelling for flexible membranes anchored to the ground for soil slope stabilisation is presented using Smoothed-Particle Hydrodynamics to model the unstable ground mass in a soil slope, employing a dynamic solve engine. A regression model of pressure normal to the ground, q_sim, and also membrane deflection, f_sim, have been developed using Design of Experiment. Finally, a comparison between the pressure obtained from numerical simulation and from a limit equilibrium analysis considering infinite slope has been carried out, showing differences in the results, mainly due to the membrane stiffness.