建筑在强震下横拉承压力钢筋负荷测量

在强震状态下,建筑物的横拉承压受力较为复杂,另外由于建筑物形状及在地震中受力面积大小不同,在强震下造成碰撞大小影响不一导致其横拉承压力的随机复杂性十分突出。传统的建筑承压负荷检测方法中钢筋负荷受力测量能力不足,检测结果易出现误差。将建筑钢筋的机械性能设为理想弹塑性,利用建筑物横拉承压力钢筋负荷测量方法,对不同结构、不同工况的建筑钢筋载荷的变化规律进行测试分析,结合建筑局部承压特点和整体结构聚力方式,设计横拉承压力钢筋负荷检测方法,并进行仿真实验,结果表明该方法模型所得数据更加精准,有良好的适用性。     

Response of hybrid isolation system during a shake table experiment of a full‐scale isolated building

A full‐scale 5‐story steel moment frame building was subjected to a series of earthquake excitations using the E‐Defense shake table in August, 2011. For one of the test configurations, the building was seismically isolated by a hybrid system of lead‐rubber bearings and low friction roller bearings known as cross‐linear bearings, and was designed for a very rare 100 000‐year return period earthquake at a Central and Eastern US soil site. The building was subject to 15 trials including sinusoidal input, recorded motions and simulated earthquakes, 2D and 3D input, and a range of intensities including some beyond the design basis level. The experimental program was one of the first system‐level full‐scale validations of seismic isolation and the first known full‐scale experiment of a hybrid isolation system incorporating lead‐rubber and low friction bearings. Stable response of the hybrid isolation system was demonstrated at displacement demands up to 550 mm and shear strain in excess of 200%. Torsional amplifications were within the new factor stipulated by the code provisions. Axial force was observed to transfer from the lead‐rubber bearings to the cross‐linear bearings at large displacements, and the force transfer at large displacements exceeded that predicted by basic calculations. The force transfer occurred primarily because of the flexural rigidity of the base diaphragm and the larger vertical stiffness of the cross‐linear bearings relative to the lead‐rubber bearings.     

车辆荷载作用下山西路基重塑黄土的动力特性研究

针对车辆荷载对山西高速公路路基土体影响研究不足的现状,从试验角度出发,研究车辆荷载水平、波形、干密度和围压对路基土体的动力特性响应。研究表明:路基土体的体变随波形比的增大而增大,随车辆荷载的增大而增大;路基土体的动弹性模量随干密度的增大而增大,随围压的增大而增大,阻尼比随围压的增大而减小。     

Bed-load transport rate based on the entrainment probabilities of sediment grains by rolling and lifting

A function for the bed-load sediment transport rate is derived. This function is obtained by using the entrainment probabilities of the rolling and lifted sediment grains, and by introducing two travel lengths, respectively. The predictions from the new bed-load function agree well with experimental results over the entire experimental range and show significant improvement over the commonly used formula for the bed-load transport rate. The new function shows that, in terms of contributing to the bed-load transport rate, the total entrainment probability of the sediment grains is a weighted summation of those for the lifted and rolling grains, rather than a simple addition of the two. The function is also used to predict the total entrainment probability, saltation length, and the bed layer thickness at a high bed-load transport rate. These predictions all agree well with the experimental results. It is found that, on average, the travel length for the rolling sand grains is about an order of magnitude less than that of the lifted grains.     

Enhanced bed load sediment transport by unsteady flows in a degrading channel

Laboratory flume experiments were done to investigate bed load sediment transport by both steady and unsteady flows in a degrading channel. The bed, respectively composed of uniform sand, uniform gravel, or sand-gravel mixtures, always undergoes bulk degradation. It is found that both uniform and non-uniform bed load transport is enhanced greatly by unsteady flows as compared to their volume-equivalent steady flows. This enhancement effect is evaluated by means of an enhancement factor, which is shown to be larger with a coarser bed and lower discharges. Also, the fractional transport rates of gravel and sand in non-uniform sand-gravel mixtures are compared with their uniform counterparts under both steady and unsteady flows. The sand is found to be able to greatly promote the transport of gravel, whilst the gravel considerably hinders the transport of sand. Particularly, the promoting and hindering impacts are more pronounced at lower discharges and tend to be weakened by flow unsteadiness.     

信阳地震台水管倾斜仪加速E倾变化分析

信阳地震台水管倾斜仪EW分量2016年5月出现加速E倾变化,为确定异常性质及产生原因,从观测洞室环境、仪器观测系统、气象数据、环境干扰等进行调查,并采用有限元法和不规则荷载模型,计算台站附近的信阳林业学校拆迁荷载变化对水管倾斜仪观测的影响,最终判定本次异常为林校拆迁所致。     

基于多项式拟合均匀荷载面曲率曲线的结构损伤识别方法

为仅利用结构损伤状态的柔度矩阵对结构进行损伤程度识别,先对损伤状态的均匀荷载面曲率曲线进行最小二乘法拟合。根据曲率曲线差判断结构的损伤位置,对损伤位置的点进行剔除后,再利用未损伤位置上的点进行局部最小二乘法拟合,代替损伤前的均匀荷载面曲率曲线,用于结构的损伤定位与定量。通过一简支梁数值算例,先以理论的二次多项式进行拟合,考虑单损伤和多损伤的情况,进行损伤识别分析,再分析多项式次数、测点数目以及不同噪声水平对损伤定量精度的影响。结果表明:在一定范围内,次数越高拟合误差越小,但差别不明显,采用理论的二次多项式拟合即可满足结构损伤识别要求,无噪声的情况下,测点数目减半不影响损伤识别的精度,该方法具有一定的抗噪声能力。     

自由段先注浆对预应力锚索抗拔试验结果影响研究

为了解决无法采用已注浆锚索进行抗拔试验问题,基于界面脱黏剪切模型,利用荷载传递和弹性变形理论,考虑锚索锚固段与自由段长度比Lb /La的影响,建立了采用自由段已注浆锚索抗拔试验结果评价锚索抗拔性能的方法。结果表明：自由段注浆对锚索抗拔力有较大幅度的提高,尤其是当界面剪切阶段由弹性向脱黏过渡时,提高比例快速增加,并在脱黏后逐渐趋于稳定。其次,锚索自由段与锚固段交界面处剪切位移和轴力最大,并向两端逐渐降低。随着拉拔力的提高,界面剪切位移和轴力都不断增大,同时向锚索两端的衰减速度也加快。此外,弹性阶段时剪应力曲线为山峰型,而脱黏阶段为马鞍型,并随抗拔力的提高,马鞍开口逐渐扩大。最后,锚固段与自由段长度比Lb /La对锚索极限抗拔力的影响较小,其极限抗拔力折减系数?Q取值介于0.81～0.83之间,且Lb /La =2.5时,?Q计算值仅比实测结果小6.02%,验证了本文方法的可行性。     

竖向高荷载作用下大直径超长钻孔灌注桩承载性能试验

通过机场—西华高速大直径超长钻孔灌注桩大吨位竖向单桩静载试验,分析了该地区大直径超长钻孔灌注桩的承载性状以及荷载传递机理。试验结果表明:试桩的Q-S曲线呈缓变型,桩端承载力占总荷载的比例均<10%,即均表现为摩擦桩特性;试桩的侧摩阻力自上而下逐步发挥,侧摩阻力和桩端阻力异步发挥且互相耦合;大直径超长钻孔灌注桩桩侧摩阻力的发挥与土层性质、土层埋深及桩顶荷载水平有关;在高荷载作用下桩侧上部土层摩阻力具有不同程度的软化现象,而中下部土层侧摩阻力具有不同程度的强化现象,甚至即使在最大加载情况下,桩身下部土层的侧摩阻力也并未完全发挥,因此在根据规范计算超长桩承载力时,不同深度土层的侧摩阻力应乘以相应不同的修正系数。     

Soil resistances for laterally loaded rigid piles in multi-layered elastic soil

ABSTRACT

Short stubby piles like monopiles and large diameter drilled shafts undergo rigid body translation and rotation when subjected to a lateral force and/or a moment at the head. A method of analysis for these piles embedded in multi-layered elastic soil is developed using the variational principles of mechanics. Using this analysis, the soil resistance against pile movement can be rigorously related to the soil elastic constants, and the pile head displacement and rotation can be quickly calculated. The equilibrium equations for pile and soil displacements are obtained using the principle of virtual work and solved using an iterative algorithm. Pile responses obtained from the analysis match well with those obtained from three-dimensional finite element analyses in which the same inputs of loads, geometry, and material properties are given. Based on the new analysis, fitted equations for soil resistance parameters are developed, which can be used to directly calculate the pile head displacement and rotation without the use of the iterative algorithm. Numerical examples are provided that demonstrate how the method can be used to analyse practical problems.