A new method of testing pile using dynamic P-S-curve made by amplitude of wave train

A new method of detecting the vertical bearing capacity for single-pile with high strain is discussed in this paper. A heavy hammer or a small type of rocket is used to strike the pile top and the detectors are used to record vibration graphs. An expression of higher degree of strain (deformation force) is introduced. It is testified theoretically that the displacement, velocity and acceleration cannot be obtained by simple integral acceleration and differential velocity when long displacement and high strain exist, namely when the pile phase generates a whole slip relative to the soil body. That is to say that there are non-linear relations between them. It is educed accordingly that the force P and displacement S are calculated from the amplitude of wave train and (dynamic) P-S curve is drew so as to determine the yield points. Further, a method of determining the vertical bearing capacity for single-pile is discussed. A static load test is utilized to check the result of dynamic test and determine the correlative constants of dynamic-static P(Q)-S curve. Foundation item: Key projects of the tenth Five-year Plan of Yunnan Province (documented Yunnan district [2002]54-02-02) and Geophysical Society of Yunnan Province.     

A new method for testing pile by sin- gle-impact energy and P-S curve

Introduction Through many year's practices by vast numbers of scientific and technological workers andefforts from all aspects, the dynamic testing method of high-low strain has formally entered intothe technical code of foundation pile test of construction at last (The Industry Standards of thePeople's Republic of China, 2003). The striking mode of the dynamic testing method of high strainis stipulated as hammer in the code, the striking of rocket can also be used. The latter is widely…     

Bearing capacity of rock over mined cavities in Nottingham

A significant geohazard is created in Nottingham, UK, by hundreds of man-made caves cut in the weak sandstone beneath the city centre. Stability of the caves has been assessed by a single full-scale loading test, by numerical modelling with FLAC and by physical modelling in plaster. For typical caves 4 m wide, bearing capacity of the rock roof rises from 2 MPa where it is 1 m thick to 8 MPa where 3 m thick. Stability decreases over wider caves and where the loading pad edge is over the edge of the cave. Numerical modelling of a very wide cave revealed the failure mechanisms and also showed that an internal support wall increased roof bearing capacity by 50%. Local building regulations that require 3-5 m of rock cover over the sandstone caves appear to be conservative. In stronger rocks, including karstic limestone, a guideline that cover thickness exceeds 70% of the cave width appears to be appropriate.     

Bearing capacity of unsaturated expansive soils

It is difficult to determine the bearing capacity of a foundation in unsaturated expansive soil, although this is most important. The bearing capacity of unsaturated expansive soil is related to the drying and wetting environment. Swelling pressure occurs when the soil volume change is constrained as an expansive soil is inundated. The expansive lateral pressure, induced by the swelling pressure is similar to the passive earth pressure. By considering the effect of the expansive lateral pressure in Terzaghi's bearing capacity formula, the bearing capacity of unsaturated expansive soil is derived. Because it is very difficult to measure suction in situ, the bearing capacity is expressed using the expansive lateral pressure offers a feasible approach to calculate the bearing capacity of a foundation in unsaturated expansive soil, when suction is not measured. Plate load tests to measure the bearing capacity in situ were performed for the foundation in natural soil and saturated soil immersed by water. The verification of the bearing capacity formulae presented in this paper is conducted by comparing the predicted results with the results of the plate load tests on unsaturated expansive soils in Handan and Bingxia, China.     

The structural role of Ti in aluminosilicate liquids in the glass transition range: insights from heat capacity and shear viscosity measurements

The shear viscosities and 1 bar heat capacities of glasses and melts along the 67mol% silica isopleth in the system SiO₂-Al₂O₃-Na₂O-TiO₂ have been determined in the temperature ranges 780-1140 K and 305-1090 K respectively. Anomalous behaviour of both these properties is observed for compositions rich in TiO₂ and/or Al₂O₃, an observation attributed to liquid-liquid phase separation followed by anatase crystallization. For samples which do not show anomalous behaviour, it is found that the partial molar heat capacity of the TiO₂ component previously determined in Al-free compositions reproduces our heat capacities to within 1.3%. Viscosity data show that addition of TiO₂ tends to increase viscosity and melt fragility at constant temperature. Furthermore, heat capacity and viscosity data may be combined within the framework of the Adam-Gibbs theory to extract values of the configurational entropy of the liquids and qualitative estimates of the variation of the average energy barrier to viscous flow. Configurational entropy at 900K is inferred to decrease upon addition of TiO₂, in contrast to previous results from Al-free systems. The compositional limit separating normal from anomalous behaviour, as well as the data for homogenous melts have been used to constrain the structural role of Ti in these samples. Our data are consistent with a majority of Ti in five-fold coordination associated with a titanyl bond, in agreement with previous spectroscopic studies. Furthermore, we find no evidence for a Ti-Al interaction in our samples, and we are led to the conclusion that Al and Ti are incompletely mixed, a hypothesis consistent with the observed reduction of configurational entropy upon addition of TiO₂, suggesting an important role of medium range order in controlling the variations in thermodynamic properties.     

自适应空间信息移动服务

空间信息移动服务系统是空间信息系统继由传统PC计算环境向有线Web分布式计算环境扩展后，向移动计算环境的新发展。文中在分析移动计算环境概念和特点的基础上，讨论了空间信息移动服务的若干特点及关键技术，研究了自适应空间信息移动服务方案。     

基于多传感器观测信息抗差估计的自适应融合导航

首先利用抗差估计原理构造了基于观测信息的融合导航解，再利用动力学模型信息进行自适应融合，最后利用模拟算例进行多种方案的计算与比较。     

基于光谱信息的遥感图像空间域自适应滤波

遥感图像往往由于内外因素的干扰含有各种噪声 ,为提高图像质量人们对其进行滤波。常规的滤波方式完全基于图像空间域 ,在消除异常点使图像平滑的同时使边界变得不清楚从而使图像模糊 ;或者正相反 ,在边缘信息得到增强时也放大了图像噪声而使图像变得粗糙。该文的自适应滤波方法充分利用多光谱和高光谱遥感图像的光谱维信息 ,滤波时不仅要使均匀的地块得到平滑 ,而且要使地块间的边缘、局部的异常点、线仍然得到保存、在光滑的同时尽量保持原有的数值特征     

基于方差分量估计的自适应融合导航

多源传感器观测信息的精度一般不一致,利用方差分量估计理论可以合理地顾及各传感器观测信息在融合导航解中的权比.首先给出基于多源观测信息的融合导航解算模式,进而基于方差分量估计讨论了各传感器观测信息在融合导航解中的合理平衡问题,然后应用自适应因子顾及动力学模型预报信息的贡献,给出了计算过程,并利用模拟数据进行了试算与比较.