2006-2022年黔南州冰雹特征分析

【目的】为了解黔南州的冰雹特征。【方法】利用2006—2022年多普勒天气雷达、常规气象观测资料以及人工影响天气作业站点冰雹观测等资料,采用统计学方法分析了影响黔南州冰雹个例的冰雹直径、降雹持续时间、冰雹日变化、冰雹云移动速度等特征。【结果】黔南州的降雹主要出现在3、4月份,降雹以中冰雹为主,冰雹日变化明显,一天中冰雹主要发生在15时—次日00时,白天17—20时冰雹频发。降雹持续时间短,65%的降雹持续时间在5 min以内。冰雹云单体的移动速度范围为16~102 km·h-1,平均速度50 km·h-1。冰雹云单体的维持时间最短仅为17 min,最长可达290 min,平均122 min。冰雹云移动路径主要以西南路径为主,其次是西北路径和偏西路径。西南路径降雹点主要分布在黔南州中部一线,西北路径降雹点主要分布在黔南州中西部的惠水、长顺,偏西路径的降雹点主要在黔南州中北部。影响黔南的冰雹云源地有境外移入和黔南州境内生成的两类,主要源地在安顺市、黔南州、黔西南州东部和北部、毕节市东部和南部以及贵阳市南部,不同路径的冰雹云源地具有明显的分布差异。【结论】本文研究成果可进一步提高对黔南冰雹特征的认识。     

新型移动三维激光扫描技术在盾构管片椭圆度检测中的应用

铁运营阶段对隧道结构的变形监测保证了地铁运行的安全,而椭圆度检测是地铁隧道结构检测的重要工作。本文简单介绍了传统椭圆度检测的基本方法,分析了新型移动三维激光扫描检测系统基本原理及隧道椭圆度检测的方法和处理流程。通过工程案例实际应用以及对检测结果的综合分析,证明了移动三维激光扫描技术在盾构管片椭圆度检测中的优势。     

Direct numerical simulation of flow over a slotted cylinder at low Reynolds number

Direct numerical simulation was conducted to investigate the flow past a slotted cylinder at low Reynolds number (Re) of 100. The slotting of cylinder affects the boundary layer separation, vortex formation position, recirculation region length and wake width, which are determined by the type of slit. The streamwise slit (SS1), T-shaped slit (SS3) and Y-shaped slit (SS4) act as passive jets, while the transverse slit (SS2) achieves an alternate self-organized boundary layer suction and blowing. The flow rate in slits fluctuates over time due to the alternate vortex shedding and fluctuating pressure distribution around the cylinder surface. One fluctuation cycle of flow rate is caused by a pair of vortices shedding for SS2, SS3 and SS4, while it is created by each vortex shedding for SS1. The wall shear stress and flow impact on the slit wall partly contribute to the hydrodynamic forces acting on the slotted cylinder. Taking into account the internal wall of slit, the transverse slit plays the best role in suppressing the fluid forces with drag reduction of 1.7% and lift reduction of 17%.     

Ekman drift and vortical structures

In this article, the authors study the influence of a constant wind on the displacement of a vortex. The well known Ekman current develops in the surface layer and is responsible for a transport perpendicular to the wind: the Ekman drift.An additional process is, however, evidenced, whose importance is as strong as the Ekman drift. There indeed exists a curl of the wind-driven acceleration along isopycnic surfaces when they are spatially variable (they enter and leave the depth where the wind stress acts), which generates potential vorticity anomalies. This diabatic effect is shown to generate potential vorticity anomalies which acts on the propagation of vortical waves and non linear vortices.It is shown that this effect drastically reduces the effect of the Ekman drift for linear waves and surface intensified vortices, while extending its effect to subsurface vortices. It also generates along wind propagation, whose sign depends on the vortex characteristics.     

Comparison of flow patterns in the near wake of a circular cylinder and a square cylinder placed near a plane wall

The flow patterns in the near wake of a cylinder (either circular or square in shape, D=25 mm) placed in the proximity of a fully developed turbulent boundary layer (thickness δ=0.4D) are investigated experimentally using particle image velocimetry (PIV). The effects of changing the gap height (S) between the cylinder bottom and the wall surface, over the gap ratio range S/D=0.1–1.0, have been investigated. The results show that both the ensemble-averaged and instantaneous flow fields are strongly dependent on S/D. The flow patterns for the two types of cylinders share many similarities with respect to the change in S/D, such as the reduced recirculation length and increased velocity fluctuation in the near wake with increasing S/D, as well as the trend of suppression of vortex shedding at small S/D and onset of vortex shedding at large S/D. However, developments of the shear layers, in terms of wake width, flow curvature, etc., are considerably different for these two types of cylinders. In general, the wake development and momentum exchange for the square cylinder are slower those for the circular cylinder at the same gap ratio. Correspondingly, it is shown that the periodic vortex shedding is delayed and weakened in the case of square cylinder, as compared to that of the circular cylinder at the same S/D.     

夏半年川西高原600 hPa低涡活动特征

600 hPa天气系统能够分析川西高原低涡变化的主要特征,并能识别低涡的发展移动和川西高原强降水落区的关系。利用1979—2020年逐3 h的ERA5再分析资料(0.25°×0.25°)和2011—2020年逐小时降水资料,对夏半年川西高原600 hPa低涡活动特征、低涡与降水的关系及致雨低涡动力和热力特征进行统计分析,结果表明：(1)42年间低涡年均80个,持续时间1 d以内占总数的95.7%;在川西高原本地生成、移入和移出低涡年均61.5个、18个和5.3个;低涡源地和消散地分别在甘孜州白玉县和理塘县为中心的区域。(2)生命史大于12 h的低涡占比36.4%,都会带来降水,其中超83.7%会造成中雨以上降水;低涡伴随的日降水强度最大值中心位置随月份先由川西高原东部与南部地区北移到中部,之后逐渐移回到东部与南部地区,相对应7—8月多低涡从北部南移到中部摆动消亡,其余月份多低涡从中部生成影响到东部和南部地区或在南部生成并停滞或摆动。(3)强烈垂直上升运动和正涡度区的耦合发展以及深厚不稳定层结的形成和加强是致雨低涡发生发展并产生强降水的动力特征和热力层结条件。     

Application of Line Boundary Technique to 2D Tidal Current Simulation

To deal with the problems concerning the shore boundary,moving boundary and engineeringboundary which are encountered frequently in 2D tidal current simulation by the finite difference method,theconcept of line boundary is introduced and studied here,and then the line boundary technique in common useis proposed in this paper.Analysis of some calculation cases shows that this technique is practical,effective,and simple in 2D tidal current simulation involving different boundaries.     

旋转椭球面上的应变与转动张量表达

以旋转椭球体面上某点为原点建立一个大地坐标单位活动坐标架. 通过平移, 使活动坐标架的原点与以椭球中心为原点的笛卡尔单位标架的原点相重合. 然后再通过两次标架旋转, 使活动坐标架与笛卡尔单位标架完全重合. 本文给出了使两个单位标架相重合的转换关系式, 以及该点位移在两个单位标架中的坐标转换式; 在此基础上, 考虑该点的位移及活动坐标架皆为该点大地坐标的函数, 经复杂推导, 分别给出了该点位移向量的微分在大地坐标系中的分量以及该点分别沿坐标曲线的弧微分表达式, 继而导出了该点的位移梯度矩阵; 最后推导出了椭球坐标系的应变张量与转动张量表达式, 并对转动张量的几何含义进行了较详细的解释, 且采用曲面理论对球面与椭球面的应变张量间的内在关系进行了讨论.      

南海风暴潮对风场和外围海水敏感性研究

为探索来自西北太平洋台风风暴潮与南海局地生成台风风暴潮不同,本研究在假设两种台风气象条件相同情况下,研究随台风而来外围海水所形成增水对南海沿岸的影响。以0814"黑格比"强台风风暴潮为基础,使用ROMS(regional ocean modeling system)模式进行数值模拟并通过设计对比试验方法进行研究,研究发现在台风登陆时引起的增水最大,最大增水出现在台风路径右侧,其中在沿岸区域,外围海水形成增水约占总增水10%,且大约3 h后出现增水回震现象。同时,设计对比试验,研究来自西北太平洋台风风暴潮对台风路径、台风强度、台风移动速度和流入角等气象条件敏感性,并获得与前人一致的结果。     

Numerical study of sand scour with a modified Eulerian model based on incipient motion theory

Application of the standard Eulerian model to simulations of sand scour results in unrealistic phenomena. Therefore, the present work develops a modified Eulerian model based on sand incipient motion theory. The modified model is applied for simulating a two-dimensional single vertical jet and a moving planar jet. The simulation results generally demonstrate fairly good agreement with published results of scour profiles and the velocity contours of the water and sand phases. In addition, equations to describe self-similar scour profiles for the moving planar jet cases are given. The results demonstrate that the modified model efficiently and accurately simulates the two-dimensional sand scour produced by jets, particularly for the moving jet cases.