内蒙古兴和县曹四夭超大型斑岩钼铅锌金成矿系统年代学及其地质意义

曹四夭斑岩钼矿床位于内蒙古兴和县,是华北克拉通北缘最大的钼矿床。该矿床中部发育斑岩型钼矿体,外围和上部产出热液脉型铅锌金矿体。文章选取1件与斑岩钼矿化共生的绢云母样品进行了40Ar-39Ar定年,获得40Ar-39Ar坪年龄为(144.4±1.2)Ma,相应的39Ar/36Ar-40Ar/39Ar等时线年龄为(146.4±2.2)Ma(MSWD=0.31),将等时线年龄认作绢云母的Ar封闭年龄,表明曹四夭斑岩钼矿化发生在约146 Ma前。选取14件脉型铅锌矿石中的闪锌矿、黄铁矿和磁黄铁矿样品开展了Rb-Sr定年,获得4件闪锌矿的Rb-Sr等时线年龄为(145.1±3.0)Ma(MSWD=0.63);5件黄铁矿的Rb-Sr等时线年龄为(145.2±1.3)Ma(MSWD=0.53);4件闪锌矿、5件黄铁矿和1件磁黄铁矿的Rb-Sr等时线年龄为(145.3±1.0)Ma(MSWD=0.43)。硫化物Rb-Sr定年结果表明曹四夭矿床脉型铅锌矿化形成于约145 Ma前。本次绢云母40Ar-39Ar和硫化物Rb-Sr定年结果表明,曹四夭矿床斑岩型钼矿化和脉型铅锌金矿化为同期产物,两者均形成于晚侏罗世末期,属于同一个斑岩成矿系统。曹四夭矿床硫化物的w(Rb)和w(Sr)分别为0.1867×10~(-6)~1.305×10~(-6)和0.3175×10~(-6)~6.935×10~(-6),Sr同位素初始比值(87Sr/86Sr)i介于0.709 919~0.711 951之间,平均值0.710 952,结合前人获得的辉钼矿Re含量,认为曹四夭矿床的成矿物质主要来源于地壳。     

Tests on low‐ductility RC frames under high‐ and low‐frequency excitations

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.     

高温炉燃烧-红外吸收法测定重铀酸盐中硫质量分数

建立了高温燃烧红外碳硫仪测定重铀酸盐中硫质量分数的分析方法。样品以五氧化二钒为助熔剂,在高温炉燃烧后,用红外吸收测定重铀酸盐中的硫,样品分析重现性好,精密度高,相对标准偏差为0.26%;样品加标回收率在97.1%~103%之间。     

盛夏副高脊线异常变化对我国气温影响及海气背景分析

利用1951—2006年全国160站盛夏（7—8月）气温资料、北半球500hPa高度场和北太平洋海温场资料,分析了盛夏西太平洋副高脊线位置异常变化对我国气温的影响及其与500hPa大气环流和北太平洋海温的关系,结果发现：盛夏副高脊线异常偏北年主要集中出现在上世纪60年代和90年代,副高脊线异常偏南年则主要集中出现在上世纪80年代;盛夏副高脊线位置与长江流域及其以北至黄河中下游以南的我国中东部广大地区气温存在着很好的正相关关系;盛夏副高脊线位置异常变化与东亚中纬度500hPa上空西风环流强弱变化密切相关,前期3月白令海至阿拉斯加地区500hPa高度场异常变化对盛夏副高脊线位置变动有着较好的指示性,前期北太平洋海温距平分布型,尤其是前期3月北亚热带海区关键区海温、加利福尼亚海区关键区海温和关键区综合海温指数对盛夏副高脊线位置异常变化具有很好的指示意义。     

基于遥感数据的夏玉米高温热害监测评估

玉米作为一种重要的粮食作物,其产量对于国家粮食安全的影响至关重要。该文结合遥感与地面实测气温数据,基于地表温度与气温具有显著的线性相关关系,构建我国夏玉米主产区高温热害评估模型,并对该模型进行精度检验。结果表明：平原区域日平均气温的模拟结果决定系数在0.8以上,达到0.001显著性水平,均方根误差在1.8℃左右的小范围内波动;平原区域精度略高,山区精度略低（均方根误差为2.4℃）。利用该模型对2008—2018年黄淮海夏玉米主产区高温热害进行评估,发现2017年和2018年夏玉米受高温热害影响最严重,高温热害区主要分布在河北省东南部、河南省大部以及山东省西部,该结果与实际情况相符。     

Revisiting the morphological method in two-dimensions to quantify bed-material transport in braided rivers

Research in the 1990s showed that bed-material transport rates could be estimated at the reach scale in both one-dimension and, over small spatial scales (10s of m), in two-dimensions. The limit on the latter was the spatial scale over which it was possible to obtain distributed data on morphological change. Here, we revisit the morphological method given progress in both topographical data acquisition and hydraulic modelling. The bed-material transport needed to conserve mass is calculated in both one and two dimensions for a 1600 m × 300 m Alpine braided river “laboratory”. High-resolution topographical data were acquired by laser scanning to quantify Digital Elevation Models (DEMs), and morphological changes caused by the flushing of the water intake were derived from repeated surveys. Based on DEMs of differences, 1D bed-material transport rates were calculated using the morphological method. Then, a 2D hydraulic model was combined with a topographic correction to route sediment through the network of braided channels and to obtain a spatially variable estimate of transport in both downstream and cross-stream directions. Monte Carlo simulation was applied to the routing model parameters, allowing identification of the most probable parameter values needed to minimize negative transport. The results show that within-section spatial compensation of erosion and deposition using the 1D treatment leads to substantial local errors in transport rate estimates, to a degree related to braiding intensity. Even though the 2D application showed that a large proportion of the total transport was actually concentrated into one main channel during the studied low flow event, the proportion of transport in secondary anabranches is substantial when the river starts braiding. Investigations of the effects of DEM resolution, competent flow duration and survey frequency related to ‘travelling bedload’ and sequential erosion-deposition emphasized the critical importance of careful data collection in the application of the morphological method. © 2019 John Wiley & Sons, Ltd.     

白云鄂博赋矿白云岩与微晶丘和碳酸岩墙的碳氧同位素对比研究

本文通过方解石和白云石的碳和氧同位素分析,对比研究了白云鄂博赋矿白云岩、黑脑包微晶丘、北京西山微晶丘、宽沟北正常沉积灰岩和白云鄂博碳酸岩墙,从而探讨了赋矿白云岩的成因及其与超大型Fe-Nb-REE矿床的成因关系。结果为:①黑脑包腮林忽洞群顶部微晶丘和北京西山寒武系顶部微晶丘碳酸盐的δ~(13)C值都在0±2‰左右,δ~(18)O值为18.3‰～25.1‰,均具有典型海相沉积碳酸盐岩的特点;②白云鄂博东矿采场δ~(13)C值为-7.9‰～-1.1‰,δ~(18)O值为9.1‰～20.9‰;矿区东西两端δ~(13)C值-7.9‰～-0.6‰,δ~(18)O值8.6‰～25.7‰;均介于地幔流体与典型沉积碳酸盐岩之间。部分赋矿白云岩样品中白云石与方解石之间的碳氧同位素分馏△~(13)C和△~(18)O值均小于0‰,表明其受到过次生蚀变作用,低δ~(18)O值白云石样品所对应的负△~(18)O值反映了地幔镁质流体对沉积碳酸盐岩的强烈交代作用;③矿区—富稀土碳酸岩墙的δ~(13)C值为-7.2‰～-4.7‰,δ~(18)O价值为11.9‰～16.4‰,表明其碳酸岩岩浆并非原始地幔来源,而可能与俯冲板块携带的沉积碳酸盐岩与地幔流体在深部的高温混合熔融有关。碳酸岩墙中白云石与方解石之间的碳和氧同位素分馏均小于0‰,说明该碳酸岩墙中的白云石与方解石并非同成因矿物,至少其中之一为     

末次盛冰期百年尺度气候变化的南京石笋记录

据年层计数和TIMSU系测年结果,建立了南京汤山葫芦洞YT石笋年际精度时间标尺(18000～14000aB.P.)。除石笋顶部5mm层段外,高分辨率的δ18O、灰度和年层厚度3种指标在百年尺度上具有相当一致的对应关系,表明这3种指标对气候因素变化响应比较敏感。综合石笋δ18O和本区古植被资料,估计末次盛冰期和波令暖期年均温分别达7℃和15℃。石笋揭示的末次盛冰期气候可进一步划分为4个阶段:1)18150～16900aB.P.,年均温和洞穴湿度逐步下降;2)16900～16100aB.P.,年均温和洞穴湿度相对稳定,可进一步划分为3个暖峰和两个冷谷;3)16100～15600aB.P.,年均温快速下降,按氧同位素平衡方程计算,其冷谷可能接近于0℃,但洞穴湿度比前期下降幅度并不大;4)15600～14750aB.P.,年均温和洞穴湿度比较稳定。这种气候演化的阶段性和突变性与北大西洋地区气候记录可以对比,反映极地与东亚季风气候受共同的驱动机制支配。从石笋4种指标(δ18O、δ13C、灰度和年层厚度)的功率谱图中识别出不同尺度的太阳活动周期成分,其中80aGleissberg周期特别显著,表明末次盛冰期边界条件下太阳活动仍是短尺度气候变化的主要驱动力。     

航电在高山区找矿快速突破中的应用

为了寻找一种快速、高效的地球物理找矿手段,在我国西部高山地区——青海省五龙沟开展了大比例尺航电示范测量,采用高精度测量和随地形缓起伏飞行的方式获得了区内高质量的航电数据,通过数据处理,结合物性资料分析了示范区的电磁场特征,进行了异常筛选及异常解释工作,结合快速钻探查证实现了示范区找矿工作的"当年飞行、当年查证、当年见矿"的找矿工作新模式的快速突破.从完成的航电调查工作与找矿效果来看,在高山地区开展航电测量具有速度快、精度高、费用低和找矿效果显著等特点,具有广泛的应用前景和推广价值.     

1961—2020年中国区域性高温过程的气候特征及变化趋势

利用全国2419个国家气象观测站长序列日最高气温资料,依据目前国家气候中心业务上采用的区域性高温过程客观判别标准和综合评估模型,对1961—2020年我国区域性高温过程的最早开始和最晚结束日期、发生频次以及过程的持续时间、覆盖范围、高温强度和综合强度等的气候特征和长期变化趋势进行了分析.结果显示：（1）我国区域性高温过程平均每年发生4次,在5月上旬至10月上旬均可出现,主要集中在6月下旬至8月下旬,其中7、8月发生最为频繁.区域性高温过程在年内的首次出现日期平均为6月18日,末次结束日期平均为8月31日.平均每次过程覆盖760站、高温强度36.4℃、持续日数13天.（2）近60年来,我国区域性高温过程在年内的首次出现日期明显提前、末次结束日期显著推后,整个高温期大幅变长;区域性高温过程的发生频次呈先减少后增加变化特征,1990s以后维持高位;区域性高温过程的平均高温强度先减弱后增强,1980—2020年增强趋势显著;区域性高温过程的覆盖范围显著增大、持续时间显著变长、综合强度显著增强.（3）近60年,我国历年区域性高温过程的首次开始时间和末次结束时间,高温期长度及高温过程发生频次等均没有发生气候突变;区域性高温过程的平均高温强度在1987年由弱转强,并在2002年进一步突变增强.同时,区域性高温过程的影响范围、持续时间和综合强度分别在1998、2016和2012年前后突变增加和增强.总体而言,近60年来我国区域性高温过程已发生了显著变化,高温灾害趋于严重.