纤维素接枝丙烯酰胺/高岭土高吸水性复合材料研究

在高岭土的存在下，以N，N－亚甲基双丙烯酰胺作交联剂，以硝酸铈铵为引发剂微晶纤维素与丙烯酰胺进行接枝共聚反应，合成接枝纤维素／高岭土高吸水性复合材料。研究了纤维素与单体的配比、高岭土添加量、交联剂用量、引发剂用量及反应温度对吸水率的影响。用红外光谱表征复合材料的结构，用电子显微镜观察复合材料的表面与界面。结果表明，高岭土在接枝聚合物中能较好分散，复合材料吸水率达1166，对生理盐水溶液的吸水率达86。     

A scanning electron microscope study of the effects of dynamic recrystallization on lattice preferred orientation in olivine

Effects of dynamic recrystallization on lattice preferred orientation (LPO) in olivine were investigated through the combination of two SEM-based techniques, electron backscattered diffraction (EBSD) technique for crystallographic orientation measurement and backscattered electron imaging (BEI) for dislocation observation. Samples are experimentally deformed olivine aggregates in simple shear geometry. In the sample deformed at T=1473 K and high stresses (480 MPa), only incipient dynamic recrystallization is observed along grain-boundaries. Orientations of these small recrystallized grains are more random than that of relict grains, suggesting an important role of grain-boundary sliding at this stage of recrystallization. In the sample deformed at T=1573 K and low stress (160 MPa), dynamic recrystallization is nearly complete and the LPO is characterized by two [100] peaks. One peak is located at the orientation subparallel to the shear direction and is dominated by grains with high Schmid factor. The other occurs at high angles to the shear direction and is due to the contribution from grains with low Schmid factor. Grains with high Schmid factor tend to have higher dislocation densities than those with low Schmid factor. Based on these observations, we identify two mechanisms by which dynamic recrystallization affects LPO: (1) enhancement of grain-boundary sliding due to grain-size reduction, leading to the modification of LPO caused by the relaxation of constraint for deformation; (2) grain-boundary migration by which grains with lower dislocation densities grow at the expense of grains with higher dislocation densities. Based on the deformation mechanism maps and stress versus recrystallized grain-size relation, we suggest that the first mechanism always plays an important role whereas the second mechanism has an important effect only under limited conditions.     

The eastern Tonale fault zone: a ‘natural laboratory’ for crystal plastic deformation of quartz over a temperature range from 250 to 700 °C

Near the eastern end of the Tonale fault zone, a segment of the Periadriatic fault system in the Italian Alps, the Adamello intrusion produced a syn-kinematic contact aureole. A temperature gradient from 250 to 700 °C was determined across the Tonale fault zone using critical syn-kinematic mineral assemblages from the metasedimentary host rocks surrounding deformed quartz veins. Deformed quartz veins sampled along this temperature gradient display a transition from cataclasites to mylonites (frictional–viscous transition) at 280±30 °C. Within the mylonites, zones characterized by different dynamic recrystallization mechanisms were defined: Bulging recrystallization (BLG) was dominant between 280 and 400 °C, subgrain rotation recrystallization (SGR) in the 400–500 °C interval, and the transition to dominant grain boundary migration recrystallization (GBM) occurred at 500 °C. The microstructures associated with the three recrystallization mechanisms and the transitions between them can be correlated with experimentally derived dislocation creep regimes. Bulk texture X-ray goniometry and computer-automated analysis of preferred [c]-axis orientations of porphyroclasts and recrystallized grains are used to quantify textural differences that correspond to the observed microstructural changes. Within the BLG- and SGR zones, porphyroclasts show predominantly single [c]-axis maxima. At the transition from the SGR- to the GBM zone, the texture of recrystallized grains indicates a change from [c]-axis girdles, diagnostic of multiple slip systems, to a single maximum in Y. Within the GBM zone, above 630±30 °C, the textures also include submaxima, which are indicative of combined basal a- and prism [c] slip.     

Torsional vibrations of elastic foundation on saturated media

A comprehensive analytical solution is developed to examine the torsional vibration of an elastic foundation on a semi-infinite saturated elastic medium for the first time. First, the governing equations of saturated media are solved by use of Hankel transform techniques. Then, based on the assumption that the contact between the foundation and the half-space is perfectly bonded, this dynamic mixed boundary-value problem can lead to dual integral equations, which are further reduced to the standard Fredholm integral equations of the second kind and solved by numerical procedures. Numerical examples are given at the end of the paper. The numerical results indicate that the response of the elastic foundation strongly depends on the material and geometrical properties of both the saturated soil-foundation system and the load acting on the foundation. In most of the cases, the dynamic behavior of an elastic foundation on saturated media significantly differs from that of a rigid plate bearing on the elastic half-space.     

Seismic evaluation of existing nuclear facility using ambient vibration test to characterize dynamic behavior of the structure and microtremor measurements to characterize the soil: a case study

The methods used for a building seismic hazard evaluation are presented with the associated results. The goals of the study are (1) to check the soil nature and the existence or not of a possible site effect around the installation and (2) to characterize the dynamic behavior of the building using ambient vibration records.

The results of the soil study with the Nakamura method are very difficult to interpret because they are not stable in space and time. The spectral ratios method has been used with regional earthquake records. The results of the application of this method allowed us to conclude that the installation was free of site effect.

The ambient vibration measurements on the building brought the conclusion to determine the first and second modes of the structure. These results have been used to calibrate numerical model. The modal shapes in plan (high roof) and in elevation (main column) have been evaluated. The damping of the building has been computed using ambient vibration records.     

乌鲁木齐区域数字遥测台网各子台背景噪声分析

选取乌鲁木齐区域数字遥测台网中 1 1个子台的背景噪声数字记录 ,计算并分析其背景噪声地动速度均方根值 RMS、有效测量动态范围以及噪声功率谱 ,最后确定出各台址背景噪声相对集中的频段     

Dynamic processes of a simple linear dune—a study in the Taklimakan Sand Sea, China

Samples of dune sands, surveys of the morphology and field measurements of wind velocity and direction of a simple linear dune in Taklimakan Sand Sea show that the airflow and sand flux vary with the change of wind direction on the dune surface. Decrease of the airflow stress on the lee flank does not result in much decrease of the sand flux because of the low threshold shear velocities and the airflow conditions. There are no significant relations between the sand flux on the lee flank and the angle of incidence of the airflow. The low threshold shear velocities and the maintenance of the sand flux at the lee flank are the main mechanisms keeping the linear shape of the dunes. Measurements of the sand flux shows that it reaches a maximum on the crest of the dune. The grain size of the transported sands has some differences compared to that of the dune surface. The sands transported are finer than that on the dune surface, but better sorted under the influence of the medium to low wind activity. The field experiment results exhibit that it is possible for the dunes to be shaped as linear dunes during the processes of accumulation and elongation.     

滑带土动力学性质试验研究

为了研究地震高烈度区老滑坡的复活变形原因,本文对滑坡滑带土的动力学特性进行了系列研究。本次试验采用扰动土样,制样基本物理指标按滑带土的现场测试指标确定,在不固结不排水条件下,运用MTS810Teststar程控液压伺服土动三轴仪对单个样品逐级放大动应力的分级试验方法进行。侧向压力 (围压 )分别采用 100kPa、20 0kPa、300kPa三级,通过施加轴向振动荷载 (力 )模拟地震作用,振动波形为正弦波,频率为 1Hz,振幅随试样性质确定。研究结果表明,滑带土在动荷载作用下的动力学性质与其静荷载作用下的力学性质有着较大的差异,主要表现在滑带土的动应力与动应变关系的非线性、滞后性及变形积累特点,动弹性模量与动强度的显著降低以及动阻尼比的显著增大特性。这揭示了动力作用下的滑坡复活原因之一,同时为滑坡稳定性评价和动力作用下的变形机制模拟分析提供了基础资料,也为分析滑带土动力本构模型提供了基本内容。     

聚丙烯酸/绢云母超吸水性复合材料的合成与性能研究

通过丙烯酸与绢云母超纫粉的接技共聚，制备出吸水率为1100倍的超吸水性复合材料。研究了制备过程中各种影响因素，结果表明，当绢云母超纫粉的用量为10％—20％，丙烯酸单体的浓度为25％，单体的中和度为65％，交联剂用量为0．1％，引发剂用量为1．5％，接技共聚反应温度为70℃时，可获得较好的结果。本文讨论了上述反应因素对复合材料吸水率的影响，并探讨了吸水材料的颗粒大小对吸水性能的影响。     

内蒙古固阳渣尔泰山群层序地层学及其控制因素

渣尔泰山群是华北地台北缘中元古代裂陷槽沉积,主要为一套遭受绿片岩相区域变质的碎屑岩-碳酸盐岩建造。根据岩性、岩相、相序和不整合界面的综合研究,对这套地层进行了详细的层序界面分析和层序划分,识别出Ⅰ型、Ⅱ型和暴露-淹没复合型(Ⅲ型)3种类型层序界面,共划分出1个超层序、2个大层序和7个层序。总结了渣尔泰山群在碎屑滨岸、台缘碳酸盐岩与碎屑岩混积、碳酸盐台地、台前斜坡和陆棚盆地等不同古地理背景下的层序发育模式及其内部构成特征,并探讨了复合海平面变化、构造活动、沉积物供给、古地形等因素对层序形成和演化的控制作用。