Determining Q of near-surface materials from Rayleigh waves

High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (V_S), compressional (P)-wave velocity (V_P), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor Q_P and S-wave quality factor Q_S in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting Q_S from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from Q_P cannot be ignored when Vs/V_P reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert Q_P from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to Q_P than to Q_S. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.     

The l:200,000-scale map of the near-surface mineral resources of the Federal Republic of Germany

For those who deal with aspects of regional planning that are affected by the extraction of near-surface mineral resources, a simple map that shows the distribution of these resources accompanied by explanatory notes is essential; a preliminary 1:1 million-scale map was published in 1982. The Geological Surveys of the Federal States of Germany, in conjunction with the Federal Institute for Geosciences and Natural Resources, are compiling a series of maps that will cover the country at a scale of 1:200,000. When completed by the end of the next decade, this set of maps will consist of 57 sheets, each of which will be accompanied by explanatory notes. By the end of 1995, 17 sheets had been published BGR reports on the status of a Federal mineral-resource mapping program.     

Image processing of 2D resistivity data for imaging faults

A methodology to locate automatically limits or boundaries between different geological bodies in 2D electrical tomography is proposed, using a crest line extraction process in gradient images. This method is applied on several synthetic models and on field data set acquired on three experimental sites during the European project PALEOSIS where trenches were dug. The results presented in this work are valid for electrical tomographies data collected with a Wenner-alpha array and computed with an l₁ norm (blocky inversion) as optimization method. For the synthetic cases, three geometric contexts are modelled: a vertical and a dipping fault juxtaposing two different geological formations and a step-like structure. A superficial layer can cover each geological structure. In these three situations, the method locates the synthetic faults and layer boundaries, and determines fault displacement but with several limitations. The estimated fault positions correlate exactly with the synthetic ones if a conductive (or no superficial) layer overlies the studied structure. When a resistive layer with a thickness of 6 m covers the model, faults are positioned with a maximum error of 1 m. Moreover, when a resistive and/or a thick top layer is present, the resolution significantly decreases for the fault displacement estimation (error up to 150%). The tests with the synthetic models for surveys using the Wenner-alpha array indicate that the proposed methodology is best suited to vertical and horizontal contacts. Application of the methodology to real data sets shows that a lateral resistivity contrast of 1:5–1:10 leads to exact faults location. A fault contact with a resistivity contrast of 1:0.75 and overlaid by a resistive layer with a thickness of 1 m gives an error location ranging from 1 to 3 m. Moreover, no result is obtained for a contact with very low contrasts (1:0.85) overlaid by a resistive soil. The method shows poor results when vertical gradients are greater than horizontal ones. This kind of image processing technique should be systematically used for improving the objectiveness of tomography interpretation when looking for limits between geological objects.     

北京山区与平原冬季近地面风的精细观测特征

利用2009—2018年冬季北京地区200多个自动气象站逐时10 m风速、风向观测数据,分典型区域（山区、山区与平原过渡区、平原区、城区）研究北京地区冬季近地面风的精细特征,并使用有完整记录的2 a（2017和2018年）冬季延庆高山区不同海拔高度10 m风逐时观测数据,多视角分析高山区不同海拔高度近地面风的特征和成因,以深刻认识北京地区复杂地形条件下冬季近地面风的特征和规律。结果表明:（1）北京地区冬季近地面平均风受西部北部地形、城市下垫面粗糙度和冷空气活动共同影响,平均风速沿地形梯度分布,山区高平原低,平原中又以城区风速最小;盛行西北风和北风,在城区东、西两侧盛行风出现扰流,在山区和过渡区一些地方还存在与局地地形环境明显关联的其他盛行风向。（2）4个典型区域冬季近地面风速日变化均表现为白天风速大于夜间,午间风速最大的“峰强谷平”单峰特征,这一特征的稳定性在城区高、山区低。（3）4个区域冬季弱风（< 1 m/s）频率为31%—42%,城区较高、山区较低;强风（> 10.8 m/s）频次则是山区多、城区少,强风风向主要表现为偏西—偏北,与冷空气活动密切关联;城区、平原区和过渡区偏南风频率均为极小,暗示北京“山区—平原”风模态在冬季是“隐式”的、不易被直接观测到。（4）近地面风的水平尺度代表范围在延庆高山区高海拔处明显大于低海拔处,海拔1500 m附近（平均的边界层顶高度）是延庆高山近地面风速日变化特征的“分水岭”,低于该海拔高度时近地面风速日变化表现为前述“峰强谷平”单峰特征,而高于该海拔高度时近地面风速日变化则呈现相反特征,即夜间大白天小、午间最小的“峰平谷深”特征,这是由边界层湍流活动的日变化及伴随的低层自由大气动量向边界层内下传所致。（5）延庆高山近地面风速大体上随观测高度而增大,高海拔站点日平均风速数倍于低海拔站点。白天—前半夜,海拔约2000 m的站点冬季盛行偏西风,风向变化不大,但风速为2—12 m/s;1000 m左右的低海拔站则风速比较稳定（< 6 m/s）,风向从午间至傍晚相对多变。      

A study of the depth of weathering and its relationship to the mechanical properties of near-surface rocks in the Mojave Desert

Weathered granite extends 70 m deep at Hi Vista in the arid central Mojave Desert of southern California. The low strength of this granite is due to the alteration of biotite and chlorite montmorillonite. Deep weathering probably occurs in most granites, although we cannot rule out some anomalous mechanisms at Hi Vista. Geophysical instruments set in these slightly altered rocks are limited by the unstable behavior of the rocks. Thus, tectonic signals from instruments placed in shallow boreholes give vague results. Geophysical measurements of these weathered rocks resemble measurements of granitic rocks near major faults. The rheology of the rocks in which instruments are placed limits the useful sensitivity of the instruments.     

地面核磁共振技术勘查西北干旱浅层地下水效果浅析

地面核磁共振技术勘查地下水是一种新的应用领域,该技术是目前国际上唯一的能直接进行地下水勘查的技术.我所自一九九九年引进法国Numis仪器以来,先后在陕西黄土区、宁南黄土区等地开展寻找不同类型浅层地下水的试验工作,取得了一定的野外成果.本文是在分析总结这些成果的基础上,针对存在的问题如强干扰背景下勘查结果的可靠性,同一测点"8”字型与"正方形”发射线框二者勘查结果比较等方面进行探讨分析.     

Linking moisture and near-surface wind with winter temperature to reveal the Holocene climate evolution in arid Xinjiang region of China

An increasing number of palaeo-climatic records have been reported to identify the Holocene climate history in the arid Xinjiang region of northwest China. However, few studies have fully considered the internal linkages within the regional climate system, which may limit our understanding of the forcing mechanisms of Holocene climate change in this region. Here, we systematically consider three major issues of the moisture/precipitation, temperature and near-surface wind relevant to the Holocene climate history of Xinjiang. First, despite there still has debated for the Holocene moisture evolution in this region, more climatic reconstructions from lake sediments, loess, sand-dunes and peats support a long-term regional wetting trend. Second, temperature records from ice cores, peats and stalagmites demonstrate a long-term winter warming trend during the Holocene in middle- to high-latitudes of Asia. Third, recent studies of aeolian sedimentary sequences reveal that the near-surface winds in winter gradually weakened during the Holocene, whereas the winter mid-latitude Westerlies strengthened in the Tienshan Mountains. Based on this evidence, in the arid Xinjiang region we propose an early to middle Holocene relatively cold and dry interval, with strong near-surface winds; and a warmer, wetter interval with weaker near-surface winds in the middle to late Holocene during winter. Additionally, we develop a conceptual model to explain the pattern of Holocene climate changes in this region. From the early to the late Holocene, the increasing atmospheric CO₂ content and winter insolation, and the shrinking of high-latitude continental ice-sheets, resulted in increasing winter temperatures in middle to high latitudes in the Northern Hemisphere. Subsequently, the increased winter temperature strengthened the winter mid-latitude Westerlies and weakened the Siberian high-pressure system, which caused an increase in winter precipitation and a decrease in near-surface wind strength. This scenario is strongly supported by evidence from geological records, climate simulation results, and modern reanalysis data. Our hypothesis highlights the important contribution of winter temperature in driving the Holocene climatic evolution of the arid Xinjiang region, and it implies that the socio-economic development and water resources security of this region will face serious challenges presented by the increasing winter temperature in the future.     

几种典型近地表有限导体瞬变电磁特征响应研究

近地表有限导体的瞬变电磁响应中包含其形状、结构特征,如何建立这些特征与其响应之间的关系是近地表有限导体探测与识别的核心问题.本文建立了几种典型有限导体响应的三维感应偶极子模型,通过有限导体早期幂函数衰减的幅度与速率、晚期指数衰减的幅度与时间常数共四个模型参数表征有限导体的形状和结构特征,利用最小二乘拟合算法提取这些模型参数,揭示有限导体的形状、结构特征与模型参数之间的内在联系.理论与实验研究结果表明:具有绕球心旋转对称性的球形目标体,其三维感应偶极子响应完全相同,早期响应呈幂函数衰减,晚期呈e指数衰减,信号幅度和时间常数均能很好反映球体半径与材料特性;具有绕轴旋转对称性目标体,其三维感应偶极子响应部分相同,早期幂函数衰减的幅度与速率主要体现目标体的长度特征,晚期e指数衰减的时间常数体现了目标体的外径与壁厚特征;非轴对称性目标体,其三维感应偶极子响应均不相同,各个感应偶极子参数差异较大.本文的研究对提高瞬变电磁系统区分轴对称目标体与金属碎片能力,降低系统探测虚警率具有重要意义.     

基于ENVI-met模式的城市近地表气温模拟与分析-以南京市部分区域为例

城市不同下垫面与建筑物空间形态对近地表气温等微气候要素产生了重要影响。开展城市气温时空变化模拟与影响因素分析,对于城市热环境评价与城市规划具有重要意义。论文基于高空间分辨率Geoeye-1立体影像,在建筑物高度、下垫面覆盖类型信息提取的基础上,选择南京一中、光华东街、玄武湖、头陀岭4个区域,采用ENVI-met微气候模式,以城市基本气象站南京站的实时气象数据作为背景气象场,模拟不同区域近地表气温的时空分布特征,并利用区域自动气象站观测数据进行精度检验。结果表明:在时间变化上,ENVI-met模拟气温与实测值之间吻合程度较高;在空间分布上,南京一中与光华东街区域气温时空分布规律总体相似,但城市空间形态的差异使得局部区域气温变化不同,玄武湖区域气温由陆地中心向外围呈递减趋势,而头陀岭地形复杂多变,白天气温变化剧烈,夜间空间变化较小。     

起伏地表采集数据的三维直接叠前时间偏移方法

提出一种可对起伏地表采集的三维地震资料直接进行偏移成像的叠前时间偏移方法和流程.它用两个等效速度描述近地表和上覆层对地震波传播的影响,可对炮、检点不在同一水平面的三维地震资料直接进行叠前时间偏移处理.该方法不对近地表地震波传播做垂直出、入射假定,因此可适应高速层出露等不存在明显低、降速带情况.描述近地表和上覆层的两个等效速度参数可依据偏移道集的同相轴是否平直来确定,避免了确定近地表速度的困难;而对已知近地表速度的情况,则可进一步修正近地表速度,获得更好的成像效果.用三维起伏地表的理论数据和中国东部某工区实际数据验证了所发展方法和处理流程的有效性和实用性.