基于弹性拉索的超高墩三塔斜拉桥减震效果研究

为探究超高墩三塔斜拉桥在弹性拉索装置下的减震效果,首先利用SAP2000建立了考虑支座非线性和拉索几何非线性的三维有限元模型;其次基于弹性拉索装置,研究了弹性拉索刚度对三塔斜拉桥地震响应的影响;最后基于数值分析结果并结合某三塔斜拉桥实际工程提出3种减震方案。研究表明:在两边塔塔梁结合处设置弹性拉索可显著减小桥梁在地震作用下的内力和位移响应;提出的方案1(两边塔单根弹性索均为50股,单股刚度均为12000kN/m)、方案2(两边塔单根弹性索均为100股,单股刚度均为10000kN/m)和方案3(15#主塔单根弹性拉索100股,单股刚度10000kN/m;17#主塔单根弹性拉索100股,单股刚度为16000kN/m)相较于无弹性索状态,均可有效降低主塔塔底弯矩、塔底剪力、塔顶位移及主梁纵向位移;相较于方案1,方案2和方案3是更优方案。     

湖泊蒸发观测与计算方法研究进展

湖泊蒸发是连接湖泊水分循环与能量平衡的关键纽带之一,认识湖泊蒸发过程对于理解湖-气间相互作用机制十分重要。然而,由于湖泊的形态结构、地理位置和气候背景不同,各湖泊在不同时间尺度上的蒸发特征不同。湖泊蒸发存在复杂的物理驱动过程、时间尺度相关的反馈以及空间异质性。准确地捕捉并量化湖泊蒸发过程,仍是湖沼学、水文学和气象学等学科的重要研究内容。本文首先介绍了湖泊蒸发的主要观测手段,然后概述了湖泊蒸发在日内、季节、年际、年代际四种不同时间尺度的变化特征;梳理了不同时间尺度各要素对湖泊蒸发的影响,以及湖泊蒸发与湖泊面积和深度等形态结构特性及纬度和海拔等地理因素之间的关系;对自涡度相关技术等高精度仪器应用以来的湖泊蒸发研究进展做出了总结。     

Poynting and polarization vectors based wavefield decomposition and their application on elastic reverse time migration in 2D transversely isotropic media

With the progress in computational power and seismic acquisition, elastic reverse time migration is becoming increasingly feasible and helpful in characterizing the physical properties of subsurface structures. To achieve high-resolution seismic imaging using elastic reverse time migration, it is necessary to separate the compressional (P-wave) and shear (S-wave) waves for both isotropic and anisotropic media. In elastic isotropic media, the conventional method for wave-mode separation is to use the divergence and curl operators. However, in anisotropic media, the polarization direction of P waves is not exactly parallel to the direction of wave propagation. Also, the polarization direction of S-waves is not totally perpendicular to the direction of wave propagation. For this reason, the conventional divergence and curl operators show poor performance in anisotropic media. Moreover, conventional methods only perform well in the space domain of regular grids, and they are not suitable for elastic numerical simulation algorithms based on non-regular grids. Besides, these methods distort the original wavefield by taking spatial derivatives. In this case, a new anisotropic wave-mode separation scheme is developed using Poynting vectors. This scheme can be performed in the angle domain by constructing the relationship between group and polarization angles of different wave modes. Also, it is performed pointwise, independent of adjacent space points, suitable for parallel computing. Moreover, there is no need to correct the changes in phase and amplitude caused by the derivative operators. By using this scheme, the anisotropic elastic reverse time migration is more efficiently performed on the unstructured mesh. The effectiveness of our scheme is verified by several numerical examples.     

Investigating hydrogeomorphic floodplain mapping performance with varying DTM resolution and stream order

Hydrogeomorphic models allow parsimonious, fast and effective floodplain extent mapping using topographic data as the main input. Hydrogeomorphic approaches enforce the principle that floodplains are well-distinguished and unique landscape features within river corridors. We investigated the sensitivity of a hydrogeomorphic floodplain delineation algorithm, based on a hydrological power law, relating flow depth to contributing area, digital terrain model (DTM) resolution and river network hierarchy. In addition, we compared the results to other common floodplain mapping methods using standard flood-hazard maps as a reference. Taking the Arno River Basin, Italy, as a case study, our results show a dependency between the optimal power law parameters and DTM resolution, with larger parameter values required to reach optimal consistency with flood-hazard maps as DTM resolution increased. Floodplain mapping performance was also found to depend on stream order. We further tested the model consistency at a larger scale to evaluate its performance with respect to inundation maps in Hungary, Italy, Spain and the UK. Our study suggests that pre-defined power law parameters can be assumed, considering DTM resolution and stream order, supporting the use of the presented hydrogeomorphic model for large-scale floodplain mapping in ungauged basins where reference flood-hazard maps are not available.     

Non-point source pollution estimation in the Pingqiao River Basin,China, using a spatial hydrograph-separation approach

For efficient and targeted management, this study demonstrates a recently developed non-point source (NPS) pollution model for a year-long estimation in the Pingqiao River Basin (22.3 km²) in China. This simple but physically reasonable model estimates NPS export in terms of land use by reflecting spatial hydrological features and source runoff measurements under different land-use types. The NPS export was separately analysed by a distributed hydrological model, a spatial hydrograph-separation technique, and an empirical water quality sub-model. Simulation results suggest that 57 890 kg of total nitrogen (TN) and 1148 kg of total phosphorus (TP) were delivered. The results, validated with observed stream concentrations, show relative errors of 23.3% for TN and 47.4% for TP. Countermeasures for urban areas (5.3% of total area) were prioritized because of the high contribution rate to TN (14.1%) and TP (26.2%) which is caused by the high degree of runoff (8.5%) and pollution source.     

VARIATION OF THE TRAVEL TIME DIFFERENCE BETWEEN TELESEISMIC PS CONVERTED WAVE AND PP TRANSMITTED WAVE IN FOCAL REGION BEFORE AND AFTER WENCHUAN MS8.0 EARTHQUAKE

When P waves from distant earthquakes meet a velocity discontinuity in the earth's crust and upper mantle, they give rise to a series of converted PS waves besides PP refracted waves. It is possible to monitor the variation of the physical properties of the medium in the limited formation space above the transition zone of the seismogenic zone by measuring the time difference between the teleseismic PS converted wave and the first arrival P wave, that is, time-variation Δt_PS=t_PS-t_P. The advantage of this method is that the transition point of the teleseismic source with similar source is relatively stable at the transition interface, and the accuracy of the measured relative time is high, and the change of the medium in a small range of the seismogenic zone above the conversion interface can be monitored. This paper studies the variation of the travel time difference Δt_PS in focal region before and after Wenchuan M_S8.0 earthquake. We select 2001 to 2012 as the research period, use teleseismic waveforms which occurred in the southern region of Sumatra and Hindu Kush area recorded by Sichuan station YZP and JJS. These teleseisms satisfy 5.0 ≤ M ≤ 6.5, and their waveform signal-to-noise ratio is high with clear initial P-wave motion. The epicentral distance of teleseisms is less than 3 degrees. Then we obtain the variation of the travel time difference Δt_PS between teleseismic PS converted wave and PP transmitted wave recorded during the study period in the two stations. The results show that there is a slow increasing trend of Δt_PS before 2006, and an obvious low value process of Δt_PS appeared in the period about 2 years before the Wenchuan earthquake. The maximum decline was about 0.2~0.3s, more than 4~5 times the measurement error. The low value has a certain degree of return about 2~3 months before the earthquake. The change of arrival time difference indicates that the medium is in different states in different periods of seismogenic process. The sharp decrease in Δt_PS from 2006 to January 2008 may be due to the strong disturbance caused by the stress accumulation of the medium. At this stage, the velocity of P wave and S wave increases with the increase of stress, and the increase of S wave velocity will result in the decrease of Δt_PS. The change of Δt_PS is greatly affected by S wave velocity, so Δt_PS appears to decrease rapidly. Regarding the low value that has a certain degree of return about 2~3 months before the Wenchuan earthquake, the possible reason is that the release of stress is much higher than the accumulation of stress in meta-instability stage. At this stage, the velocity of S wave decreases and the decrease of S wave causes Δt_PS to increase. Then, the Wenchuan earthquake of magnitude 8.0 occurred. It is shown that the teleseismic converted wave method in this paper can monitor the variation of medium's wave velocity before large earthquakes, and it has a good prospect in seismic monitoring and worth further experimental study.     

Revisiting the morphological method in two-dimensions to quantify bed-material transport in braided rivers

Research in the 1990s showed that bed-material transport rates could be estimated at the reach scale in both one-dimension and, over small spatial scales (10s of m), in two-dimensions. The limit on the latter was the spatial scale over which it was possible to obtain distributed data on morphological change. Here, we revisit the morphological method given progress in both topographical data acquisition and hydraulic modelling. The bed-material transport needed to conserve mass is calculated in both one and two dimensions for a 1600 m × 300 m Alpine braided river “laboratory”. High-resolution topographical data were acquired by laser scanning to quantify Digital Elevation Models (DEMs), and morphological changes caused by the flushing of the water intake were derived from repeated surveys. Based on DEMs of differences, 1D bed-material transport rates were calculated using the morphological method. Then, a 2D hydraulic model was combined with a topographic correction to route sediment through the network of braided channels and to obtain a spatially variable estimate of transport in both downstream and cross-stream directions. Monte Carlo simulation was applied to the routing model parameters, allowing identification of the most probable parameter values needed to minimize negative transport. The results show that within-section spatial compensation of erosion and deposition using the 1D treatment leads to substantial local errors in transport rate estimates, to a degree related to braiding intensity. Even though the 2D application showed that a large proportion of the total transport was actually concentrated into one main channel during the studied low flow event, the proportion of transport in secondary anabranches is substantial when the river starts braiding. Investigations of the effects of DEM resolution, competent flow duration and survey frequency related to ‘travelling bedload’ and sequential erosion-deposition emphasized the critical importance of careful data collection in the application of the morphological method. © 2019 John Wiley & Sons, Ltd.     

钢筋-沥青隔震层非线性震动特性研究

为了研究钢筋-沥青隔震层的材料与几何非线性震动特性,对钢筋-沥青隔震结构进行了振动台试验,分析了结构在不同加速度幅值输入时的隔震性能。同时,在钢材的应力-应变关系基础上,考虑构件竖向力的二次矩效应,提出了钢筋-沥青隔震层骨架曲线的计算方法,并结合双线型恢复力模型的滞回规则,建立了相应的恢复力模型。利用建立的恢复力模型,编制程序进行了弹塑性时程分析,并与试验结果作对比。结果表明:当钢筋-沥青隔震层的受力钢筋进入弹塑性阶段时,隔震层能够吸收大部分地震能量,显著降低上部结构的地震反应;弹塑性时程分析结果与试验结果吻合较好,由此建立的恢复力模型准确并且适用,可为钢筋-沥青隔震层的工程设计与非线性地震反应分析提供参考。     

2017年9月4日河北临城M_L4.4地震震源深度测定

震源深度是地震定位中的重要参数之一。对于一个地震,sPn与Pn震相到时差是一个常量,与震中距无关,只与震源深度和地壳模型有关。基于该理论,以河北数字台网数据为基础,识别sPn震相和Pn震相,计算2017年9月4日河北临城ML4.4地震震源深度,结果为6.86km。双差定位法是目前确定震源深度比较精确的方法,双差定位得到的震源深度为7.01km。双差定位法所用数据量比较大,计算过程繁杂。利用sPn与Pn到时差计算震源深度的结果与双差定位法结果接近,计算快速、简单,所需数据量小。因此,将该方法应用到实际工作中,可以快速、准确地测定近震震源深度。     

地磁低点时间与经度的相关性分析

地磁低点时间在空间分布上的主要特征是随着经度变化而变化。为了求出这种变化关系的解析式,首先使用国家地磁台网的数据计算甘肃省近三年13个地磁台站的低点时间序列和低点时间的期望,并绘制了低点时间序列的频次分布图和概率密度曲线;然后对低点时间与台站经度的关系做线性回归,并指出这个线性回归方程应无限趋近于“格林尼治时间-经度”关系式。文章第一次提出台站经度与地磁Z分量低点时间的关系式,并提出它的趋近方程。各台站低点时间的期望就是地磁低点时间的正常背景值,它是判定地磁低点时间异常与否的参考标准。本文的工作完善和发展了丁鉴海先生的地磁低点位移法。