Abstract Physical stratigraphy within shoreface‐shelf parasequences contains a detailed, but virtually unstudied, record of shallow‐marine processes over a range of historical and geological timescales. Using high‐quality outcrop data sets, it is possible to reconstruct ancient shoreface‐shelf morphology from clinoform surfaces, and to track the evolving morphology of the ancient shoreface‐shelf. Our results suggest that shoreface‐shelf morphology varied considerably in response to processes that operate over a range of timescales. (1) Individual clinoform surfaces form as a result of enhanced wave scour and/or sediment starvation, which may be driven by minor fluctuations in relative sea level, sediment supply and/or wave climate over short timescales (101?103 years). These external controls cannot be distinguished in vertical facies successions, but may potentially be differentiated by the resulting clinoform geometries. (2) Clinoform geometry and distribution changes systematically within a single parasequence, reflecting the cycle in sea level and/or sediment supply that produced the parasequence (102?105 years). These changes record steepening of the shoreface‐shelf profile during early progradation and maintenance of a relatively uniform profile during late progradation. Modern shorefaces are not representative of this stratigraphic variability. (3) Clinoform geometries vary greatly between different parasequences as a result of variations in parasequence stacking pattern and relict shelf morphology during shoreface progradation (105?108 years). These controls determine the external dimensions of the parasequence. 相似文献
Land subsidence caused by compression of clay layers in Ojiya City, Japan was measured by global positioning system (GPS) between 1 April 1996 and 31 December 1998.
Three baselines were selected in and around the city, and height difference on a WGS-84 ellipsoid was measured by GPS on each baseline. The ground at the GPS station in the city subsides and rebounds 7 cm every winter and spring, respectively. Measurement accuracy was 9.5 mm standard deviation. Ground water level was observed at a well near the GPS station. Regression analysis between total strain, calculated as ratio of the height difference displacement to the total thickness of the clay layers, and the layers' effective stress change with ground water level change gave good correlation. The slope of regression line 7.0×10−11 m2/N was obtained as an average apparent coefficient of volume compressibility of the layers. 相似文献
The design of a drainage system for a roofing slate quarry was implemented by the enhancement of discharge peak estimation, and the uncertainty inevitably associated with the engineering model was reduced.
The development of a topographical, geological, and vegetation cover database developed from a Geographical Information System (GIS) allowed for the definition of the drainage network for a hydraulic system, along with the calculation of the runoff coefficient. This is applied to the digital model of accumulated flow (DMF) as a weight correction coefficient, using a matrix-based model at 5×5 m resolution. The new digital model of corrected accumulated flow (DMCF) is the result of combining the thematic maps with the map of slope <3%, which was previously created from the slope model. It is demonstrated that this new model allows to apply the “Rational Method” on cartographic units defined by the GIS.
The DMCF is compared with other traditional applications of the Rational Method based on the calculation of the discharge peak considering: (1) the drainage basin as a single watershed or (2) defining an average runoff coefficient in each sub-watershed. Both approaches have bigger discharge peaks than those obtained by the DMCF since the slope, lithology, and vegetation cover have average values, and the runoff coefficient is poorly defined, increasing the uncertainty in the discharge peak. 相似文献
Migration characteristics of dense non-aqueous phase liquids (DNAPLs) in the subsurface can be expressed as a water–DNAPL two-phase system based on mainly the k–S–p relations, which describe the relations among relative permeability (k), degree of water saturation (S), and capillary pressure head (p). The aims of this research are to develop an experimental system with new type of probes, such as the electrical conductivity probe for measuring the degree of water saturation and the hydrophilic and hydrophobic tensiometer for measuring the pore water and DNAPL pressures, and also to estimate the results obtained from the developed experimental system. From these tests, the excellent k–S–p relations were obtained and the efficiency and validity of this developed experimental system have been confirmed in terms of the concept of the scaling coefficient calculated by interfacial tensions. 相似文献