The role of bathymetry and directional wave conditions on observed crescentic bar dynamics

Nearshore sandbars are important features in the surf zone of many beaches because they strongly influence the mean circulation and evolving morphology. Due to variations in wave conditions, sandbars can experience cross-shore migration and vary in shape from alongshore uniform (shore-parallel) to alongshore rhythmic (crescentic). Sandbar dynamics have been studied extensively, but existing observational studies usually do not quantify the processes leading to crescentic bar formation and straightening. This study analyses the dynamics of crescentic bar events at the fetch-limited beach of Castelldefels (northwestern Mediterranean Sea, Spain) using 7.5 years of hourly time-exposure video images and detailed wave conditions. The results show that, despite the generally calm wave conditions, the sandbars were very dynamic in the cross-shore and longshore directions. They often migrated rapidly offshore during storms (up to 70 m in one day) and more slowly onshore during post-storm conditions. Crescentic bars were often present at the study site (48% of the time), but only when the sandbar was at least 10 m from the shoreline. They displayed a large variability in wavelengths (100–700 m), alongshore migration speeds (0–50 m/day) and cross-shore amplitudes (5–20 m). Wavelengths increased for larger bar–shoreline distances and the alongshore migration speeds were strongly correlated with the alongshore component of the radiation stresses. Crescentic patterns typically developed during low–medium energetic waves with limited obliquity ( $\theta \lesssim 20$° at 10 m depth), while bar straightening occurred during medium–high energetic waves with strong oblique angles of incidence ( $\theta \gtrsim 15$°). Overall, this study provides further proof for the important role of wave direction in crescentic bar dynamics and highlights the strong dependence of crescentic bar development on the initial bathymetric configuration.     

A combined study of macroseismic data and focal mechanisms applied to the West-Bohemian earthquake,Czechoslovakia

The main shock of the West-Bohemian earthquake swarm, Czechoslovakia, (magnitudem=4.5, depthh=10 km) exhibits an irregular areal distribution of macroseismic intensities 6° to 7° MSK-64. Four lobes of the 6° isoseismal are found and the maximum observed intensity is located at a distance of 8 km from the instrumentally determined epicentre. This distribution can be explained by the energy flux of the directS wave generated by a circular source, the hypocentral location and focal mechanism of which are taken from independent instrumental studies. The theoretical intensity, which is assumed to be logarithmically proportional to the integrated squared ground-motion velocity (i.e.,I=const+log v ² (t)dt), fits the observed intensity with an overall root-mean-square error less than 0.5°. It is important that the present intensity data can also be equally well explained by the isotropic source. The fit was attained by means of a horizontally layered model though large fault zones and an extended sedimentary basin suggest a significant lateral heterogeneity of the epicentral region. The results encourage a broader application of the simple modelling technique used.     

论四川盆地三叠系地下水水文地质条件

四川盆地三叠系地下水可划分出碎屑岩孔隙裂隙和碳酸盐岩岩溶裂隙两大储集类型。按此处构造开启程度和埋深条件等的不同,下中三叠统地下水有沉积变质水和渗入淋滤水两种基本成因类型,水动力特征各异。沉积变质水处于深埋封闭条件,受地静压力驱动控制;渗入淋滤水分布于背斜露头区和浅部地区,受静水压力驱动控制。并由此控制了盆地三叠系盐类的保存条件。     

The petroleum generation potential and effective oil window of humic coals related to coal composition and age

A worldwide data set of more than 500 humic coals from the major coal-forming geological periods has been used to analyse the evolution in the remaining (Hydrogen Index, HI) and total (Quality Index, QI) generation potentials with increasing thermal maturity and the ‘effective oil window’ (‘oil expulsion window’). All samples describe HI and QI bands that are broad at low maturities and that gradually narrow with increasing maturity. The oil generation potential is completely exhausted at a vitrinite reflectance of 2.0–2.2%R_o or T_max of 500–510 °C. The initial large variation in the generation potential is related to the original depositional conditions, particularly the degree of marine influence and the formation of hydrogen-enriched vitrinite, as suggested by increased sulphur and hydrogen contents. During initial thermal maturation the HI increases to a maximum value, HI_max. Similarly, QI increases to a maximum value, QI_max. This increase in HI and QI is related to the formation of an additional generation potential in the coal structure. The decline in QI with further maturation is indicating onset of initial oil expulsion, which precedes efficient expulsion. Liquid petroleum generation from humic coals is thus a complex, three-phase process: (i) onset of petroleum generation, (ii) petroleum build-up in the coal, and (iii) initial oil expulsion followed by efficient oil expulsion (corresponding to the effective oil window). Efficient oil expulsion is indicated by a decline in the Bitumen Index (BI) when plotted against vitrinite reflectance or T_max. This means that in humic coals the vitrinite reflectance or T_max values at which onset of petroleum generation occurs cannot be used to establish the start of the effective oil window. The start of the effective oil window occurs within the vitrinite reflectance range 0.85–1.05%R_o or T_max range 440–455 °C and the oil window extends to 1.5–2.0%R_o or 470–510 °C. For general use, an effective oil window is proposed to occur from 0.85 to 1.7%R_o or from 440 to 490 °C. Specific ranges for HI_max and the effective oil window can be defined for Cenozoic, Jurassic, Permian, and Carboniferous coals. Cenozoic coals reach the highest HI_max values (220–370 mg HC/g TOC), and for the most oil-prone Cenozoic coals the effective oil window may possibly range from 0.65 to 2.0%R_o or 430 to 510 °C. In contrast, the most oil-prone Jurassic, Permian and Carboniferous coals reach the expulsion threshold at a vitrinite reflectance of 0.85–0.9%R_o or T_max of 440–445 °C.     

A laboratory experiment to monitor the contact state of a fault by transmission waves

We performed a series of laboratory experiments in which elastic waves were transmitted across a simulated fault. Two types of experiments were carried out: (1) Normal Stress Holding Test (NSHT): normal stress was kept constant for about 3 h without shear stress and transmission waves were observed. (2) Shear Stress Increasing Test (SSIT): shear stress was gradually increased until a stick-slip event occurred. Transmission waves were continuously observed throughout the process of stress accumulation. We focused on the change in transmission waves during the application of shear stress and especially during precursory slips.It was found in NSHT that the amplitude of transmission waves linearly increased with the logarithm of stationary contact time. The increase amounted to a few percent after about 3 h. Creep at asperity contacts is responsible for this phenomenon. From a theoretical consideration, it was concluded that the real contact area increased with the logarithm of stationary contact time.We observed in SSIT a significant increase in wave amplitude with shear stress application. This phenomenon cannot be attributed to the time effect observed in NSHT. Instead, it can be explained by the mechanism of “junction growth” proposed by Tabor. Junction growth yields an increase in real contact area. It is required for junction growth to occur that the material in contact is already plastic under a purely normal loading condition. A computer simulation confirmed that this requirement was satisfied in our experiments. We also found that the rate at which the amplitude increased was slightly reduced prior to a stick-slip event. The onset time of the reduction well coincides with the onset of precursory slip. The cause of the reduction is attributed to the reset of stationary contact time due to displacement. This interpretation is supported by the result of NSHT. Taking the time of stationary contact in SSIT into account, we may expect the change in wave amplitude to be, at most, only a few percent. The observed slight reduction in increasing rate is, in this sense, reasonable. The static stiffness of the fault also decreases with precursory slip. It was also found that low frequency waves are a better indicator of precursory slip than high frequency waves. This might suggest that low frequency waves with longer wavelength are a better indicator of average behavior of faults. The problem, however, merits a further investigation. The shifts in phase were also found to be a good indicator of the change in contact state of the fault. The changes in both amplitude and phase of transmission waves are unifyingly understood through the theory of transmission coefficient presented by Pyrak-Nolte et al. Rough surfaces have a tendency to give larger stick-slips than smooth surfaces. The amount of precursory slip is larger for rough surfaces than for smooth surfaces. Although it was confirmed by a computer simulation that rough surfaces have larger contact diameters than smooth surfaces, the rigorous relationship between the surface roughness (contact diameter) and the amount of precursory slips was not established.     

Slope instability of San Miniato hill (Florence, Italy): possible deformation patterns

The hill of San Miniato (Florence, Italy) has been repeatedly identified in the past as the site of a slow moving, intermittent landslide. Possible hypotheses regarding the mechanisms responsible for past movements and for cracks and fissures present today are formulated based on the comparison of historical information and processed monitoring data. Although it is not possible to completely exclude a large inactive landslide that involves the entire northern slope, it seems more probable that the slide, if it does exist, is no longer active and that present-day damage is due to separate shallow movements concentrated in man-made deposits. This hypothesis can only be verified with a temporal extension of the monitoring activities, necessary in any case for planning possible safeguarding measures for the cultural heritage in the area.     

Hydrogeology of thermal waters in Viterbo area, central Italy

A conceptual hydrogeological model of the Viterbo thermal area (central Italy) has been developed. Though numerous studies have been conducted on its geological, geochemical and geothermal features, there is no generalized picture defining the origin and yield of the hydrothermal system. These latter aspects have therefore become the objectives of this research, which is based on new hydrogeological and geochemical investigations. The geological setting results in the coexistence of overlapped interacting aquifers. The shallow volcanic aquifer, characterized by fresh waters, is fed from the area around the Cimini Mountains and is limited at its base by the semiconfining marly-calcareous-arenaceous complex and low-permeability clays. To the west of Viterbo, vertical upflows of thermal waters of the sulphate-chloride-alkaline-earth type with higher gas contents, are due to the locally uplifted carbonate reservoir, the reduced thickness of the semiconfining layer and the high local geothermal gradient. The hot waters (30–60°C) are the result of deep circulation within the carbonate rocks (0.5–1.8 km) and have the same recharge area as the volcanic aquifer. The upward flow in the Viterbo thermal area is at least 0.1 m³/s. This flow feeds springs and deep wells, also recharging the volcanic aquifer from below.     

Real Time Analysis and Forecasting of Strata Caving Behaviour during Longwall Operations

Summary. Discontinuous manual observations and irregular caving characteristics of roof rocks often lead to improper decisions resulting in accidents and production loss. Hence, systematic monitoring of the hanging roof behind the chock shields is necessary for safe and productive mining operations. A real-time application was successfully implemented in an Indian mine for forecasting of hanging roof behaviour to enhance safety and productivity. This paper reports the functioning of real-time TWAP (time weighted average pressure) analysis in the forecasting of hanging roof behaviour in real time.     

Temperature dependence of large-scale water-retention curves: a case study

A local-scale model for temperature-dependence of water-retention curves may be applicable to large scales. Consideration of this temperature dependence is important for modeling unsaturated flow and transport in the subsurface in numerous cases. Although significant progress has been made in understanding and modeling this temperature effect, almost all the previous studies have been limited to small scales (on the order of several centimeters). Numerical experiments were used to investigate the possibility of extending a local-scale model for the temperature-dependence of water retention curves to large scales (on the order of meters). Temperature effects on large-scale hydraulic properties are of interest in many practical applications. Numerical experiment results indicate that the local-scale model can indeed be applicable to large-scale problems for special porous media with high air entry values. A typical porous medium of this kind is the porous tuff matrix in the unsaturated zone of Yucca Mountain, Nevada, the proposed geologic disposal site for national high-level nuclear wastes. Whether this finding can approximately hold for general cases needs to be investigated in future studies.     

Control of dust emissions by geomorphic conditions, wind environments and land use in northern China: An examination based on dust storm frequency from 1960 to 2003

The degree to which dust emissions are controlled by geomorphic conditions, wind environments and land use was investigated using the dust storm frequency (DSF) and data from more than 300 meteorological stations throughout northern China. Our analysis showed that most dust emissions originated in gobi deserts that developed in piedmont alluvial fans of the Kunlun, Qilian and Helan mountains. Dust emissions are low from other gobi desert regions, such as the northern Gurbantunggut and eastern Taklimakan, where high vegetation coverage restrained dust emissions or where dust-size particles are not abundant after a long period of strong wind erosion. Sandy deserts with relatively high vegetation coverage or an extensive cover by mobile sands are not a major dust source. Although the highest dust emissions did not appear in regions with the highest wind energy, DSF trends in each region from 1960 to 2003 were closely related to local wind activity. DSF was low in regions with high levels of human activity, where the mean DSF from 1960 to 2003 did not exceed 4 days/year; even from the 1960s to the early 1970s, the period with the greatest DSF, frequency did not exceed 8 days/year, which indicates that extensive land use did not contribute to DSF. The low DSF in these areas might result from the fact that although land use could produce abundant fine soil fractions, vegetation coverage and soil moisture remained higher than in the gobi deserts of arid China, thereby decreasing dust-storm occurrence.