Semi-analytical solutions for vertically and laterally loaded piles in multilayered soil deposits

In geotechnical practice, it is of considerable importance to assess the behavior of vertical–lateral coupled loading piles in multilayered soil deposits. This study deals with a semi-analytical formulation for the performance of a pile suffering from combined vertical and lateral loads. The emphasis is on quantifying the mobilization of the subgrade reaction provided by the layered soil stratums. In the proposed method, subgrade reactions, correlated with both the accumulative axial load transfer and side resistances depending upon the pile–soil interaction, are abstracted as a series of nonlinear springs in both vertical and lateral directions. On account of this, an alternative transfer matrix method is applied to characterize the pile reaction along the depth under the identified boundary conditions atop the pile; meanwhile, the condition of static equilibrium, between two specific pile segments located at the border of soil layers, is also essential. On this basis, validation of the solution is conducted by comparing with observations from experiments and predictions obtained from other existing methods. In addition, the influence of properties in shallow soil layer and the vertical load on the lateral response of the pile is also discussed. The results indicate a reduction in the lateral displacement and the maximum bending moment within the pile with the increase in the shallow soil stiffness, but a growth with the increase in vertical load due to the “P-Δ effect.”     

The influence of the Three Gorges Reservoir regulation on a typical tributary heat budget

Reservoir regulation and local climate both affect the heat budget of tributary bay. It is difficult for traditional methods to identify the influence of different factors on heat budget quantitatively. In this paper, for analysis of the control mechanisms of the heat budget of a large reservoir tributary, the water temperature distribution, and heat budget processes of the Meixi River, a typical tributary to the Three Gorges Reservoir was measured, and a new method was used to calculate the heat content composition of the tributary bay and identify the key factor of the heat balance. The result shows significant variation in the spatial and temporal distributions of water temperatures in the Meixi River, ranging from 12.4 to 28.9 °C on the surface and 12.0 to 24.4 °C at the bottom. The total heat exchange across the air–water interface that ranges from 0.1 to 6% of the budget is not the primary control factor of the annual tributary heat budget. Rather, the change in water depth produced by regulation of the Three Gorges Reservoir is the primary control factor of the tributary heat budget in the whole year, which ranges from 72 to 99% of the budget. The water temperature difference between the main stream and tributary is the not key factor of the heat budget, which ranges from 0.1 to 28% of the heat budget.     

基于GF-2影像西藏桑耶地区岩性-构造遥感解译

西藏桑耶地区位于青藏高原中南部,区内切割强烈,地势陡峻,属于高山峡谷区。为提高区域地质调查野外工作效率,在调查中率先开展了遥感解译研究。在充分收集已有资料的基础上,通过对GF-2卫星数据进行预处理和影像增强,结合野外验证建立了各地质要素的遥感解译标志,实现了区内不同地层岩性、侵入岩、断裂和褶皱等地质要素的提取,最终编制了研究区1:5万遥感地质解译图,为区域地质调查提供了数据支撑。结果表明: 各地质要素在GF-2数据上均有良好反映,完全满足1:5万尺度的遥感地质解译和编图的需要,充分显示出该卫星数据在区域地质调查等工作中具有良好的应用前景。     

Dynamical evolution properties of debris flows controlled by different mesh-sized flexible net barriers

Because the flexible net barrier is a gradually developed open-type debris-flow counter-measure, there are still uncertainties in its design criterion. By using several small-scale experimental flume model tests, the dynamical evolution properties of debris flows controlled by large and small mesh-sized (equal to D₉₀ and D₅₀, respectively) flexible net barriers are studied, including the debris flow behaviors, segregation, and permeability of sediments, as well as the energy absorption rates and potential overtopping occurring when debris flows impact the small mesh-sized one. Experimental results reveal that (a) two sediment deposition patterns are observed depending on variations in debris flow textures and mesh sizes; (b) the aggregation against flexible net barriers is dominated by flow dynamics; (c) the segregation and permeable functions of the barrier are determined by the mesh size, concentration, and flow dynamics; and (d) the smaller mesh-sized flexible net barrier tends to be more efficient in restraining more turbulent debris flows and can absorb greater rate of kinematic energy, and finally, the great kinematic energy dissipation that occurs when secondary debris flows interact with the post-deposits in front of the small mesh-sized flexible net barrier is believed to cause the failure of overtopping phenomenon. The mesh size is concluded to be the decisive parameter that should be associated with debris flow textures to design the control functions of flexible net barriers.     

嫩江科洛地区晚侏罗世深熔花岗岩对嫩江-黑河构造带的响应

通过对嫩江-黑河构造带内的岩石建造研究,在嫩江科洛地区识别出一套深熔花岗岩体,岩石宏观上为一套具非典型花岗岩结构的深熔型侵入岩,具交代结构、斑杂状构造和眼球状构造。对深熔花岗岩进行了锆石LA-ICP-MS U-Pb年龄测试,获得了3组不谐和的U-Pb年龄: 390 Ma、157~163 Ma和113 Ma。其中,113 Ma年龄代表了岩石遭受后期变质热事件年龄; 157~163 Ma的年龄代表了原岩结晶年龄。综合分析深熔花岗岩成因,认为其主要与嫩江-黑河断裂深部韧性剪切热效应作用下发生的深熔有关,深熔花岗岩的划分和厘定为深入研究嫩江-黑河断裂带在中生代的活动提供了新的素材。     

Electrical conductivity of the plagioclase–NaCl–water system and its implication for the high conductivity anomalies in the mid-lower crust of Tibet Plateau

In order to investigate the origin of the high conductivity anomalies geophysically observed in the mid-lower crust of Tibet Plateau, the electrical conductivity of plagioclase–NaCl–water system was measured at 1.2 GPa and 400–900 K. The relationship between electrical conductivity and temperature follows the Arrhenius law. The bulk conductivity increases with the fluid fraction and salinity, but is almost independent of temperature (activation enthalpy less than 0.1 eV). The conductivity of plagioclase–NaCl–water system is much lower than that of albite–NaCl–water system with similar fluid fraction and salinity, indicating a strong effect of the major mineral phase on the bulk conductivity of the brine-bearing system. The high conductivity anomalies of 10^?1 and 10⁰ S/m observed in the mid-lower crust of Tibet Plateau can be explained by the aqueous fluid with a volume fraction of 1 and 9%, respectively, if the fluid salinity is 25%. The anomaly value of 10^?1 S/m can be explained by the aqueous fluid with a volume fraction of 6% if the salinity is 10%. In case of Southern Tibet where the heat flow is high, the model of a thin layer of brine-bearing aqueous fluid with a high salinity overlying a thick layer of partial melt is most likely to prevail.     

An experimental study of Fe–Ni exchange between sulfide melt and olivine at upper mantle conditions: implications for mantle sulfide compositions and phase equilibria

The behavior of nickel in the Earth’s mantle is controlled by sulfide melt–olivine reaction. Prior to this study, experiments were carried out at low pressures with narrow range of Ni/Fe in sulfide melt. As the mantle becomes more reduced with depth, experiments at comparable conditions provide an assessment of the effect of pressure at low-oxygen fugacity conditions. In this study, we constrain the Fe–Ni composition of molten sulfide in the Earth’s upper mantle via sulfide melt–olivine reaction experiments at 2 GPa, 1200 and 1400 °C, with sulfide melt \(X_{{{\text{Ni}}}}^{{{\text{Sulfide}}}}=\frac{{{\text{Ni}}}}{{{\text{Ni}}+{\text{Fe}}}}\) (atomic ratio) ranging from 0 to 0.94. To verify the approach to equilibrium and to explore the effect of \({f_{{{\text{O}}_{\text{2}}}}}\) on Fe–Ni exchange between phases, four different suites of experiments were conducted, varying in their experimental geometry and initial composition. Effects of Ni secondary fluorescence on olivine analyses were corrected using the PENELOPE algorithm (Baró et al., Nucl Instrum Methods Phys Res B 100:31–46, 1995), “zero time” experiments, and measurements before and after dissolution of surrounding sulfides. Oxygen fugacities in the experiments, estimated from the measured O contents of sulfide melts and from the compositions of coexisting olivines, were 3.0?±?1.0 log units more reduced than the fayalite–magnetite-quartz (FMQ) buffer (suite 1, 2 and 3), and FMQ ??1 or more oxidized (suite 4). For the reduced (suites 1–3) experiments, Fe–Ni distribution coefficients \(K_{{\text{D}}}^{{}}=\frac{{(X_{{{\text{Ni}}}}^{{{\text{sulfide}}}}/X_{{{\text{Fe}}}}^{{{\text{sulfide}}}})}}{{(X_{{{\text{Ni}}}}^{{{\text{olivine}}}}/X_{{{\text{Fe}}}}^{{{\text{olivine}}}})}}\) are small, averaging 10.0?±?5.7, with little variation as a function of total Ni content. More oxidized experiments (suite 4) give larger values of K_D (21.1–25.2). Compared to previous determinations at 100 kPa, values of K_D from this study are chiefly lower, in large part owing to the more reduced conditions of the experiments. The observed difference does not seem attributable to differences in temperature and pressure between experimental studies. It may be related in part to the effects of metal/sulfur ratio in sulfide melt. Application of these results to the composition of molten sulfide in peridotite indicates that compositions are intermediate in composition (\(X_{{{\text{Ni}}}}^{{{\text{sulfide}}}}\)?~?0.4–0.6) in the shallow mantle at 50 km, becomes more Ni rich with depth as the O content of the melt diminishes, reaching a maximum (0.6–0.7) at depths near 80–120 km, and then becomes more Fe rich in the deeper mantle where conditions are more reduced, approaching (\(X_{{{\text{Ni}}}}^{{{\text{sulfide}}}}\)?~?0.28)?>?140 km depth. Because Ni-rich sulfide in the shallow upper mantle melts at lower temperature than more Fe-rich compositions, mantle sulfide is likely molten in much of the deep continental lithosphere, including regions of diamond formation.     

Effect of loading duration on uncertainty in creep analysis of clay

Some studies suggest that creep parameters should be determined using a greater quantity of creep test data to provide more reliable prediction regarding the deformation of soft soils. This study aims to investigate the effect of loading duration on model updating. One‐dimensional consolidation data of intact Vanttila clay under different loading durations collected from the literature is used for demonstration. The Bayesian probabilistic method is used to identify all unknown parameters based on the consolidation data during the entire consolidation process, and their uncertainty can be quantified through the obtained posterior probability density functions. Additionally, the optimal models are also determined from among 9 model candidates. The analyses indicate that the optimal models can describe the creep behavior of intact soft soils under different loading durations, and the adopted method can evaluate the effect of loading duration on uncertainty in the creep analysis. The uncertainty of a specific model and its model parameters decreases as more creep data are involved in the updating process, and the updated models that use more creep data can better capture the deformation behavior of an intact sample. The proposed method can provide quantified uncertainty in the process of model updating and assist engineers to decide whether the creep test data are sufficient for the creep analysis.     

大数据环境下内蒙古浩布高地区铅锌多金属矿智能矿产预测研究

传统机器学习算法已广泛应用于矿产预测,但面对地质大数据的高维稀疏、不平衡小样本等特性仍缺乏有效处理和分析的方法,设计适合地质大数据特点的机器学习算法是智能矿产预测亟需解决的新问题。本文以内蒙古浩布高地区的铅锌多金属矿产预测为例,提出了一种面向地质大数据的半监督协同训练矿产预测模型。首先对研究区地质找矿信息和地球化学异常信息进行定量分析,提取断裂构造、二叠系地层、燕山期侵入岩、地层与岩体接触带、围岩蚀变及Pb、Zn、Sn、Cu地球化学异常共9种找矿因子。然后利用递归特征消除法优选找矿因子组合,不包括Sn异常在内的8个找矿因子组合被选为最优组合。最后,利用支持向量机和随机森林算法作为基分类器进行半监督协同训练矿产预测,绘制成矿概率分布图。ROC曲线和预测度曲线分析结果表明,半监督协同训练模型的AUC值和预测效率都高于随机森林和支持向量机模型。研究结果也为大数据环境下的智能矿产预测提供了一种新的思路。     

The Derivation and Validation of TBM Disc Cutter Wear Prediction Model

The problem of disc cutter wear is inevitable when shield or TBM excavating hard rock for a long distance, thus, the study of disc cutter wear model has an important project value on predicting its service life and replacement opportunity. It is put forward by analyzing disc cutter wear mechanism that the main wear form is abrasive wear, which is based on plastic removal mechanism. Then, disc cutter wear rate and linear wear rate prediction models are obtained by approximate calculation and mathematical deduction, which are based on Rabinowicz equation and CSM model. At last, the two models are verified through field test data from three projects, and the results show that the prediction model can accurately reflect the real wear situation of disc cutter.