Identification of Mining Blasts at Mid- to Far-regional Distances Using Low Frequency Seismic Signals

—?This paper reports results from two recent monitoring experiments in Wyoming. Broadband seismic recordings of kiloton class delay-fired cast blasts and instantaneous calibration shots in the Black Thunder coal mine were made at four azimuths at ranges from 1° to 2°. The primary focus of this experiment was to observe and to explain low-frequency signals that can be seen at all azimuths and should routinely propagate above noise to mid-regional distances where most events will be recorded by International Monitoring System (IMS) stations.¶The recordings clearly demonstrate that large millisecond delay-fired cast blasts routinely produce seismic signals that have significant spectral modulations below 10?Hz. These modulations are independent of time, the azimuth from the source and the orientation of the sensor. Low-frequency modulations below 5?Hz are seen beyond 9°. The modulations are not due to resonance as they are not produced by the calibration shots. Linear elastic modeling of the blasts that is guided by mine-blast reports fails to reproduce the fine detail of these modulations but clearly indicates that the enhanced “spectral roughness” is due to long interrow delays and source finiteness. The mismatch between the data and the synthetics is likely due to source processes, such as nonlinear interactions between shots, that are poorly understood and to other effects, such as variations of shot time and yield from planned values, that are known to be omnipresent but cannot be described accurately. A variant of the Automated Time-Frequency Discriminant (Hedlin, 1998b), which uses low-frequency spectral modulations, effectively separates these events from the calibration shots.¶The experiment also provided evidence that kiloton class cast blasts consistently yield energetic 2–10 second surface waves. The surface waves are strongly dependent on azimuth but are seen beyond 9°. Physical modeling of these events indicates that the surface waves are due mainly to the extended source duration and to a lesser extent to the slap-down of spalled material. The directionality is largely a path effect. A discriminant that is based on the partitioning of energy between surface and body waves routinely separates these events from the calibration shots.¶The Powder River Basin has essentially no natural seismic activity. How these mining events compare to earthquake observations remains to be determined.     

Particle recycling in volcanic plumes

We have developed a new theoretical model of an eruption column that accounts for the re-entrainment of particles as they fall out of the laterally spreading umbrella cloud. The model illustrates how the mass flux of particles in the plume may increase with height in the plume, by a factor as large as 2.5 because of this recycling. Three important consequences are that (1) the critical velocity required to generate a buoyant eruption column for a given mass flux increases, (2) the total height of rise of the column may decrease, and (3) we infer that in relatively wind-free environments, for eruption columns near the conditions for collapse, the recycling of particles may lead to an unsteady oscillating motion of the plume, which, in time, may lead to the formation of interleaved fall and flow deposits.     

Modelling Seismic Waves Around Underground Openings in Fractured Rock

—?The potential for large excavation-induced seismic events may be recognised, even if the timing of an event may be inherently unpredictable. In this case, modelling the wave propagation from a potential event could allow the dynamic motions around an excavation to be projected, and for areas of danger to be anticipated. However, the above and other potential applications require accurate models of wave interaction with the openings, as well as with the fractured rock which surrounds such excavations. This paper considers real recorded waveforms and how well these waveforms are modelled by explicit mechanical models of the source, the medium and the excavation. Models of experiments at three different scales of the problem are presented: small and large amplitude waveforms recorded around a deep-level mining tunnel in a synthetic rockburst experiment; waveforms from laboratory experiments of waves through plates of steel representing fractures; waveforms from active pulses in an acoustic emission experiment in a small volume of fractured rock at the surface of an underground excavation. The results show that elastic wave propagation around an excavation was a first approximation for small amplitude waves, but was less successful for modelling large amplitude waves and more fractured rock. Fractures in the models were represented explicitly with displacement discontinuities. Waveforms through known fracture geometries were particularly well-reproduced, and indicate the importance of fracture stiffness, the in situ stress state, and stress-dependence of the fractures in such models. Overall, the models are sufficiently successful at representing recorded behaviour, to be encouraging for the goal of representing accurate wave motions around excavations.     

Efficacy of Annual Bacteria Monitoring and Shock Chlorination in Wells Finished in a Floodplain Aquifer

Public health authorities generally recommend annual water-quality monitoring of rural water wells and shock chlorination if coliforms are detected. It is implicitly assumed that shock chlorination is effective in ridding most wells of bacteriological pathogens for months to years. Neither annual monitoring nor shock chlorination was effective in addressing coliform contamination of selected water wells in a small town developed on an alluvial aquifer where septic system effluents are impacting well water quality. Considerable temporal variation in total and fecal coliforms was observed in water wells monitored for a six-month period. Individual wells intermittently met and exceeded the drinking water criteria, indicating annual sampling was insufficient. Shock chlorination of three contaminated wells and their associated distribution systems proved ineffective because colonies apparently originated from outside the wells and reappeared over relatively short time periods (ranging from less than one week up to 21 weeks). The relatively fast and similar rate of recovery of total heterotrophic bacteria suggested they are related to biofilm formation in the wells and not to ground water contamination.     

"EFFECTS OF FLOW INTENSITY, OBSTACLE ALIGNMENT AND CROSS-SECTION GEOMETRY ON SCOUR AT BRIDGE ABUTMENTS" CARDOSO, A.H., SANTOS, J.S. and ROCA, M.

The authors present new measurements of maximum (equilibrium) local scour depth at bridge abutments, the new data being analysed in terms of the multiplying factors given in Melville (1992,1997) and Melville and Coleman (2000). The design method presented in these publications is referred to here as the University of Auckland (UoA) Method. The authors' data apply to the following factors:∏f (flow intensity), ∏θ (abutment alignment) and ∏g (approach channel geometry).     

Induced Microearthquake Patterns in Hydrocarbon and Geothermal Reservoirs: Six Case Studies

—?The injection or production of fluids can induce microseismic events in hydrocarbon and geothermal reservoirs. By deploying sensors downhole, data sets have been collected that consist of a few hundred to well over 10,000 induced events. We find that most induced events cluster into well-defined geometrical patterns. In many cases, we must apply high-precision, relative location techniques to observe these patterns. At three sedimentary sites, thin horizontal strands of activity are commonly found within the location patterns. We believe this reflects fracture containment between stratigraphic layers of differing mechanical properties or states of stress. At a massive carbonate and two crystalline sites, combinations of linear and planar features indicate networks of intersecting fractures and allow us to infer positions of aseismic fractures through their influence on the location patterns. In addition, the fine-scale seismicity patterns often evolve systematically with time. At sedimentary sites, migration of seismicity toward the injection point has been observed and may result from slip-induced stress along fractures that initially have little resolved shear. In such cases, triggering events may be critical to generate high levels of seismic activity. At one crystalline site, the early occurrence of linear features that traverse planes of activity indicate permeable zones and possible flow paths within fractures. We hope the continued development of microseismic techniques and refinement of conceptual models will further increase our understanding of fluid behavior and lead to improved resource management in fractured reservoirs.     

A New Model for Heat Flow in Extensional Basins: Estimating Radiogenic Heat Production

Radiogenic heat production (RHP) represents a significant fraction of surface heat flow, both on cratons and in sedimentary basins. RHP within continental crust—especially the upper crust—is high. RHP at any depth within the crust can be estimated as a function of crustal age. Mantle RHP, in contrast, is always low, contributing at most 1 to 2 mW/m² to total heat flow. Radiogenic heat from any noncrystalline basement that may be present also contributes to total heat flow. RHP from metamorphic rocks is similar to or slightly lower than that from their precursor sedimentary rocks. When extension of the lithosphere occurs—as for example during rifting—the radiogenic contribution of each layer of the lithosphere and noncrystalline basement diminishes in direct proportion to the degree of extension of that layer. Lithospheric RHP today is somewhat less than in the distant past, as a result of radioactive decay. In modeling, RHP can be varied through time by considering the half lives of uranium, thorium, and potassium, and the proportional contribution of each of those elements to total RHP from basement. RHP from sedimentary rocks ranges from low for most evaporites to high for some shales, especially those rich in organic matter. The contribution to total heat flow of radiogenic heat from sediments depends strongly on total sediment thickness, and thus differs through time as subsidence and basin filling occur. RHP can be high for thick clastic sections. RHP in sediments can be calculated using ordinary or spectral gamma-ray logs, or it can be estimated from the lithology.     

Chemical denudation rates in Kärkevagge, Swedish Lapland

This study examines the spatial and temporal variability of chemical denudation rates in Kärkevagge, northern Sweden. The chemical flux rates within the valley are strongly influenced by the local geology. Chemical denudation rates determined for the study period are more than double those previously reported in the literature for this valley. Rates of greater than 46t km⁻² a⁻¹ were measured at the valley mouth over the course of the melt season. This difference is likely due to differences in measurement technique compared to that used by past researchers. This rate is also much higher than for other arctic and alpine watersheds. Chemical denudation in Kärkevagge is comparable to larger temperate rivers. The rapid chemical denudation in Kärkevagge is likely due to sulfide weathering creating acid solutions.     

Late Archaean to Palaeoproterozoic geotherms in the Kaapvaal craton, South Africa: constraints on the thermal evolution of the Witwatersrand Basin

The c. 2.97–2.71 Ga Witwatersrand Basin located in the Kaapvaal craton of South Africa represents a remnant of a large Late Archaean sedimentary basin that hosts the world's premier gold deposit within a series of conglomerate horizons. Evidence of postdepositional gold mobility within these conglomerates associated with hydrothermal–metamorphic activity has led to speculation about the Late Archaean to Palaeoproterozoic geothermal gradients in the basin. We use surface heat flow and heat production data from rocks in the basin and its environs in order to calculate detailed temperature profiles for the central Kaapvaal craton that show that the steady state crustal geotherm during the Late Archaean and Palaeoproterozoic was relatively cool at 15–20 K km^?1. The geotherm in the upper crustal strata is also largely unaffected by substantial increases in the heat flow into the base of the crust. Consequently, regional greenschist facies metamorphism of the basin sediments could only have been achieved during a transient thermal event that advected heat into the upper crust. The most likely candidate for this is the Bushveld magmatic event at 2.06 Ga.