Salt response of the freshwater microalga Scenedesmus obliquus (Turp.) Kutz is modulated by the algal growth phase

Growth and biochemical responses of the coenobial green alga Scenedesmus obliquus to salinity stress were monitored across different phases of growth. The alga was cultured on BG11 growth medium and subjected to 0, 30, 100, and 200 mmol/L NaCl for a period of 20 d, during which algal cultures were harvested at 4-d intervals. The salinity-induced inhibition of algal growth was accompanied with prolongation of timing of the different growth phases. The sharp and progressive salinity-induced inhibition of algal growth rate during the early phase of growth points to salt shock but moderation of inhibition at the subsequent stages of growth means algal acclimation to salinity. The concentrations of chlorophylls a and b, soluble sugars, proteins as well as those of K+ and Na+ in the alga exhibited peaks at the initiation of the exponential phase of growth, with increasing magnitude in proportion to the increase in the level of salinity. Nevertheless, whereas soluble sugars of the alga peaked at initiation of the exponential phase, starch concentration progressively increased with culture age, reaching saturation towards the stationary phase. Whereas the salinity-induced increase in soluble sugars was most evident at the early stages of growth the reverse was true for starch. The present results point to fast acclimation of S. obliquus to salt stress post a brief salt shock, utilizing soluble sugars, K+ and Na+ for osmotic adjustment. Increasing salinity from 0 to 200 mmol/L NaCl led to progressive increase in soluble sugars, proteins, K + and Na + concentrations of the algal cells, particularly at the early stages of growth. However, the salinity-induced increase in chlorophyll concentration approached a limit at 100 mmol/L NaCl whereas that in starch concentration was more evident at the later stages of growth.     

Geochemical characteristics and spectrometric prospecting in the muscovite-bearing pegmatites and granites,southeastern Aswan,Egypt

Rare metal mineralization of Sn, Nb-Ta and W is encountered in the Gebel Dihmit area （GDA）, southeastern Aswan, Egypt. The mineralization is related to muscovite granites and their pegmatite derivatives. The pegmatites are divided into three types according to their main mineral assemblages： K-feldspar-muscovite-tourmaline, K-feldspar-albite-muscovite and albite-K-feldspar-lepidolite veins. Petrogenetic studies indicate that Sn and Nb-Ta mineralization extends from the late-magmatic stage to the pegmatite and hydrothermal stages of the （GDA） suite. The albite-K-feldspar-lepidolite granite is composed dominantly of albite, lepidolote, and quartz, with topaz, K-feldspar and amblygonite. The accessory minerals are zircon, monazite, pollucite, columbite-tantalite, microlite and Ta-rich cassiterite. Phenocrysts of quartz, topaz and K-feldspar contain abundant inclusions of albite laths and occasional lepidolite crystals along growth zones （snowball texture）, indicating simultaneous crystallization from a subsolvus, residual magma. The origin of the pegmatites is attributed to extreme differentiation by fractional crystallization of a granitic magma. The economic potential for rare metals was evaluated in the geochemical discrimination diagrams. Accordingly, some of the pegmatites are not only highly differentiated in terms of alkalis, but also the promising targets for small-scale Ta and, to a less extent, Sn. The pegmatites also provide the first example of Fe-Mn and Nb-Ta fractionation in successive generations of granites to cassiterite-bearing pegmatites, which perfectly ex- hibit similar fractionation trends established for primary columbite-tantalite in the corresponding categories of pegmatites. Uranium and Th of magmatic origin are indicated by the presence of thorite and allanite, whereas evidence of hydrothermal mineralization is the alteration of rock- foring minerals such as feldspar and the formation of secondary minerals such as uranophane..     

Fusion of RADARSAT-2 and multispectral optical remote sensing data for LULC extraction in a tropical agricultural area

In this study, we investigated the performance of different fusion and classification techniques for land cover mapping in Hilir Perak, Peninsula Malaysia using RADAR and Landsat-8 images in a predominantly agricultural area. The fusion methods used are Brovey Transform, Wavelet Transform, Ehlers and Layer Stacking and their results classified into seven different land cover classes which include (1) pixel-based classifiers (spectral angle mapper (SAM), maximum likelihood (ML), support vector machine (SVM)) and (2) Object-based (rule-based and standard nearest neighbour (NN)) classifiers. The result shows that pixel-based classification achieved maximum accuracy of the optical data classification using SVM in Landsat-8 with 74.96% accuracy compared to SAM and ML. For multisource data classification, the highest overall accuracy recorded for layer stacking (SVM) was 79.78%, Ehlers fusion (SVM) with 45.57%, Brovey fusion (SVM) with 63.70% and Wavelet fusion (SVM) 61.16%. And for object-based classifiers, the overall classification accuracy is 95.35% for rule-based and 76.33% for NN classifier, respectively. Based on the analysis of their performances, object-based and the rule-based classifiers produced the best classification accuracy from the fused images.     

Contribution of Landsat 8 data for the estimation of land surface temperature in Batna city,Eastern Algeria

In this study, we presented a mono-window (MW) algorithm for land surface temperature retrieval from Landsat 8 TIRS. MW needs spectral radiance and emissivity of thermal infrared bands as input for deriving LST. The spectral radiance was estimated using band 10, and the surface emissivity value was derived with the help of NDVI and vegetation proportion parameters for which OLI bands 5 and 4 were used. The results in comparison with MODIS (MOD11A1) products indicated that the proposed algorithm is capable of retrieving accurate LST values, with a correlation coefficient of 0.850. The industrial area, public facilities and military area show higher surface temperature (more than 37 °C) in comparison with adjoining areas, while the green spaces in urban areas (34 °C) and forests (29 °C) were the cooler part of the city. These successful results obtained in the study could be used as an efficient method for the environmental impact assessment.     

Land surface temperature and emissivity estimation for Urban Heat Island assessment using medium- and low-resolution space-borne sensors: A review

The Urban Heat Island (UHI) phenomenon, a typical characteristic on urban landscapes, has been recognised as a key driver to the transformation of local climate. Reliable retrieval of urban and intra-urban thermal characteristics using satellite thermal data depends on accurate removal of the effects of atmospheric attenuations, angular and land surface emissivity. Several techniques have been proposed to retrieve land surface temperature (LST) from coarse resolution sensors. Medium spatial resolution sensors like the Advanced Space-borne Thermal Emission and Reflection Radiometer and the Landsat series offer a viable option for assessing LST within urban landscapes. This paper reviews the theoretical background of LST estimates from the thermal infrared part of the electromagnetic spectrum, LST retrieval algorithms applicable to each of the commonly used medium-resolution sensors and required variables for each algorithm. The paper also highlights LST validation techniques and concludes by stipulating the requirements for LST temporal and spatial configuration.     

Valorization of harbor dredged sediment activated with blast furnace slag in road layers

The valorization solutions for dredged sediment have been the subject of a great number of investigations over the previous decades.In the current present study,treatment of polluted dredged sediment fom the commercial port of Sfax,Tunisia,is proposed.An industrial byproduct(blast furnace slag)was used to bind raw sediment for a reuse in road engineering.Following standards of this field,the raw sediment first was identified and classified according to the French technical guidance.Then an environmental assessment was applied due to the presence of heavy metals.The concentrations were measured on the raw sediment particles so as to control the binding effect on heavy metals.Sediment mixtures consisted of a mix of sand and a blast furnace slag activated with quicklime.Different mixtures were tested and some were proposed for sub-layer applications.The Sfax commercial port raw sediment is considered as a sandy loam with a very low fraction of clay.The measured concentrations of heavy metals exceed the recommended thresholds for cadmium,copper,lead,and zinc.These can induce hazardous effects in the case of their dumping into the sea.On the other hand,the concentrations of the detected elements after leaching tests run on raw sediment samples are very low compared to the thresholds;such results highlight a possible recycling of the raw sediment in subgrade layers without any negative impact.Suitable formulations were deduced for road engineering tests relying on the ratio the California Bearing Ratio index and the immediate bearing index.If the obtained ratio exceeds one,the treated sediment can be recycled and used in road layers.     

The Effect of pH on Electro-osmotic Flow in Argillaceous Rocks

The use of electro-osmosis in geotechnical engineering has been considered since 1930. Its application has been tested in several sectors like the fight against rising damp in porous materials, the consolidation of soils as well as the remediation of the soils contaminated by oil and heavy metals, etc. The paper presents an experimental study of the electrokinetic phenomena resulting from the application of an electric field to argillaceous sandstones. The electroosmotic tests required the development of a completely new experimental device composed of a confining cell, of a system of measurement and control of the pH of the electrolyte near the electrodes, of a system of control and measurement of the voltage and current at the edges of the sample, and of a system of measurement of inlet (anodic) and outlet (cathodic) flows. Various boundary conditions are considered with and without control of pH. In addition, a micro structural modelling of the electrokinetic phenomena makes it possible to quantify the electro osmotic conductivity with a good agreement with experiments.     

Impact of Carpet Waste Fibre Addition on Swelling Properties of Compacted Clays

Municipalities and recycling and environmental authorities are concerned about the growing amount of carpet waste produced by household, commercial and industrial sectors. It is reported that 500,000 tonnes of carpet waste fibre are plunged into landfills annually in the UK. In the United States of America, around 10 million tonnes of textile waste was generated in 2003. In geotechnical engineering, expansive clay soils are categorised as problematic soils due to their swelling behaviour upon increase in the moisture content. The problematic nature of such soils is intensified with the increase in the plasticity index. This paper presents results of a comprehensive investigation into utilisation of carpet waste fibres in order to improve the swelling characteristics of compacted cohesive soils. Therefore, two different clay soils with markedly different plasticity indices (i.e. 17.0 and 31.5 %) were treated with two different types of carpet waste fibre. Waste fibres were added to prepare specimens with fibre content of 1, 3 and 5 % by dry weight of soil. Soil specimens with different dry unit weights and moisture contents were prepared so as to the swelling behaviour of fibre reinforced compacted clays is completely attained under various scenarios. The results indicated that the behaviour of the fibre reinforced soils seems highly dependent on the initial compaction state and secondary on the moisture content. It was found that the swelling pressure drops rapidly as the percentage of fibre increases in samples prepared at the maximum dry unit weight and optimum moisture content. Reducing the dry unit weight, while maintaining constant moisture content or increasing the moisture content at constant dry unit weight was found to reduce the swelling pressure.     

Investigating the Effects of Local Contact Loss on the Earth Pressure Distribution on Rigid Pipes

In this paper, the earth pressure distribution acting on a buried pipe with localized support loss is investigated experimentally and numerically in this study. A laboratory setup has been designed to facilitate the simulation of the local wall separation and to track the changes in earth pressure at selected locations along the pipe circumference. Validated by the experimental results, two-dimensional finite element analysis has been conducted to examine the role of soil-pipe interaction on the pressure distribution around the pipe before and after the contact loss is introduced. Experimental and numerical results revealed that the presence of a gap between the pipe wall and the surrounding backfill can lead to significant changes in contact pressure and bending moment in the pipe wall in the immediate vicinity of the gap. This study suggests that efforts to detect and repair areas experiencing support loss should be made before significant changes in pressure develop causing stress concentration in the pipe wall as it may lead to pipe damage.     

Silicifications pédogénétiques dans les dépôts hamadiens du piémont de Boudenib (Maroc)

Résumé

— Le système de piémont atlasique du Sud marocain, d’âge tertiaire, est constitué dans le secteur de Boudenib de deux unités distinctes. La llamada de Boudenib forme l’unité inférieure et se caractérise par d’importants encroûtements carbonatés, riches en dolomite et attapulgite. L’unité supérieure de la llamada du Cuir marque une reprise de l’érosion et le dépôt de matériaux relativement peu altérés.

Des silicifications affectent les différents faciès de l’unité inférieure, ainsi que les grès crétacés sous-jacents, et jalonnent une surface d’érosion intra-fonnationnelle. Ces silicifications sont précoces, puisque remaniées dans les dépôts ultérieurs. Les illuviations d’opale et les accumulations gramdaires intercalées entre les concrétionnements successifs de silice attestent d’environnements pédologiques. La silicification plus forte vers la partie supérieure des coupes, ainsi que l’association fréquente des faciés silicifiés avec des niveaux hioturhés et altérés sont également à rapporter à des dispositions pédologiques. Ce sont des silcréles pédogénétiques.

L’étude micrographique montre que la silicification procède par épigénie des argiles et des carbonates, ainsi que par des cristallisations dans les vides. C’est à partir des vides existants (fentes, bioturbations et porosité intergranulaire) que se développe la silicification, montrant ainsi le rôle primordial des circulations. En particulier, l’épigénie des carbonates par la silice semble limitée par la diffusion de la silice à partir des vides, où le renouvellement des solutions est assuré. Les séquences de cristallisation des différentes formes de silice (allant de l’opale vers les quartz automorphes) peuvent être interprétées en terme d’évolution du milieu au cours de la silicification. Au fur et à mesure que des dépôts de silice se font sur les parois des vides, les solutions nourricières sont isolées de la roche encaissante, elles se chargent alors moins en cations étrangers, et la cristallisation de plus grands cristaux peut intervenir.

Les silicifications se développent pendant une période de stabilité tectonique et s’installent dans un paysage de glacis et sous des climats chauds à saisons alternées. Leur reconnaissance à l’échelle régionale peut constituer un repère lithostratigraphique précieux.