Three dimensional large scale earthquake simulator with six degrees of freedom

Conclusions When the aseismic test of large scale structure is performed, it is a major performance that the actual response waveform is identical to the input signal waveform under the condition of analog control, especially when the damping of the structure tested is small. The rotational motions of the simulator are induced due to the structure inertia, so that it is a key technique for the simulator design that realizes independent control of the simulator with six degrees of freedom and suppresses the rotational motions. In the design, the modern control techniques are applied and a high performance of the three dimensional earthquake simulator is developed successfully. The simulator can simulate actual earthquake load and it is an important test device for aseismic research. This paper is a main project of the Eighth Five Plan, State Seismological Bureau.     

Characteristics of particle size for creeping and saltating sand grains in aeolian transport

Creep and saltation are the primary modes of surface transport involved in the fluid‐like movement of aeolian sands. Although numerous studies have focused on saltation, few studies have focused on creep, primarily because of the experimental difficulty and the limited amount of theoretical information available on this process. Grain size and its distribution characteristics are key controls on the modes of sand movement and their transport masses. Based on a series of wind tunnel experiments, this paper presents new data regarding the saltation flux, obtained using a flat sampler, and on the creeping mass, obtained using a specifically designed bed trap, associated with four friction velocities (0·41, 0·47, 0·55 and 0·61 m sec^?1). These data yielded information regarding creeping and saltating sand grains and their particle size characteristics at various heights, which led to the following conclusions: (i) the creeping masses increased as a power function (q = ?1·02 + 14·19u_*³) of friction wind velocities, with a correlation (R²) of 0·95; (ii) the flux of aeolian sand flow decreases exponentially with increasing height (q = a exp(–z/b)) and increases as a power function (q = ?26·30 + 428·40 u_*³) of the friction wind velocity; (iii) the particle size of creeping sand grains is ca 1·15 times of the mean diameter of salting sand grains at a height of 0 to 2 cm, which is 1·14 times of the mean diameter of sand grains in a bed; and (iv) the mean diameter of saltating sand grains decreases rapidly with increasing height whereas, while at a given height, the mean diameter of saltating sand grains is positively correlated with the friction wind velocity. Although these results require additional experimental validation, they provide new information for modelling of aeolian sand transport processes.     

聚合物驱组合段塞分注实验研究

萨尔图油田南二区东部140号断层以东地区葡11—4油层,以多段多韵律和正韵律沉积为主,平均孔隙度30．0％,平均空气渗透率1980×10^-3μm2。水驱结束时该油层平均含水92％,采出程度39．5％。计划对该区块实施聚合物驱开采。以往经验认为,组合段塞调整注聚技术能够有效改善流度控制作用。然而对组合注入情况下如何进一步提高驱油效果、注入井分注时机、层段注入强度对开发效果有何影响却很少探讨。通过室内驱油实验,在聚驱的组合段塞注入不同时机（水驱空白阶段、含水下降阶段、含水稳定阶段、含水回升阶段）下调整注入强度实施分注以及在含水回升分注基础上进一步调整注入强度,同时对比不分注实验,评价各方案驱油效果。实验表明：不实施分注时聚驱采收率在水驱基础上提高了19．07个百分点,而组合段塞注入时实施分注均能够在不分注基础上进一步提高驱油效果;空白水驱时实施分注采收率提高幅度最大,为26．55个百分点;随着分注时机的滞后采收率提高幅度增加值依次递减,分注时机越早越好。     

覆盖中国沿海地区的精细化台风风暴潮模型的研究及适用

精细化风暴潮预报是目前风暴潮预报重点发展方向之一,本文首次建立起了一个覆盖整个中国沿海地区的精细化台风风暴潮数值模型,克服了以往分区域数值模型的不足,该模型在中国沿海地区的分辨率达到300m左右。模型采用了并行计算,并对2012年和2013年灾害性台风风暴潮过程进行了数值检验,计算精度和计算所用时间都能够满足业务化运行的要求。本文同时还根据中国气象局、美国国家气象局等5家主要台风预报机构给出的24h台风预报,对2013年度灾害性台风风暴潮过程进行了24h数值预报检验,检验结果表明:根据中国气象局台风登陆前24h预报可以得到更准确的风暴潮预报结果,其预报结果优于其他各家预报结果。该结论可以为今后的台风风暴潮预报中台风路径的选取提供重要的参考。     

Utilization of water resources,ecological balance and land desertification in the Tarim Basin,Xinjiang

Because of the human exploitation and utilization of water resources in the Tarim Basin, the water resources consumption has changed from mainly natural ecosystem to artificial oasis ecosystem, and the environment has changed correspondingly. The basic changes are: desertification and oasis development coexist, both “the human being advance and the desert retreat” and “the desert advance and the human being retreat” coexist, but the latter is dominant. In the upper reaches, water volume drawing to irrigated agricultural areas has increased, artificial oases have been enlarging and moving from the deltas in the lower reaches of many rivers to the piedmont plains. In the middle and lower reaches of the Tarim River, the stream flow has decreased, old oases have declined, natural vegetations have been degenerating, desertification has been enlarging, and the environment has deteriorated. The transition regions, which consist of forestlands, grasslands and waters between the desert and the oases, have been decreasing continuously, their shelter function to the oases has been weakened, and the desert is threatening the oases seriously.     

Late Quaternary palaeosols in the Yangtze Delta, China, and their palaeoenvironmental implications

The stiff clays beneath Holocene strata in the Yangtze Delta are interpreted as palaeosols, based on pedogenic features including illuvial argillans, voids, cracks, iron–manganese concretions and nodules, and carbonate materials. Variations in clay content with depth, the occurrence of foraminifera, and the environmental magnetism characteristics of the palaeosols suggest that their parent materials are floodplain deposits. Anisotropy of magnetic susceptibility (AMS) parameters of the sediments correlate well both with sedimentary dynamics and depositional processes in different sedimentary environments, and AMS analysis may be a useful tool for inferring sedimentary environments. Based on their considerable thickness (> 3.0 m), vertical changes of palaeosol maturity, and occurrence of ageing argillans throughout the palaeosols, the palaeosols are inferred to be compound ones (pedocomplexes) resulting from alternating deposition and pedogenesis on the palaeointerfluve of the Yangtze River. Phytoliths in the palaeosols indicate that climates turned generally from warm and wet to cold and dry with marked fluctuations during development of the palaeosols. This suggests that the palaeosols developed mainly during the marine regression prior to the last glacial maximum. The vertical distribution of manganese materials (e.g., concretions, nodules, speckles and mottles) in the palaeosols suggests that the groundwater tables were about 2.0–3.0 m beneath the upper boundary of the palaeosols during their development. Yellow–brown streaks and speckles are abundant from the middle to lower parts of the palaeosols, and layers with high CaCO₃ content occur in the strata just beneath the palaeosols, but which lack caliche, suggesting that the groundwater table fluctuated markedly during their development. Voids and cracks filled with clays, and carbonate nodules (less than 0.1 mm in diameter) with thin iron–manganese rims are abundant in the palaeosols, indicating that wet and dry seasons were marked during the palaeosol development. It is suggested that the monsoonal influence was marked in the Yangtze Delta, with both winter and summer monsoons strongly developed during the development of the late Quaternary palaeosols.     

Empirical Formula of Shear Strength of Rock Fractures Based on 3D Morphology Parameters

The prime objective of this work is to provide a reference to predict the peak shear strength of rock fractures. The paper studied some shear properties of rock fractures and proposed an empirical formula for the peak shear strength of rock fractures based on 3D morphology parameters. The rock fractures were induced in cylindrical sandstone and marble specimens by means of indirect tension. A rock direct shear apparatus (RDS-200) was adopted to conduct direct shear tests on five groups of rock fractures under different levels of normal load. Before the direct shear test, 3D morphology parameters of rock fracture surfaces were obtained using a 3D optical scanner. By analyses of direct shear test data, the relationships between peak shear strength, peak shear displacement, peak dilatancy angle, residual friction coefficient and peak normal stress were found. According to the evolution trends of peak shear strength and peak dilatancy angle along with the normal stress, an empirical formula was proposed to predict the peak shear strength of rock fractures in both sliding and cutting failure modes considering the 3D morphology parameters of rock fracture surfaces. The empirical formula could be commonly used for different types (sandstone and marble) and grain sizes (powder-grained, fine-grained, medium-grained and coarse-grained) of rock fractures.