Relating millimeter-scale turbulence to meter-scale subtidal erosion and accretion across the fringe of a coastal mangrove forest

Within a wave-exposed mangrove forest, novel field observations are presented, comparing millimeter-scale turbulent water velocity fluctuations with contemporaneous subtidal bed elevation changes. High-resolution velocity and bed level measurements were collected from the unvegetated mudflat, at the mangrove forest fringe, and within the forest interior over multiple tidal cycles (flood–ebb) during a 2-week period. Measurements demonstrated that the spatial variability in vegetation density is a control on sediment transport at sub-meter scales. Scour around single and dense clusters of pneumatophores was predicted by a standard hydraulic engineering equation for wave-induced scour around regular cylinders, when the cylinder diameter in the equations was replaced with the representative diameter of the dense pneumatophore clusters. Waves were dissipated as they propagated into the forest, but dissipation at infragravity periods (> 30 s) was observed to be less than dissipation at shorter periods (< 30 s), consistent with the predictions of a simple model. Cross-wavelet analysis revealed that infragravity-frequency fluctuations in the bed level were occasionally coherent with velocity, possibly indicating scour upstream of dense pneumatophore patches when infragravity waves reinforced tidal currents. Consequently, infragravity waves were a likely driver of sediment transport within the mangrove forest. Near-bed turbulent kinetic energy, estimated from the turbulent dissipation rate, was also correlated with bed level changes. Specifically, within the mangrove forest and over the unvegetated mudflat, high-energy events were associated with erosion or near-zero bed level change, whereas low-energy events were associated with accretion. In contrast, no single relationship between bed level changes and mean current velocity was applicable across both vegetated and unvegetated regions. These observations support the theory that sediment mobilization scales with turbulent energy, rather than mean velocity, a distinction that becomes important when vegetation controls the development of turbulence.     

Observations of asymmetry in contrasting wave‐ and tidally‐dominated environments within a mesotidal basin: implications for estuarine morphological evolution

Tides are often considered to be the dominant hydrodynamic process within mesotidal estuaries although waves can also have a large influence on intertidal erosion rates. Here, we use a combination of hydrodynamic measurements and sediment deposition records to determine the conditions under which observed waves are ‘morphologically significant’, in which case they influence tidal and suspended sediment flux asymmetry and subsequently infilling over geomorphological timescales. Morphological significant conditions were evaluated using data from contrasting arms in a dendritic mesotidal estuary, in which the orientation of the arms relative to the prevailing wind results in a marked difference in wave conditions, deposition rates and morphology. By defining the morphological significance of waves as a product of the magnitude of bed shear stress and frequency of occurrence, even small (but frequently occurring) winds are shown to be capable of generating waves that are morphologically significant given sufficient fetch. In the arm in which fetch length is restricted, only stronger but rare storm events can influence sediment flux and therefore tides are more morphologically significant over longer timescales. Water depth within this mesotidal estuary is shown to be a critical parameter in controlling morphological significance; the rapid attenuation of short period waves with depth results in contrasting patterns of erosion occurring during neaps and accretion during springs. Copyright © 2016 John Wiley & Sons, Ltd.     

<Emphasis Type="Italic">Phragmites australis</Emphasis> (Common Reed) Invasion in the Rhode River Subestuary of the Chesapeake Bay: Disentangling the Effects of Foliar Nutrients,Genetic Diversity,Patch Size,and Seed Viability

The invasion and expansion of the introduced haplotype of Phragmites australis across North America is of growing concern. Previous studies in the Chesapeake Bay region found that Phragmites was more abundant, had higher foliar nitrogen, and produced more viable seeds in brackish wetland subestuaries with more anthropogenic development of the watershed. Here, we focus on a different scale and address issues related to the invasion of Phragmites within a single subestuary, the Rhode River. We evaluated patterns in seed viability, foliar nutrient concentrations, patch size, and genetic variation in ten Phragmites patches in wetlands that occur in the side of the subestuary that is surrounded by forest and 10 patches in wetlands that are in the side of the subestuary that has extensive anthropogenic development. Seed viability varied from 0–60% among the 20 patches but did not differ significantly between patches on the developed vs. forested sides of the Rhode River. Foliar nutrients also did not differ between patches on the two sides of the Rhode River. Seed viability, however, was negatively related to foliar nutrients. Most Phragmites patches consisted of >1 genotype. Larger patches had multiple genotypes, and patches with more genotypes produced more viable seeds. Our study indicates that the Rhode River subestuary behaves as one system with no differences in the measured Phragmites variables between the forested vs. developed sides of the watershed. Our findings also suggest a cyclical process by which Phragmites can spread: larger patches contain more genetic diversity, which increases the chances for cross-fertilization. The subsequent increased production of viable seeds can increase local levels of genetic diversity, which can further facilitate the spread of Phragmites by seed.     

Recent developments of the Middle East catalog

This article summarizes a recent study in the framework of the Global Earth model (GEM) and the Earthquake Model of the Middle East (EMME) project to establish the new catalog of seismicity for the Middle East, using all historical (pre-1900), early and modern instrumental events up to 2006. According to different seismicity, which depends on geophysical, geological, tectonic, and seismicity data, this region is subdivided to nine subregions, consisting of Alborz–Azerbaijan, Afghanistan–Pakistan, Saudi Arabia, Caucasus, Central Iran, Kopeh–Dagh, Makran, Zagros, and Turkey (Eastern Anatolia; after 30° E). After omitting the duplicate events, aftershocks, and foreshocks by using the Gruenthal method, and uniform all magnitude to Mw scale, 28,244 main events remain for the new catalog of Middle East from 1250 B.C. through 2006. The magnitude of completeness (Mc) was determined as 4.9 for five out of nine subregions, where the least values of Mc were found to be 4.2. The threshold of Mc is around 5.5, 5.0, 4.5, and 4.0, for the time after 1950, 1963, 1975, and 2000, respectively. The average of teleseismic depths in all regions is less than 15 km. Totally, majority of depth for Kopeh–Dagh and Central Iran, Zagros, and Alborz–Azerbaijan, approximately, is 15, 13, and 11 km and for Afghanistan–Pakistan, Caucasus, Makran, Turkey (after 30° E), and Saudi Arabia is about 9 km.     

Titanian chondrodite and clinohumite in marbles from the Ötztal crystalline basement

Summary Marble lenses within the polymetamorphic Ötztal crystalline complex frequently contain pockets of clinohumite and chondrodite and their titanium-rich varieties. Chondrodites contain up to 9.1 wt% TiO₂ and clinohumites about half that amount. The maximum amounts of Ti in both minerals do not exeed values of 0.4 in the formula. XTi and X_F are correlated by a slope of –1, indicating the efficiency of the TiO₂Mg_–1F_–2 substitution at constant OH (Evans andTrommsdorff, 1983). Clinohumites sometimes contain lamellae which have nonstoichiometric cation ratios reflecting a composition between clinohumite and olivine. In many cases Ti-rich clinohumites and chondrodites coexist with Mg-ilmenite. Ti-rich clinohumites and chondrodites often break down to a symplectite of Ti-poor clinohumite (or olivine) and Mg-ilmenite. Parts of the marbles, which are barren of Mg-ilmenite contain F-rich clinohumites. The latter do not show any signs of breakdown features. We conclude therefore that fluorine stabilizes the humite group minerals to a wide range of metamorphic conditions. Ti-rich humite-group minerals are not stable till amphibolite facies conditions, and below F-rich humite-group minerals and olivine are the more stable phases in a H₂O-rich, SiO₂-poor carbonate system.

---

Titanreiche Chondrodite und Klinohumite in Marmoren des Ötztalkristallins.

Zusammenfassung In Marmorlinsen des polymetamorphen Ötztalkristaliins kommen häufig titanarme und titanreiche Clinohumite und Chondrodite vor. Die höchsten Titan-Gehalte in Chondrodit betragen 9.1 Gew.-% TiO₂ während Clinohumite nur etwa die Hälfte dieses Wertes enthalten. Dies entspricht einem Maximalgehalt an Titan von 0.4 in den Formeln von Chondrodit und Clinohumit. Eine negative Korrelation zwischen X_Ti, und X_F mit der Steigung von –1 bestätigt die Wirksamkeit der Substitution TiO₂Mg_–1F_–2 bei konstantem OH (Evans undTrommsdorff, 1983). In Clinohumiten konnten nichtstöchiometrische Lamellen nachgewiesen werden, die chemisch zwischen Clinohumit und Olivin zusammengesetzt sind. Ti-reiche Clinohumite und Chondrodite koexistieren immer mit Mg-Ilmenit und wandeln sich häufig an ihren Rändern in einen Symplektit von Ti-ärmerem Clinohumit oder Olivin und Mg-Ilmenit um. In den Mg-Ilmenit freien Bereichen der Marmore kommen stets Ti-arme aber F-reiche Clinohumite vor, die niemals randliche Umwandlungserscheinungen zeigen. Die grobkörnigen (mm-großen) Humitminerale werden der variszischen Metamorphose in Amphibolitfazies zugeschrieben, während die Symplektite als Produkte der eoalpinen grünschieferfaziellen Überprägung angesehen werden. Wir schließen daraus, daß die Humitminerale durch Fluor in einem großen Bereich metamorpher Bedingungen stabilisiert werden, während Ti-reiche Humitminerale bei Bedingungen der Grünschieferfazies instabil werden und F-reiche Humitminerale und Olivin die stabilen Phasen in einem H₂O-reichen, SiO₂-armen Karbonatsystem sind.

     

Influence of tectonic structures on the Hope Slide, British Columbia, Canada

The Hope Slide, which occurred on January 9, 1965, involved an estimated 47-Mm³ of meta-volcanics and intrusive rocks. Previous workers reported the presence of tectonic structures (faults and shear zones) along the failure surface at the Hope Slide. These tectonic features were investigated in detail to assess their effects on rock-mass quality and the related implications for slope stability. This paper integrates basic field and laboratory concepts from structural and engineering geology. Subdividing the failure area into structural domains allowed distinct discontinuity sets to be associated with specific tectonic structures. The Geological Strength Index (GSI) was used to estimate the rock-mass damage related to the tectonic structures. Low GSI values were seen to outline tectonic damage zones. Point-load tests were used to characterise the compressive strength of rocks adjacent to the tectonic structures. Strength anisotropy, tentatively attributed to damage caused by a large shear zone, was observed in greenstone samples. Seepage zones along the failure surface were observed preferentially along shallow discontinuities that dipped downslope and in rock masses of good quality (GSI > 40). An alternative morphology of the slope failure is proposed by distinguishing between the extent of the surficial damage due to the rock-slope failure and the zone of failed material (depletion zone). For the first time, a kinematic mechanism for the Hope Slide is proposed, based on a preliminary 3-dimensional block model. A pre-1965 DEM was produced from estimates of material lost and gained as reported by previous workers. The pre-1965 DEM revealed that the tectonic structures recognised during fieldwork bounded the material that failed in the 1965 event.     

The effect of long-term aerial exposure on intertidal mudflat erodibility

Intertidal zones by definition are exposed to air at low tide, and the exposure duration can be weeks (e.g. during neap tides) depending on water level and bed elevation. Here we investigated the effect of varying exposure duration (6 h to 10 days) on intertidal mudflat erosion (measured using the EROMES device), where the effects of water content and biofilm biomass (using chlorophyll-a content as a proxy, Chl-a μg g⁻¹) were taken into account. Sediments were collected between spring and summer (in October 2018, January 2019 and February 2019) from an intertidal site in the Firth of Thames, New Zealand. Longer exposure duration resulted in more stable sediments [higher erosion threshold (Ƭ_cr, N m⁻²) and lower erosion rate (ER, g m⁻² s⁻¹)]. After 10 days, exposure increased Ƭ_cr by 1.7 to 4.4 times and decreased ER by 11.6 to 21.5 times compared with 6 h of exposure. Chl-a and water content changed with exposure duration and were significantly correlated with changes in Ƭ_cr and ER. The stability of sediments after two re-submersion periods following exposure was also examined and showed that the stabilizing effect of exposure persisted even though water content had increased to non-exposure levels. Re-submersion was associated with an increase in Chl-a content, which likely counteracted the destabilizing influence of increased water content. A site-specific model, which included the interplay between evaporation and biofilm biomass, was developed to predict water content as a function of exposure duration. The modelled water content (W_Mod.) explained 98% of the observed variation in water content (W_Obs.). These results highlight how the exposure period can cause subtle changes to erosion regimes of sediments. An understanding of these effects (e.g. in sediment transport modelling) is critical to predicting the resilience of intertidal zones into the future, when sea-level rise is believed to exacerbate erosion in low-lying areas. © 2020 John Wiley & Sons, Ltd.     

The Plio-Pleistocene glaciation of the Barents Sea–Svalbard region: a new model based on revised chronostratigraphy

Based on a revised chronostratigraphy, and compilation of borehole data from the Barents Sea continental margin, a coherent glaciation model is proposed for the Barents Sea ice sheet over the past 3.5 million years (Ma). Three phases of ice growth are suggested: (1) The initial build-up phase, covering mountainous regions and reaching the coastline/shelf edge in the northern Barents Sea during short-term glacial intensification, is concomitant with the onset of the Northern Hemisphere Glaciation (3.6–2.4 Ma). (2) A transitional growth phase (2.4–1.0 Ma), during which the ice sheet expanded towards the southern Barents Sea and reached the northwestern Kara Sea. This is inferred from step-wise decrease of Siberian river-supplied smectite-rich sediments, likely caused by ice sheet blockade and possibly reduced sea ice formation in the Kara Sea as well as glacigenic wedge growth along the northwestern Barents Sea margin hampering entrainment and transport of sea ice sediments to the Arctic–Atlantic gateway. (3) Finally, large-scale glaciation in the Barents Sea occurred after 1 Ma with repeated advances to the shelf edge. The timing is inferred from ice grounding on the Yermak Plateau at about 0.95 Ma, and higher frequencies of gravity-driven mass movements along the western Barents Sea margin associated with expansive glacial growth.