A GIS Analysis to Evaluate Areas Suitable for Crushed Stone Aggregate Quarries in New England,USA

Aggregate is a low unit-value mineral commodity. Costs to move aggregate from the mine site to the point of use is a large fraction of the resource cost to users. Production sites for aggregate occur where suitable source materials exist and where transportation and market conditions are favorable. The increasing demand for aggregate and the difficulty of developing and permitting new sites and of renewal of permits on existing sites of aggregate production indicates that aggregate will be supplied from sources yet to be developed or delineated in many areas. Site development and permitting for aggregate production is difficult because many land management plans and zoning actions fail to anticipate prospective source areas for aggregate in a way that is consistent with both the source rock quality and the transportation and socioeconomic factors that define the economic viability of the industry. Spatial analysis provides a method to integrate both geology and economic (transportation and marketplace) parameters in a regional model. Weights of evidence (WofE) analysis has been used to measure the spatial correlation of geologic map, transportation network, and population data with current production sites for crushed stone aggregate in the New England region of the northeastern United States. Weighted logistic regression (WLR) is used with the WofE results to rank areas in terms of their relative suitability for production of crushed stone. Spatial analysis indicates that 85% of the 106 crushed stone aggregate quarries in New England are sited within 1.6 km (1 mile) of either a principal highway or rail line in the region. Seventy-eight percent of crushed stone aggregate quarries are sited in census tracts with population densities exceeding 100 people/mile². These relations illustrate the importance of proximity to both transportation corridors and developing areas where aggregate is predominately used. Only one active crushed stone quarry is located in a census tract with a population density less than 15 people/mile², reflecting the lack of sufficient market demand in many rural areas to develop an operation there. However, since 1990, almost all new quarries have been developed in census tracts with population densities less than 200 people/mile², indicating the difficulty of permitting new quarry sites in highly populated areas. Crushed stone aggregate is produced predominately from three hard rock types that are distributed widely in New England; 28% of sites use granitic rock, 25% use carbonate rocks, and 25% use mafic rock types that are categorized as trap rock by the aggregate industry. The other crushed stone aggregate sources include a variety of fine-grained metamorphic rock types. Carbonate rocks and Jurassic basalt (the primary trap rock source) are the most prevalent source rocks on an area-weighted basis. Spatial analysis can be used on a regional scale to rank areas by their relative suitabilityfor crushed stone aggregate production based on geology, transportation, and population parameters. The results of this regional analysis can identify areas for more detailed evaluation. As transportation or population features change, the model can be revised easily to reflect these changes.     

An analytical and experimental study of zoning in plagioclase

A detailed electron microprobe study has been conducted on natural and experimentally grown zoned plagioclase feldspars. Discontinuous, sector, and oscillatory chemical zoning are observed superimposed on continuous normal or reverse zoning trends. The relative accuracy of 3 element (Na, Ca, K) microprobe traverses was found statistically to be 2 mole percent. Comparison of microprobe data on natural zoned plagioclase with zoned plagioclase grown in controlled experiments has shown that it may be possible to distinguish zonal development resulting from physio-chemical changes to the bulk magma from zoning related to local kinetic control on the growth of individual crystals.     

Tourmaline mineralization in the Barberton greenstone belt,South Africa: early Archean metasomatism by evaporite-derived boron

Tourmaline-rich rocks are common in the lowgrade, interior portions of the Barberton greenstone belt of South Africa, where shallow-marine sediments and underlying altered basaltic and komatiitic lavas contain up to 50% tourmaline. The presence of tourmaline-bearing rip-up clasts, intraformational tourmalinite pebbles, and tourmaline-coated grains indicates that boron mineralization was a low-temperature, surficial process. The association of these lithologies with stromatolites, evaporites, and shallow-water sedimentary structures and the virtual absence of tourmaline in correlative deep-water facies rocks in the greenstone bels strengthens this model.Five tourmaline-bearing lithologic groups (basalts, komatiites, evaporite-bearing sediments, stromatolitic sediments, and quartz veins) are distinguished based on field, petrographic, and geochemical criteria. Individual tourmaline crystals within these lithologies show internal chemical and textural variations that reflect continued growth through intervals of change in bulk-rock and fluid composition accompanying one or more metasomatic events. Large single-crystal variations exist in Fe/Mg, Al/Fe, and alkali-site vacancies. A wide range in tourmaline composition exists in rocks altered from similar protoliths, but tourmalines in sediments and lavas have similar compositional variations. Boron-isotope analysis of the tourmalines suggest that the boron enrichment in these rocks has a major marine evaporitic component. Sediments with gypsum pseudomorphs and lavas altered at low temperatures by shallow-level brines have the highest ¹¹B values (+2.2 to-1.9); lower ¹¹B values of late quartz veins (-3.7 to-5.7) reflect intermediate temperature, hydrothermal remobilization of evaporitic boron. The ¹¹B values of tourmaline-rich stromatolitic sediments (-9.8 and-10.5) are consistent with two-stage boron enrichment, in which earlier marine evaporitic boron was hydrothermally remobilized and vented in shallow-marine or subaerial sites, mineralizing algal stromatolites. The stromatolite-forming algae preferentially may have lived near the sites of hydrothermal discharge in Archean times.     

Fluorescence spectral analysis of resinite macerals from coals of the Hanna Formation, Wyoming, U.S.A.

Flourescence spectral analysis indicates that resinite macerals from Tertiary Hanna Formation coals (Hanna Coal Field, southcentral Wyoming, U.S.A.) can be separated into five distinct groups. The first resinite group fluoresces a a medium green (in blue light); its average spectral maximum occurs at or below 440 mm with a red/green quotient of 0.22. The second resinite group fluoresces yellow-green with an average spectral maximum of 500 nm and a red/green quotient of 0.53. The third resinite group displays a yellow fluorescence having an average spectral maximum of 580 nm and a red/green quotient of 0.86. The fourth resinite group fluorescence orange-brown having an average spectral maximum of 610 nm and a red/green quotient of 1.20. These four groups mostly occur as primary globular resinites exhibiting scratches and fractures, indicating that they are brittle, solid substances. Primary cell-filling and secondary fracture-filling resinites also occur in these four groups. The fifth group only occurs as a secondary void-filling material and lacks evidence of br of brittle properties. It fluoresces a reddish-brown, has a spectral maximum at 690 nm, and a red/green quotient of 1.54. The fifth group has properties resembling exsudatinite. The five resinite groups can be separated on the basis of their nine spectral properties alone, without qualitative petrographic interpretation.The relative quantities of the five resinite groups vary among Hanna Formation coals. The origins of these five resinite groups are probably related to their botanical properties and pre- and post-depossitional conditions. Overall, Hanna Formation resinites have petrographic characteristics similar to other North American resinites; however, only four resinite groups have been distinguished in in certain coals from Utah and New Mexico (U.S.A.), and western Canada.     

Analysis of aircraft measurements of momentum flux in the subcloud layer over the tropical atlantic ocean during gate

The momentum flux data obtained by the gust probe aboard the NOAA DC-6 aircraft during GATE are analyzed. Vertical profiles are obtained for Phases I and III and correlated with vertical wind velocity profiles using the geostrophic departure method. Reasonable agreement is obtained using the horizontal equations of motion with negligible advective acceleration. The vertical profiles of momentum flux and wind speed variance compare well with the numerical model results of Deardorff (1972) and Wyngaard et al. (1974). Vertical distributions of power spectra for vertical eddy motion and cospectra corresponding to the momentum flux components are obtained along with the height variation of the dominant length scales of vertical eddy motion and the dissipation rate of turbulence kinetic energy. When normalized by mixed-layer similarity, these results agree well with previous determinations in the boundary layer over tropical oceans and over land.     

Consequences of change and variability in sea ice on marine ecosystem and biogeochemical processes during the 2007–2008 Canadian International Polar Year program

Change and variability in the timing and magnitude of sea ice geophysical and thermodynamic state have consequences on many aspects of the arctic marine system. The changes in both the geophysical and thermodynamic state, and in particular the timing of the development of these states, have consequences throughout the marine system. In this paper we review the ??consequences?? of change in sea ice state on primary productivity, marine mammal habitats, and sea ice as a medium for storage and transport of contaminants and carbon exchange across the ocean-sea-ice-atmosphere interface based upon results from the International Polar Year. Pertinent results include: 1) conditions along ice edges can bring deep nutrient-rich ??pacific?? waters into nutrient-poor surface waters along the arctic coast, affecting local food webs; 2) both sea ice thermodynamic and dynamic processes ultimately affect ringed seal/polar bear habitats by controlling the timing, location and amount of surface deformation required for ringed seal and polar bear preferred habitat 3) the ice edges bordering open waters of flaw leads are areas of high biological production and are observed to be important beluga habitat. 4) exchange of climate-active gases, including CO₂, is extremely active in sea ice environments, and the overall question of whether the Arctic Ocean is (or will be) a source or sink for CO₂ will be dependent on the balance of competing climate-change feedbacks.     

Surface inhomogeneity effects on convective diffusion

It is suggested that convective scaling, with appropriate extensions, provides the most useful framework for estimating the effects of urban-scale surface inhomogeneities on diffusion in convective conditions. Strong contrasts in surface heat flux exist between cropland, forests, urban areas, and water or marshland surfaces. It is argued that a typical fetch for convective turbulence to readjust to changed heat (or buoyancy) input from the surface below is 2(U/w ^*)h, where U is the mean wind speed in the mixing layer, w ^* is the convective scaling velocity, and h is the mixing depth. In contrast, the fetch required for wind speed to readjust to new underlying surface roughness is of the order (U/u ^*)²h/2, where u ^* is the friction velocity.The ratio w ^*/U is the best index of diffusion rates in moderately to very unstable conditions. General urban effects on heat flux, h, and U are discussed separately, then their combined effects on w ^*/U are estimated. While this ratio can double over a large city during light winds, its increase is much less for small cities, or during moderate winds. Finally, some examples of heat flux in- homogeneities causing stationary convective features are presented. Steady downdrafts associated with these features are of the order of 0.4w ^*, and could significantly increase surface concentrations from elevated sources.On assignment from the National Oceanic and Atmospheric Administration, U.S. Department of Commerce.This paper is based on a presentation made at the AMS Specialty Conference on Air Quality Modeling of the Urban Boundary Layer, in Baltimore, late 1983.     

Evaluating soil moisture estimation from ground-penetrating radar hyperbola fitting with respect to a systematic time-domain reflectometry data collection in a boreal podzolic agricultural field

The upper 30 cm of the soil profile, which hosts the majority of the root biomass, can be considered as the shallow agricultural root zone of most temperate crops. The electromagnetic wave velocity in the soil obtained from reflection hyperbolas in ground-penetrating radar (GPR) data can be used to estimate soil moisture (SM). Finding shallow hyperbolas in a radargram and minimizing the subjective error associated with the hyperbola fitting are the main challenges in this approach. Nevertheless, we were motivated by the recent improvements of hyperbola fitting algorithms, which can reduce the subjective error and processing time. To overcome the difficulty of finding very shallow hyperbolas, we applied the hyperbola fitting method to reflections ranging from 27- to 50-cm depth using a 500-MHz centre-frequency GPR and compared the estimated moisture with vertically installed, 30-cm-long time-domain reflectometry (TDR) sensors. We also compared TDR and GPR sample areas in a 2-D plane using different GPR survey types and different hyperbola depths. SM measured with TDR and GPR were not significantly different according to Mann–Whitney's test. Our analyses showed that a root mean square error of 0.03 m³ m⁻³ was found between the two methods. In conclusion, the proposed method might be suitable to estimate SM with an acceptable accuracy within the root zone if the soil profile is fairly uniform within the application depth range.     

Implications of measurement metrics on soil freezing curves: A simulation of freeze–thaw hysteresis

Soil freeze–thaw events have important implications for water resources, flood risk, land productivity, and climate change. A property of these phenomena is the relationship between unfrozen water content and sub-freezing temperature, known as the soil freezing characteristic curve (SFC). It is documented that this relationship exhibits hysteretic behaviour when frozen soil thaws, leading to the definition of the soil thawing characteristic curve (STC). Although explanations have been given for SFC/STC hysteresis, the effect that ‘scale’ – particularly ‘measurement scale’ – may have on these curves has received little attention. The most commonly used measurement scale metric is the ‘support’, which is the spatial (or temporal) unit within which the measured variable is integrated or soil volume sampled. We show (a) measurement support can influence the range and shape of the SFC and (b) hysteresis can be attributed, in part, to the support and location of the measurements comprising the SFC/STC. We simulated lab measured temperature, volumetric water content (VWC), and permittivity from soil samples undergoing freeze–thaw transitions using Hydrus-1D and a modified Dobson permittivity model. To assess the effect of measurement support and location on SFC/STC, we masked the simulated temperature and VWC/permittivity extent to match the instrument's support and location. By creating a detailed simulation of the intra- and inter-support variability associated with the penetration of a freezing front, we demonstrate how measurement support and location can influence the temperature range over which water freezing events are captured. We show it is possible to simulate hysteresis in homogenous media with purely geometric considerations, suggesting that SFC/STC hysteresis may be more of an apparent phenomenon than mechanistically real. Lastly, we develop an understanding of how the location and support of soil temperature and VWC/permittivity measurements influence the temperature range over which water freezing events are captured.     

The synoptic‐ and planetary‐scale signatures of precipitating systems over the Mackenzie River Basin

Abstract

The synoptic‐ and planetary‐scale signatures of precipitating systems over the Mackenzie River Basin (MRB) are elucidated using composites based on a 28‐year sample of widespread precipitation events. These wet events are defined as days on which 5 or more of 12 surface stations in the MRB receive at least 2.5 mm of precipitation. Seasonal composites based on a total of 600 wet events reveal a sequence of statistically significant flow anomalies. Examination of individual wet events motivates stratification of the seasonal samples according to sea‐level pressure distribution. One evolution that is particularly common during fall, winter and spring involves lee cyclogenesis over the southern MRB in association with a strong cyclone over the Gulf of Alaska; such events are dubbed Gulf Redevelopment (GR) cases. A composite based on 59 wintertime GR events indicates upslope flow north of the lee cyclone and warm advection along an east‐west oriented warm front during the precipitation event. Composites of the Q‐vector and the divergence of this field confirm the presence of quasigeostrophic (QG) forcing for ascent over the MRB during this period. A thermally indirect “topographic tilting” mechanism, involving downs‐lope warming over the southern MRB and upslope cooling to the north, is hypothesized to increase warm‐frontal baroclinicity over the MRB. The GR composite 500 hPa geopotential height anomaly pattern is characterized by a series of anomalies extending from the Bering Sea to the Gulf of Mexico. The western (eastern) anomalies tend to decay (amplify) with time. The composite exhibits a positive anomaly over the Bering Sea, a negative anomaly over the Gulf of Alaska that moves eastward into the MRB during the precipitation event, and a positive anomaly that moves eastward over western and central North America. The presence of large, slow‐moving flow anomalies and an extended period of enhanced southwesterly geostrophic flow over the MRB in the composite suggests that a persistent influx of Pacific moisture is required to moisten the atmosphere over the MRB sufficiently for widespread precipitation. An independent composite of dry MRB cyclone events exhibits substantially weaker southwesterly geostrophic flow into the MRB relative to the wet GR composite.