Byproduct Formation During the Reduction of TCE by Zero-Valence Iron and Palladized Iron

Trichloroethene (TCE) was reduced with zero-valence iron and palladized iron in zero-head-space extractors. Progress of the reaction in these batch studies was monitored with purge-and-trap gas chromatography and a flame ionization detector. When a 5 ppm initial concentration of TCF. reacts with zero-valence iron, approximately 140 ppb of vinyl chloride persists for as long as 73 days. The concentration of vinyl chloride (approximately If) ppb) remaining with palladized iron is approximately an order of magnitude less than when zero-valence iron is the reductant. These data suggest that volatile byproducts may be under-represented in oilier published data regarding reduction with zero-valence metals. These results also demonstrate that the reduction of TCE with palladized iron (0.05 percent palladium) is more than an order of magnitude faster than with zero-valence iron. Wilh a 5:1 solution-to-solid ratio the TCE half-life with zero-valence iron is 7.41 hours. but is only 0.59 hours with the palladized iron.     

Morphological and microtectonic analysis of Quaternary deformation from Puná and Santa Clara Islands, Gulf of Guayaquil, Ecuador (South America)

This paper presents the neotectonic study of Santa Clara and Puná Islands sited in the Gulf of Guayaquil eastern part. Both islands are located on the south-western segment of the fault zone bounding to the east the North Andean Block. Fault motion and morphostructural analysis were carried out from Pleistocene age terrain. A two step deformation characterises the South Puná tectonics. The first step involves the Zambapala Cordillera uplift that post-dates Pleistocene sediments and pre-dates a marine terrace correlated with the M.I.S. 11 or 13 (440–550 ka). The second step is the formation of a pull-apart that shows evidence of 2.9 km dextral offset since the M.I.S. 11 or 13, giving an offset mean rate of 5.3 to 6.6 mm/yr. This rate is higher than the one calculated on the Pallatanga Fault northeast of the study area, in the Western Andean Cordillera, suggesting that deformation is split in different fault segments from the Gulf of Guayaquil to the continent. The Zambapala Cordillera uplift and transpression deformation requires a compressive event that may have been induced by the subduction process during the early Pleistocene.     

Emplacement age and thermal footprint of the diamondiferous Ellendale E9 lamproite pipe, Western Australia

The diamondiferous Ellendale 9 (E9) pipe is a funnel-shaped maar-diatreme volcano consisting of inward-dipping tuff sequences intruded by lamproite plugs and dykes. The host rocks for the E9 pipe are Permian sandstones. The multiple lithological contacts exposed within the mined maar volcano provide a natural laboratory in which to study the effect of volcanic processes on U–Th–Pb–He systematics. Zircon from the regional sandstone and E9 lamproite display a bimodal distribution of ages on (U–Th)/He–U/Pb plots. The zircon U/Pb ages for the E9 pipe (n?=?52) range from 440 to 2,725 Ma, while the cluster of (U–Th)/He ages for the lamproite dyke zircon indicate that dyke emplacement occurred at 20.6?±?2.8 Ma, concordant with a maximum emplacement age of about ≤22 Ma from phlogopite ⁴⁰Ar/³⁹Ar. These ages indicate a xenocrystic origin for the zircon entrained in the E9 dyke. The U/Pb ages of detrital zircon from the regional sandstone host (373–3,248 Ma; n?=?41) are indistinguishable from those of the lamproite zircon xenocrysts, whereas the detrital zircon in the host sandstone yield (U–Th)/He ages from 260 to 1,500 Ma. A thermochronology traverse across the E9 lamproite dyke reveals that the zircon (U–Th)/He ages in the host sandstone have not been significantly thermally reset during dyke emplacement, even at the contact. The capability of the zircon (U–Th)/He method to distinguish deep, mantle source lithologies from upper crustal source lithologies could be used in geochemical exploration for diamonds. Pre-screening of detrital samples using etching and helium assay methods will improve the efficiency and decrease the cost of greenfields exploration.     

Some Insights into Topographic,Elastic and Self-gravitation Interaction in Modelling Ground Deformation and Gravity Changes in Active Volcanic Areas

Surface displacements and gravity changes due to volcanic sources are influenced by medium properties. We investigate topographic, elastic and self-gravitation interaction in order to outline the major factors that are significant in data modelling. While elastic-gravitational models can provide a suitable approximation to problems of volcanic loading in areas where topographic relief is negligible, for prominent volcanoes the rough topography could affect deformation and gravity changes to a greater extent than self-gravitation. This fact requires the selection, depending on local relief, of a suitable model for use in the interpretation of surface precursors of volcanic activity. We use the three-dimensional Indirect Boundary Element Method to examine the effects of topography on deformation and gravity changes in models of magma chamber inflation/deflation. Topography has a significant effect on predicted surface deformation and gravity changes. Both the magnitude and pattern of the geodetic signals are significantly different compared to half-space solutions. Thus, failure to account for topographic effects in areas of prominent relief can bias the estimate of volcanic source parameters, since the magnitude and pattern of deformation and gravity changes depend on such effects.     

North Atlantic atmospheric circulation and surface wind in the Northeast of the Iberian Peninsula: uncertainty and long term downscaled variability

The variability and predictability of the surface wind field at the regional scale is explored over a complex terrain region in the northeastern Iberian Peninsula by means of a downscaling technique based on Canonical Correlation Analysis. More than a decade of observations (1992–2005) allows for calibrating and validating a statistical method that elicits the main associations between the large scale atmospheric circulation over the North Atlantic and Mediterranean areas and the regional wind field. In an initial step the downscaling model is designed by selecting parameter values from practise. To a large extent, the variability of the wind at monthly timescales is found to be governed by the large scale circulation modulated by the particular orographic features of the area. The sensitivity of the downscaling methodology to the selection of the model parameter values is explored, in a second step, by performing a systematic sampling of the parameters space, avoiding a heuristic selection. This provides a metric for the uncertainty associated with the various possible model configurations. The uncertainties associated with the model configuration are considerably dependent on the spatial variability of the wind. While the sampling of the parameters space in the model set up moderately impact estimations during the calibration period, the regional wind variability is very sensitive to the parameters selection at longer timescales. This fact illustrates that downscaling exercises based on a single configuration of parameters should be interpreted with extreme caution. The downscaling model is used to extend the estimations several centuries to the past using long datasets of sea level pressure, thereby illustrating the large temporal variability of the regional wind field from interannual to multicentennial timescales. The analysis does not evidence long term trends throughout the twentieth century, however anomalous episodes of high/low wind speeds are identified.     

Estimation of Surface-Layer Scaling Parameters in the Unstable Boundary Layer: Implications for Orographic Flow Speed-Up

A method is proposed for estimating the surface-layer depth \((z_s)\) and the friction velocity \((u_*)\) as a function of stability (here quantified by the Obukhov length, L) over the complete range of unstable flow regimes. This method extends that developed previously for stable conditions by Argaín et al. (Boundary-Layer Meteorol 130:15–28, 2009), but uses a qualitatively different approach. The method is specifically used to calculate the fractional speed-up \((\varDelta S)\) in flow over a ridge, although it is suitable for more general boundary-layer applications. The behaviour of \(z_s \left( L\right) \) and \(u_*\left( L\right) \) as a function of L is indirectly assessed via calculation of \(\varDelta S\left( L\right) \) using the linear model of Hunt et al. (Q J R Meteorol Soc 29:16–26, 1988) and its comparison with the field measurements reported in Coppin et al. (Boundary-Layer Meteorol 69:173–199, 1994) and with numerical simulations carried out using a non-linear numerical model, FLEX. The behaviour of \(\varDelta S\) estimated from the linear model is clearly improved when \(u_*\) is calculated using the method proposed here, confirming the importance of accounting for the dependences of \(z_s\left( L \right) \) and \(u_*\left( L \right) \) on L to better represent processes in the unstable boundary layer.     

Adsorption of cobalt by using inorganic components of sediment samples from water bodies

The adsorption of cobalt ions was evaluated using sediment samples from water bodies to investigate the adsorption properties of sediment and the behavior of these natural materials in the presence of nuclear and industrial waste.The two sediments(S1 and S2)were treated to eliminate humic and fulvic acids and then they were characterized by several techniques.The minerals found in both the sediments(X-ray diffraction)were quartz and albite;plus,goethite and muscovite in S1,and kaolinite and montmorillonite in S2.Point of zero charge(PZC)of S1 and S2 was 6.00 and 5.22,respectively.The specific area of S1(63.3 m²/g)is higher than S2(1.5 m²/g).Adsorption kinetics data for S1 and S2 were best fitted to the pseudo second-order model.The removal efficiency of S1 for cobalt was 96%with an adsorption capacity(qe)of 0.93 mg/g,and for S2 was 45%with a qeof 0.40 mg/g.The experimental data of the adsorption isotherms were adjusted to Langmuir and Freundlich models for S1 and S2,respectively.The thermodynamic parameters(enthalpy,entropy,and Gibb’s free energy)indicated that the adsorption processes were endothermic,spontaneous,and chemisorption mechanism.The results show that the adsorption capacities of the sediments depend on their composition.These water sediments have important adsorption properties for cobalt,and they can be used in the treatment of nuclear and industrial aqueous wastes.     

Predicting the dependency of a degree of saturation on void ratio and suction using effective stress principle for unsaturated soils

The paper presents an approach to predicting variation of a degree of saturation in unsaturated soils with void ratio and suction. The approach is based on the effective stress principle for unsaturated soils and several underlying assumptions. It focuses on the main drying and wetting processes and does not incorporate the effects of hydraulic hysteresis. It leads to the dependency of water retention curve (WRC) on void ratio, which does not require any material parameters apart from the parameters specifying WRC for the reference void ratio. Its validity is demonstrated by comparing predictions with the experimental data on four different soils taken over from the literature. Good correlation between the measured and predicted behaviour indirectly supports applicability of the effective stress principle for unsaturated soils. Copyright © 2009 John Wiley & Sons, Ltd.     

Carbon fluxes through major phytoplankton groups during the spring bloom and post-bloom in the Northwestern Mediterranean Sea

The carbon flux through major phytoplankton groups, defined by their pigment markers, was estimated in two contrasting conditions of the Northwestern Mediterranean open ocean ecosystem: the spring bloom and post-bloom situations (hereafter Bloom and Post-bloom, respectively). During Bloom, surface chlorophyll a (Chl a) concentration was higher and dominated by diatoms (53% of Chl a), while during Post-bloom Synechococcus (42%) and Prymnesiophyceae (29%) became dominant. The seawater dilution technique, coupled to high pressure liquid chromatography (HPLC) analysis of pigments and flow cytometry (FCM), was used to estimate growth and grazing rates of major phytoplankton groups in surface waters. Estimated growth rates were corrected for photoacclimation based on FCM-detected changes in red fluorescence per cell. Given the 30% average decrease in the pigment content per cell between the beginning and the end of the incubations, overlooking photoacclimation would have resulted in a 0.40 d^?1 underestimation of phytoplankton growth rates. Corrected average growth rates (μ_o) were 0.90±0.20 (SD) and 0.40±0.14 d^?1 for Bloom and Post-bloom phytoplankton, respectively. Diatoms, Cryptophyceae and Synechococcus were identified as fast-growing groups and Prymnesiophyceae and Prasinophyceae as slow-growing groups across Bloom and Post-bloom conditions. The higher growth rate during Bloom was due to dominance of phytoplankton groups with higher growth rates than those dominating in Post-bloom. Average grazing rates (m) were 0.58±0.20 d^?1 (SD) and 0.31±0.07 d^?1. The proportion of phytoplankton growth consumed by microzooplankton grazing (m/μ_o) tended to be lower in Bloom (0.69±0.34) than in Post-bloom (0.80±0.08). The intensity of nutrient limitation experienced by phytoplankton indicated by μ_o/μ_n (where μ_n is the nutrient-amended growth rate), was similar during Bloom (0.78) and Post-bloom (0.73). Primary production from surface water (PP) was estimated with ¹⁴C incubations. A combination of PP and Chl a synthesis rate yielded C/Chl a ratios of 34±21 and 168±75 (g:g) for Bloom and Post-bloom, respectively. Transformation of group-specific Chl a fluxes into carbon equivalents confirmed the dominant role of diatoms during Bloom and Synechococcus and Prymnesiophyceae during Post-bloom.