Isolation of resonance in acoustic backscatter from elastic targetsusing adaptive estimation schemes

It has been shown that at certain frequencies the acoustic backscatter from elastic targets exhibits certain resonance behavior which closely relates to the physical properties of the target such as dimension, thickness, and composition. The purpose of this paper is to develop an automated approach for identifying the presence of resonance in the acoustic backscatter from an unknown underwater target by isolating the resonance part from the specular contribution. An adaptive transversal filter structure is used to estimate the specular part of the backscatter and consequently the error signal would provide an estimate of the resonance part. An important aspect of this scheme lies in the fact that it does not require an underlying model for the elastic return. The adaptation rule is based upon fast recursive least squares (RLS) learning. The approach taken in this paper is general in the sense that it can be applied to targets of unknown geometry and thickness and, further, does not require any a priori information about the target and/or the environment. Test results on acoustic data are presented which indicate the effectiveness of the proposed approach     

Spatial measurements of stream baseflow,a relevant method for aquifer characterization and permeability evaluation. Application to a hard‐rock aquifer,the Oman ophiolite

The structure, functioning and hydrodynamic properties of aquifers can be determined from an analysis of the spatial variability of baseflow in the streams with which they are associated. Such analyses are based on simple low‐cost measurements. Through interpreting the hydrological profiles (Q = f(A)) it is possible to locate the aquifer(s) linked to the stream network and to determine the type of interrelated flow, i.e. whether the stream drains or feeds the aquifer. Using an analytical solution developed for situations with a positive linear relationship, i.e. where the baseflow increases linearly with increasing catchment size, it is also possible to estimate the permeability of the aquifer(s) concerned at catchment scale. Applied to the hard‐rock aquifers of the Oman ophiolite, this method shows that the ‘gabbro’ aquifer is more permeable than the ‘peridotite’ aquifer. As a consequence the streams drain the peridotites and ‘leak’ into the gabbro. The hydrological profiles within the peridotite are linear and positive, and indicate homogeneity in the hydrodynamic properties of these formations at the kilometre scale. The permeability of the peridotite is estimated at 5 · 10^?7 to 5 · 10^?8 m/s. Copyright © 2004 John Wiley & Sons, Ltd.     

“BASS 300 PARACOM”: a “model” underwaterparametric communication system

Parametric transduction offers valuable advantages for underwater acoustic communications. Perhaps the most significant benefit is the fact that high directivity is achieved by means of a physically small transmit transducer. This feature may, ultimately, be employed to permit long-range, low-frequency communication using a compact source. The high directivity is desirable to combat multipath propagation and to achieve data communications in water which is shallow by comparison with range. A real-time, high data-rate “model” differential phase shift keying (DPSK) communication system has been constructed and demonstrated. This system uses parametric transduction, with a 300-kHz primary frequency and a 50-kHz secondary frequency. Experimental results show that the system can be employed to combat multipath propagation in shallow water and can achieve high data-rate text and color image transmission at 10 and 20 kb s^-1 for 2-DPSK and 4-DPSK, respectively, through a transmission bandwidth of 10 kHz. The “model” system was developed to confirm performance predictions for a future, operational long-range link employing a 50-kHz primary frequency and a 5-kHz secondary frequency     

OTEC cold-water pipe research

Shelf-mounted Ocean Thermal Energy Conversion (OTEC) plants require installation of cold-water pipes (CWP) on slopes of40degto depths of 1000 m. In addition, tower platforms containing OTEC power systems may be located on lesser sloped terrain near shore and exposed to special environmental loading problems affecting foundation design. Shelf-mounted installations require careful attention to site selection and geotechnical considerations for foundation integrity on sloped surfaces. This paper primarily discusses research associated with cold-water pipe and foundation installations on steep slopes, although research continues on tower platforms located on the shelf. At least five nations are in various stages of development of OTEC systems for island applications. Each of their systems is either shelf mounted or land based and requires that a large diameter cold-water pipe be installed on a steep slope to provide cold water from 1000-m depths. In addition to the installation and deployment of the large cold-water pipe, the most significant problem is the design and installation of suitable foundations that will last for several decades. To date there is very little experience in the offshore industry for large installations on steep slopes. A major scale-model research project is underway on the slopes of the island of Hawaii. A section of pipe 2.4 m in diameter and 24 m long was installed using combination concrete foundations and joints. The pipe and foundations are fully instrumented to measure environmental loading forces due principally to currents and waves. Environmental measurements will also be taken in the test area. The measurement data will be used to validate available analytical models for subsequent use in aiding industry in providing more cost-effective designs for OTEC pipes and foundations.     

The exact theory of inductive conductivity sensors for oceanographic application

The results of a general theoretical investigation of three commonly used types of inductive conductivity sensors, i.e., the single transformer, the double transformer, and the double transformer with an additional loop, are presented. The resulting formulas describe the dependence of the sensor output signal not only on the conductivity of the seawater but also on the parameters of the electrical circuit, among them the permeability of the transformer core(s), which-unlike the other parameters-shifts considerably during oceanographic in situ measurements. A mathematical discussion of these formulas shows that for certain circuit configurations, the sensor output is independent of changes in permeability. Most of these configurations form the basis of existing oceanographical conductivity sensors, among them the "classical" sensors developed by H. Hinkelmann [3], [4], and by N. L. Brown [14], while some others make evident further possibilities for eliminating the unwanted effects of shifting permeability. In the era of microelectronics, the latter might lead to a reassessment, especially of the single transformer-type sensor.     

Axial convergence in a well-mixed estuary

Transverse secondary circulations involving surface convergence, observed in a well-mixed estuary in North Wales, are made visible by the collection of surface material along an axial line which extends continuously for many kilometres through the estuary. The circulation and axial convergence, however, are seen only during the flood phase of the tide and no similar behaviour has been observed during the ebb phase.Convergent circulations in the estuary are associated with small but steady transverse density gradients in the cross-section, produced by non-uniform advection of the longitudinal gradient through the channel. A diagnostic model, using measured mean distributions of cross-sectional density, indicates surface transverse velocities (～0.1 ms^?1) similar to those observed in the estuary. The model further predicts appreciable transverse divergent currents at a fractional depth of 0.75: a prediction which has been tested in the estuary using a vertical array of accurately resolving current direction indicators.     

An approximate method for evaluating the shear band thickness in saturated soils

A formula for the thickness of a shear band formed in saturated soils under a simple shear or a combined stress state has been proposed. It is shown that the shear band thickness is dependent on the pore pressure properties of the material and the dilatancy rate, but is independent of the details of the combined stress state. This is in accordance with some separate experimental observations. Copyright © 2004 John Wiley & Sons, Ltd.     

Age and early metamorphic history of the Sanbagawa belt: Lu–Hf and P–T constraints from the Western Iratsu eclogite

Two distinct age estimates for eclogite-facies metamorphism in the Sanbagawa belt have been proposed: (i) c.  120–110 Ma based on a zircon SHRIMP age for the Western Iratsu unit and (ii) c.  88–89 Ma based on a garnet–omphacite Lu–Hf isochron age from the Seba and Kotsu eclogite units. Despite the contrasting estimates of formation ages, petrological studies suggest the formation conditions of the Western Iratsu unit are indistinguishable from those of the other two units—all ∼20 kbar and 600–650 °C. Studies of the associated geological structures suggest the Seba and Western Iratsu units are parts of a larger semi-continuous eclogite unit. A combination of geochronological and petrological studies for the Western Iratsu eclogite offers a resolution to this discrepancy in age estimates. New Lu–Hf dating for the Western Iratsu eclogite yields an age of 115.9 ± 0.5 Ma that is compatible with the zircon SHRIMP age. However, petrological studies show that there was significant garnet growth in the Western Iratsu eclogite before eclogite facies metamorphism, and the early core growth is associated with a strong concentration of Lu. Pre-eclogite facies garnet (Grt1) includes epidote–amphibolite facies parageneses equilibrated at 550–650 °C and ∼10 kbar, and this is overgrown by prograde eclogite facies garnet (Grt2). The Lu–Hf age of c.  116 Ma is strongly skewed to the isotopic composition of Grt1 and is interpreted to reflect the age of the pre-eclogite phase. The considerable time gap ( c.  27 Myr) between the two Lu–Hf ages suggests they may be related to separate tectonic events or distinct phases in the evolution of the Sanbagawa subduction zone.