Frequency-dependent rupture process,stress change,and seismogenic mechanism of the 25 April 2015 Nepal Gorkha <Emphasis Type="Italic">M</Emphasis><Subscript>w</Subscript> 7.8 earthquake

On 25 April 2015, an M _w 7.8 earthquake occurred on the Main Himalaya Thrust fault with a dip angle of ~ 7° about 77 km northwest of Kathmandu, Nepal. This Nepal Gorkha event is the largest one on the Himalayan thrust belt since 1950. Here we use the compressive sensing method in the frequency domain to track the seismic radiation and rupture process of this event using teleseismic P waves recorded by array stations in North America. We also compute the distribution of static shear stress changes on the fault plane from a coseismic slip model. Our results indicate a dominant east-southeastward unilateral rupture process from the epicenter with an average rupture speed of ~3 km s^?1. Coseismic radiation of this earthquake shows clear frequency-dependent features. The lower frequency (0.05–0.3 Hz) radiation mainly originates from large coseismic slip regions with negative coseismic shear stress changes. In comparison, higher frequency (0.3–0.6 Hz) radiation appears to be from the down-dip part around the margin of large slip areas, which has been loaded and presents positive coseismic shear stress changes. We propose an asperity model to interpret this Nepal earthquake sequence and compare the frequency-dependent coseismic radiation with that in subduction zones. Such frequency-dependent radiation indicates the depth-varying frictional properties on the plate interface of the Nepal section in the main Himalaya thrust system, similar to previous findings in oceanic subduction zones. Our findings provide further evidence of the spatial correlation between changes of static stress status on the fault plane and the observed frequency-dependent coseismic radiation during large earthquakes. Our results show that the frequency-dependent coseismic radiation is not only found for megathrust earthquakes in the oceanic subduction environment, but also holds true for thrust events in the continental collision zone.     

2015年四川乐山金口河M5.0地震孕震构造条件分析

2015年1月14日乐山金口河M5.0地震发生在历史地震强度较低的川南山区与四川盆地交界一带。基于四川区域地震台网的震相报告与波形资料,采用双差定位法对地震序列进行重新定位,同时,采用CAP波形反演方法及HASH方法反演了主震及序列中8次M_L≥2.0地震的震源机制解。另外,利用Coulomb3计算了主震发生后库仑应力改变量,得到的结果如下：①重新定位结果显示,金口河M5.0地震位于（103.18°E,29.32°N）,震源深度16.6km,略深于波形反演结果（12km）。序列分布在NNW向天全-荥经断裂和NE向西河-美姑断裂的交汇部位,余震序列在空间上呈NE向展布。②M5.0主震的机制解为节面Ⅰ：走向350°/倾角46°/滑动角107°,节面Ⅱ：走向146°/倾角47°/滑动角73°,表现为走向NW（NNW）、中等倾角的逆冲型运动方式。序列中其余8次M_L≥2.0余震大多以走向NE的逆冲型地震为主,个别为走滑或正断层类型。主震和大部分余震的节面方向不一致,主震节面方向与余震长轴方向也不一致。③主震后库仑应力改变量显示,余震主要发生在主震引起的库仑破裂应力增加的区域。综合分析推测,NNW向天全-荥经断裂为本次地震主震的发震构造,倾向NE的机制解节面Ⅰ指出了该断裂的几何产状;M5.0主震发生后,立即触发了其旁侧的NE向西河-美姑断裂,并激发了多次余震。     

Mobile Agent系统结构及其关键技术

Mobile Agent技术是一门新兴的技术,具有移动性、智能性和异步计算的特点,已成为计算机网络和分布式系统最具活力的发展方向.现对Mobile Agent的概念、系统结构及其关键技术进行了分析和探讨.     

三维区域地面沉降数值模拟

由于地裂缝研究及地表变形监测技术（例如GPS,InSAR等）的快速发展,抽取地下水引起的地层水平位移受到关注。传统区域地面沉降模型虽然求解快速但不能模拟水平位移;比奥模型虽然能够模拟土体的三维变形,但模型求解的计算量较大,较少应用于大尺度的区域地面沉降数值模拟。为解决以上问题,推导了解耦三维地面沉降数学模型,模型推导过程显示：比奥模型假设法向总应力和不变,则可简化为解耦三维地面沉降模型;解耦三维地面沉降模型假设土体仅有垂向一维变形,则可简化为传统区域地面沉降模型。同时通过数值试验验证了解耦三维地面沉降模型可以作为比奥模型的替代模型和传统区域地面沉降模型的改进模型,用来模拟抽取地下水引起的三维区域地面沉降。     

Features of the Extremely Severe Drought in the East of Southwest China and Anomalies of Atmospheric Circulation in Summer 2006

The spatial-temporal features of the extremely severe drought and the anomalous atmospheric circulation in summer 2006 are analyzed based on the NCEP/NCAR reanalysis data, the characteristic circulation indices given by the National Climate Center of China, and the daily precipitation data of 20 stations in the east of Southwest China (ESC) from 1959 to 2006. The results show that the rainless period started from early June and ended in early September 2006 with a total of more than 80 days, and the rainfall was especially scarce from around 25 July to 5 September 2006. Precipitation for each month was less than normal, and analysis of the precipitation indices shows that the summer precipitation in 2006 was the least since 1959. The extremely severe drought in the ESC in summer 2006 was closely related to the persistent anomalies of the atmospheric circulation in the same period, i.e., anomalies of mid-high latitude atmospheric circulation, western Pacific subtropical high (WPSH), westerlies, South Asian high, lower-level flow, water vapor transport, vertical motion, and so on. Droughts usually occur when the WPSH lies anomalously northward and westward, or anomalously weak and eastward. The extreme drought in summer 2006 was caused by the former. When the WPSH turned stronger and shifted to the north and west of its normal position, and the South Asian high was also strong and lay eastward, downdrafts prevailed over the ESC and suppressed the water vapor transfer toward this area. At the same time, the disposition of the westerlies and the mid-high latitude circulation disfavored the southward invasion of cold air, which jointly resulted in the extremely severe drought in the ESC in summer 2006. The weak heating over the Tibetan Plateau and vigorous convective activities over the Philippine area were likely responsible for the strong WPSH and its northwestward shift in summer 2006.     

分形在地貌学中应用的几个问题的分析

就实际地貌分形研究工作中经常遇到的截面约定、自仿射分形局域维与渡越长度、分维的比较以及过渡分形等几个问题进行了分析和探讨，并提出了在应用过程中的注意事项和解决方案。     

Seismic behavior of self-centering reinforced concrete wall enabled by superelastic shape memory alloy bars

Reinforced concrete (RC) wall is a common type of structural component used in high-rise buildings to resist lateral loads induced by earthquakes. RC walls are typically designed and detailed to dissipate energy through significant inelastic responses to meet expected seismic performance under moderate-to-strong earthquakes. However, costly repair or even demolition caused by excessive residual deformation is usually inevitable. Given this deficiency, this study investigates the feasibility of utilizing superelastic shape memory alloy (SMA) bars to achieve self-centering (SC) RC walls. Under this condition, the residual deformation of SC–RC walls is reduced by superelastic SMA with large recoverable strain and remarkable fatigue properties. The mechanical properties of superelastic nickel–titanium bars and SC–RC wall design are described. A numerical SC–RC wall model is developed and validated by comparing the test results. Parametric studies of SC–RC wall systems are then conducted to investigate the effects of axial compressive load ratio, bottom slit length, and lower plateau stress factor of SMA. Results show that the proposed SC–RC walls have excellent SC ability and moderate energy dissipation capacity. The damage regions and levels of the SC–RC wall systems are also discussed.     

Characteristics and variations of the East Asian monsoon system and its impacts on climate disasters in China

Recent advances in studies of the structural characteristics and temporal-spatial variations of the East Asian monsoon （EAM） system and the impact of this system on severe climate disasters in China are reviewed. Previous studies have improved our understanding of the basic characteristics of horizontal and vertical structures and the annual cycle of the EAM system and the water vapor transports in the EAM region. Many studies have shown that the EAM system is a relatively independent subsystem of the Asian- Australian monsoon system, and that there exists an obvious quasi-biennial oscillation with a meridional tripole pattern distribution in the interannual variations of the EAM system. Further analyses of the basic physical processes, both internal and external, that influence the variability of the EAM system indicate that the EAM system may be viewed as an atmosphere-ocean-land coupled system, referred to the EAM climate system in this paper. Further, the paper discusses how the interaction and relationships among various components of this system can be described through the East Asia Pacific （EAP） teleconnection pattern and the teleconnection pattern of meridional upper-tropospheric wind anomalies along the westerly jet over East Asia. Such reasoning suggests that the occurrence of severe floods in the Yangtze and Hualhe River valleys and prolonged droughts in North China are linked, respectively~ to the background interannual and interdecadal variability of the EAM climate system. Besides, outstanding scientific issues related to the EAM system and its impact on climate disasters in China are also discussed.     

Nonsulfide zinc deposits in the Silesia–Cracow district,Southern Poland

The Silesia–Cracow district in Poland has been one of the world’s principal sources of zinc from nonsulfide zinc ore (Polish: galman). The still remaining nonsulfide ore resources can be estimated at 57 Mt at 5.6% Zn and 1.4% Pb. Nonsulfide mineralization is mainly hosted by Lower Muschelkalk (Triassic) limestone and is associated with different generations of the hydrothermal ore-bearing dolomite (OBD I, II, III). A fundamental ore control is believed to have been exerted by the basement faults, which were repeatedly reactivated during the Alpine tectonic cycle, leading to the formation of horst-and-graben structures: these dislocations may have caused short periods of emersion and the circulation of meteoric waters during the Cenozoic. Nonsulfide ores show a wide range of morphological characteristics and textures. They occur as earthy masses, crystalline aggregates, and concretions in cavities. Breccia and replacement textures are also very common. The most important mineral phases are: smithsonite, Fe–smithsonite, Zn–dolomite, goethite, and Fe–Mn(hydr)oxides. Minor hemimorphite and hydrozincite have also been detected. Two distinct nonsulfide ore types occur: the predominant red galman and the rare white galman. In the white galman, Fe–smithsonite and Zn–dolomite are particularly abundant. This ore type is commonly considered as a peripheral hydrothermal alteration product related to the same fluids that precipitated both the OBD II–III and the sulfides. In contrast, a supergene origin is commonly assumed for the red galman. Evidence of the petrographic and mineralogical difference between white and red galman is also found in stable isotope data. Smithsonite from red galman shows a limited range of δ ¹³C_VPDB values (−10.1 to −11.4‰), and δ ¹⁸O_VSMOW values (25.3‰ to 28.5‰, mean 26.8 ± 0.3‰). The uniform and low carbon isotope values of red galman smithsonite are unusual for supergene carbonate-hosted deposits and indicate the predominance of a single organic carbon source. Smithsonite from white galman has a more variable, slightly more positive carbon isotope (−2.9‰ to −7.4‰), but broadly similar oxygen isotope composition (26.8‰ to 28.9‰). The relationship of the white galman ore with the hydrothermal system responsible for OBD II and sulfide generation is still uncertain. The most important paleoweathering events took place in both Lower and Upper Silesia during Late Cretaceous up to Paleogene and early Neogene time. During this period, several short-lasting emersions and intense weathering episodes facilitated the formation of sinkholes in the Triassic carbonate rocks and the oxidation of sulfide orebodies through percolating meteoric waters. These phenomena may have lasted until the Middle Miocene.     

Monitoring Large-Scale Tests for Nuclear Waste Disposal

Two large-scale “in situ” demonstration experiments and their instrumentation are described. The first test (FEBEX Experiment) involves the hydration of a compacted bentonite barrier under the combined effect of an inner source of heat and an outer water flow from the confining saturated granite rock. In the second case, the progressive de-saturation of Opalinus clay induced by maintained ventilation of an unlined tunnel is analyzed. The paper shows the performance of different sensors (capacitive cells, psychrometers, TDR’s) and a comparison of fill behaviour with modelling results. The long term performance of some instruments could also be evaluated specially in the case of FEBEX test. Capacitive sensors provide relative humidity data during long transient periods characterised by very large variations of suction within the bentonite.