Electrodialytic treatment of sewage sludge: influence on microbiological community

This study aimed to evaluate the changes in microbiological communities present in sewage sludge (SS) when subjected to an electric field. The establishment of these relations is important to design and optimize an electrotechnology that not only promotes a direct degradation of the emerging organic contaminants, through electrodegradation, but also stimulates their biodegradation. Different current intensities were used continuously or by steps, in a two compartment electrodialytic (ED) cell. Samples collected between May and July of 2015 were analysed, prior to ED treatment, and the 35 Taxa identified were divided in 12 groups. Initial samples, collected on May, were mainly constituted by stalked ciliates (86%), followed by shelled amoebae (8%), whereas the samples collected between June and July presented higher number of shelled amoebae, between 52 and 92%. Epistylis, Vorticella and Arcella gibbosa were the most frequent protozoa identified. Samples richness (R) was between 7 and 14, Simpson’s biodiversity index (D) between 0.45 and 0.69, and evenness between 0.42 and 0.65. At the end of the ED experiments, a decrease in the number of identified Taxa and individuals was observed and, consequently, SS biodiversity also decreased. This decline was more pronounced in the ED experiments conducted with currents above 50 mA (0.10 mA cm^?2). In terms of abundance, the final SS was mainly constituted by shelled amoebae that showed to be the most resistant to the conditions within the ED cell. The obtained results showed that the studied conditions within the ED cell were not appropriate to the microbiological communities, which influenced the final SS quality.     

Reassessment of Hydrofluoric Acid Desilicification in the Carius Tube Digestion Technique for Re–Os Isotopic Determination in Geological Samples

In this study, Re and Os isotopes were systematically determined in six geological reference materials (RMs; covering a wide range of lithologies) using the Carius tube (CT) digestion technique with and without hydrofluoric acid desilicification. Our results show that the HF desilicification increased the Re extraction efficiency (by 9–15%) evidenced from basaltic and andesitic rocks (e.g., BHVO‐2, TDB‐1 and AGV‐2). This implies that a small proportion of Re resides in silicate phases. For mafic–ultramafic rocks (e.g., BCR‐2, WGB‐1 and WPR‐1), Re extraction efficiencies obtained by the CT digestion with and without HF desilicification were similar. This may indicate that Re in these rocks may dominantly reside in some phases (e.g., magnetite and sulfides) that could be completely dissolved in aqua regia solutions without the aid of HF desilicification. Our results also show that the HF desilicification increased Os extraction efficiency (by 13–99%) in some RMs (e.g., BHVO‐2, WGB‐1 and AGV‐2). This observation suggests that a portion of Os‐rich trace phases may occur as inclusions in the silicate phases that act as isolators at ~ 200 mesh sizes. This study demonstrates that the HF desilicification step prior to CT digestion is important for complete extraction of Re and Os in geological samples.     

Grain‐size variability within a mega‐scale point‐bar system,False River,Louisiana

Point bars formed by meandering river systems are an important class of sedimentary deposit and are of significant economic interest as hydrocarbon reservoirs. Standard point‐bar models of how the internal sedimentology varies are based on the structure of small‐scale systems with little information about the largest complexes and how these might differ. Here a very large point bar (>25·0 m thick and 7·5 × 13·0 km across) on the Mississippi River (USA) was examined. The lithology and grain‐size characteristics at different parts of the point bar were determined by using a combination of coring and electrical conductivity logging. The data confirm that there is a general fining up‐section along most parts of the point bar, with a well‐defined transition from massive medium‐grained sands below about 9 to 11 m depth up into interbedded silts and fine–medium sand sediment (inclined heterolithic strata). There is also a poorly defined increase in sorting quality at the transition level. Massive medium sands are especially common in the region of the channel bend apex and regions upstream of that point. Downstream of the meander apex, there is much less evidence for fining up‐section. Finer sediment accumulated more readily after the establishment of a compound bar in the later stages of construction, at the terminal apex and in the bar tail. This work implies that the best reservoir sands are likely to be located in the centre of the point bar, deposited in a simple bar system. Reservoir quality decreases towards the bar edge. The early‐stage channel plug is largely composed of coarsening‐upward cycles of silt to clay and is dominated by clay and clayey silt material with poor reservoir characteristics.     

Hydromechanical reactivation of natural discontinuities: mesoscale experimental observations and DEM modeling

Fracture interaction mechanisms and reactivation of natural discontinuities under fluid pressurization conditions can represent critical issues in risk assessment of caprock integrity. A field injection test, carried out in a damage fault zone at the decameter scale, i.e., mesoscale, has been studied using a distinct element model. Given the complex structural nature of the damage fault zone hydraulically loaded, the contribution of fracture sets on the bulk permeability has been investigated. It has been shown that their orientation for a given in situ stress field plays a major role. Based on these results, a simpler model with a fluid-driven fracture intersecting a second fracture has been set up to perform a sensitivity analysis. It is in presence of a minimum differential stress value with a minimum angle with the maximum principal stress that the second fracture could be both, hydraulically and mechanically reactivated. Results also showed that in the vicinity of the fluid-driven fracture, a natural fracture will offer contrasted hydromechanical responses on each side of the intersection depending on the stress conditions and its orientation with respect to the stress field. In this case, we show that a hydromechanical decoupling can occur along the same plane. These results provide insights into fracture-controlled permeability of fault zones depending on the properties of the fractures and their hydromechanical interactions for a given in situ stress field.

     

Evaluation of Zerovalent Zinc for Treatment of 1,2,3‐Trichloropropane‐Contaminated Groundwater: Laboratory and Field Assessment

The efficacy and feasibility of using zerovalent zinc (ZVZ) to treat 1,2,3‐trichloropropane (TCP)‐contaminated groundwater was assessed in laboratory and field experiments. In the first portion of the study, the reactivity of commercially available granular ZVZ toward TCP was measured in bench‐scale batch‐reactor and column experiments. These results were used to design columns for on‐site pilot‐scale treatment of contaminated groundwater at a site in Southern California. Two of the ZVZ materials tested were found to produce relatively high rates of TCP degradation as well as predictable behavior when scaling from bench‐scale to field testing. In addition, there was little decrease in the rates of TCP degradation over the duration of field testing. Finally, no secondary impacts to water quality were identified. The results suggest that ZVZ may be an effective and feasible material for use in engineered treatment systems, perhaps including permeable reactive barriers.     

Comparison of surface seismic sources at the CO2SINK site, Ketzin, Germany

In 2004 three seismic surface sources (VIBSIST, accelerated weight drop and MiniVib) were tested in a pilot study at the Ketzin test site, Germany, a study site for geological storage of CO₂ (EU project CO₂SINK). The main objectives of this pilot study were to 1) evaluate the response of the Ketzin site to reflection seismics, especially at the planned injection depth, 2) test different acquisition parameters and 3) use the results to guide the planning of the 3D survey. As part of these objectives, we emphasize the source performance comparison in this study. The sources were tested along two perpendicular lines of 2.4 km length each. Data were acquired by shooting at all stations (source and receiver spacing of 20 m) on both lines, allowing common‐midpoint stacked sections to be produced. The sources' signal characteristics based on signal‐to‐noise ratio, signal penetration and frequency content of raw shot records were analysed and stacked sections were compared. The results show that all three surface sources are suitable for reflection seismic studies down to a depth of about 1 km and provide enough bandwidth for resolving the geological targets at the site, i.e., the Weser and Stuttgart Formations. Near surface conditions, especially a thick weathering layer present in this particular area, strongly influence the data quality, as indicated by the difference in reflectivity and signal‐to‐noise ratio of the two common‐midpoint lines. The stacked sections of the MiniVib source show the highest frequency signals down to about 500 ms traveltime (approximately 500 m depth) but also the shallowest signal penetration depth. The VIBSIST source generates signals with the highest signal‐to‐noise ratio and greatest signal penetration depth of the tested sources. In particular, reflections below 900 ms (approximately 1 km depth) are best imaged by the VIBSIST source. The weight drop performance lies in between these two sources and might be recommended as an appropriate source for a 3D survey at this site because of the shorter production time compared to the VIBSIST and MiniVib sources.     

Controls on carbon and nitrogen export in an eroding catchment of south‐eastern Queensland,Australia

Effects of gully and channel erosion on the export of sediments are in general well understood, but the effects on carbon (C) and nitrogen (N) export remain an open question. We examined these effects and the role of flow magnitude, total wet season rainfall, catchment size and the C and N content and solubility of most probable sediment sources in a subtropical catchment. We sampled the baseflow and the rising stage of high‐flow events for one wet season and analysed 5 years of water quality data from event sampling stations. Total suspended sediment was the main variable explaining N export followed by rainfall, flow and catchment size. N was exported mainly in particulate organic form and C in dissolved form. The quality of most probable sediment source fractions explains these results and points to fractionation during transport into C and N richer and C and N poorer fractions, with travel distance ultimately determining the average quality of transported sediment for different flow magnitudes. Erosion would have caused a lower C and N concentration in sediments, a lower proportion of mineralized N, a larger proportion of dissolved organic C and a larger C : N ratios of the soluble fraction as compared with unincised grassed valleys. This would alter the rates of nutrient cycling and energy flow within and across ecosystem compartments in streams receiving this export. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigating the effects of a summer storm on the North Sea stratification using a regional coupled ocean-atmosphere model

The influence of a summer storm event in 2007 on the North Sea and its effects on the ocean stratification are investigated using a regional coupled ocean (Regional Ocean Modeling System, ROMS)-atmosphere (Weather Research & Forecasting model, WRF) modeling system. An analysis of potential energy anomaly (PEA, Φ) and its temporal development reveals that the loss of stratification due to the storm event is dominated by vertical mixing in almost the entire North Sea. For specific regions, however, a considerable contribution of depth-mean straining is observed. Vertical mixing is highly correlated with wind induced surface stresses. However, peak mixing values are observed in combination with incoming flood currents. Depending on the phase between winds and tides, the loss of stratification differs strongly over the North Sea. To study the effects of interactive ocean-atmosphere exchange, a fully coupled simulation is compared with two uncoupled ones for the same vertical mixing parameters to identify the impact of spatial resolution as well as of SST feedback. While the resulting new mixed layer depth after the storm event in the uncoupled simulation with lower spatial and temporal resolution of the surface forcing data can still be located in the euphotic zone, the coupled simulation is capable to mix the entire water column and the vertical mixing in the uncoupled simulation with higher resolution of the surface forcing data is strongly amplified. These differences might have notable implications for ecosystem modeling since it could determine the development of new phytoplankton blooms after the storm and for sediment modeling in terms of sediment mobilization. An investigation of restratification after the extreme event illustrates the persistent effect of this summer storm.