Linking Remote-Sensing and <Emphasis Type="Italic">In Situ</Emphasis> Observations of Coronal Mass Ejections Using STEREO

The twin STEREO spacecraft have been observing the Sun since 2006. Even though STEREO has only been active during solar minimum conditions so far, an important number of coronal mass ejections (CMEs) and their interplanetary counterparts (ICMEs) have been observed. Many of the ICMEs can be linked back to the corresponding CMEs on the Sun through the combination of remote-sensing and in situ observations. This paper aims to answer the question whether a CME observed by a coronagraph will be detected in situ by a spacecraft in a specific location in the heliosphere. We use a flux-rope-like model fit to the STEREO SECCHI/COR2 data to obtain the direction of CME propagation and its geometrical configuration in three dimensions. Based on model parameters, we then calculate their angular widths and determine whether they should have been detected by STEREO-A, STEREO-B, Wind or ACE. We compare the results with corresponding in situ observations of ICMEs. We find that predictions of ICME detections on the base of COR2 data generally match well the actual in situ observations.     

Potential martian mineral resources: Mechanisms and terrestrial analogues

The future exploration of Mars is likely to utilize resources that can be extracted in situ. An overview of the geology of Mars has been presented and several mechanisms that could result in the formation of ore deposits have been identified. These include deposits caused by hydrothermal fluids resulting from volcanic activity, large igneous province formation and impact craters. Surface enrichment of mineral sand deposits is also discussed. Where appropriate, terrestrial analogues of these mechanisms have been discussed and supporting evidence from observations of Mars undertaken to date presented. Types of deposits that are unlikely to be found on Mars are also listed.     

The use of reference models from a priori data to guide 2D inversion of electrical resistivity tomography data

Clay-rich till plains cover much of the UK. Such sites are attractive locations for landfills, since clay aquitards lower the risk of landfill leachate entering groundwater. However, such tills often contain sand and gravel bodies that can act as leachate flow routes. Such bodies may not be detected by conventional site investigation techniques such as drilling boreholes and trial pitting. A method of guided inversion, where a priori data are used to construct structural reference models for use in inverting electrical resistivity tomography data, was proposed as a tool to improve the detection of sand and gravel bodies within clay-rich till sequences.
Following a successful 2D guided inversion synthetic modelling study, a field study was undertaken. Wenner 2D electrical resistivity tomography lines, resistivity cone penetrometry bores and electromagnetic induction ground resistivity data were collected over a site on the East Yorkshire coast, England, where sand and gravel lenses were known to exist from cliff exposures. A number of equally valid geoelectrical models were constructed using the electromagnetic and resistivity cone data. These were used as structural reference models in the inversion of the resistivity tomography data. Blind inversion using an homogenous reference model was also carried out for comparison.
It was shown for the first time that the best solution model produced by 2D inversion of one data set with a range of structural reference models could be determined by using the l ₂ model misfit between the solution models and associated reference models (reference misfit) as a proxy for the l ₂ misfit between the solution models and the synthetic model or 'best-guess' geoelectrical model (true misfit). The 2D methodology developed here is applicable in clay-rich till plains containing sand and gravel bodies throughout the UK.     

Bound and mobile soil water isotope ratios are affected by soil texture and mineralogy,whereas extraction method influences their measurement

Questions persist about interpreting isotope ratios of bound and mobile soil water pools, particularly relative to clay content and extraction conditions. Interactions between pools and resulting extracted water isotope composition are presumably related to soil texture, yet few studies have manipulated the bound pool to understand its influence on soil water processes. Using a series of drying and spiking experiments, we effectively labelled bound and mobile water pools in soils with varying clay content. Soils were first vacuum dried to remove residual water, which was then replaced with heavy isotope-enriched water prior to oven drying and spiking with heavy isotope-depleted water. Water was extracted via centrifugation or cryogenic vacuum distillation (at four temperatures) and analysed for oxygen and hydrogen isotope ratios via isotope ratio mass spectrometry. Water from centrifuged samples fell along a mixing line between the two added waters but was more enriched in heavy isotopes than the depleted label, demonstrating that despite oven drying, a residual pool remains and mixes with the mobile water. Soils with higher clay + silt content appeared to have a larger bound pool. Water from vacuum distillation samples have a significant temperature effect, with high temperature extractions yielding progressively more heavy isotope-enriched values, suggesting that Rayleigh fractionation occurred at low temperatures in the vacuum line. By distinctly labelling bound and mobile soil water pools, we detected interactions between the two that were dependent on soil texture. Although neither extraction method appeared to completely extract the combined bound and mobile (total water) pool, centrifugation and high temperature cryogenic vacuum distillations were comparable for both δ²H and δ¹⁸O of soil water isotope ratios.     

Unveiling buried aeolian landscapes: reconstructing a late Holocene dune environment using 3D ground-penetrating radar

Across the UK, sandy beaches and dunes protect coastal infrastructure from waves and extreme water levels during large-scale storms, while providing important habitats and recreational opportunities. Understanding their long-term evolution is vital in managing their condition in a changing climate. Recently, ground-penetrating radar (GPR) methods have grown in popularity in geomorphological applications, yielding centimetre-scale resolution images of near-surface stratigraphy and structure, thus allowing landscape evolution to be reconstructed. Additionally, abrupt changes in palaeo-environments can be visualized in three dimensions. Although often complemented by core data, GPR allows interpretations to be extended into areas with minimal ground-truth control. Nonetheless, GPR data interpretation can be non-intuitive and ambiguous, and radargrams may not initially resemble the expected subsurface geometry. Interpretation can be made yet more onerous when handling the large 3D data volumes that are facilitated with modern GPR technology. Here we describe the development of novel semi-automated GPR feature-extraction tools, based on ‘edge detection’ and ‘thresholding’ methods, which detect regions of increased GPR reflectivity which can be applied to aid in the reconstruction of a range Quaternary landscapes. Since reflectivity can be related to lithological and/or pore fluid changes, the 3D architecture of the palaeo-landscape can be reconstructed from the features extracted from a geophysical dataset. We present 500 MHz GPR data collected over a buried Holocene coastal dune system in North Wales, UK, now reclaimed for use as an airfield. Core data from the site, reaching a maximum depth 2 m, suggest rapid vertical changes from sand to silty-organic units, and GPR profiles suggest similar lateral complexity. By applying thresholding methods to GPR depth slices, these lateral complexities are effectively and automatically mapped. Furthermore, automatic extraction of the local reflection power yields a strong correlation with the depth variation of organic content, suggesting it is a cause of reflectivity contrast. GPR-interpolated analyses away from core control thus offer a powerful proxy for parameters derived from invasive core logging. The GPR data collected at Llanbedr airfield highlight a complex dune system to a depth of 2.8 m, probably deposited in several phases over ~700 years, similar to elsewhere in North Wales.     

Longitudinal dispersion processes in the upper tamar estuary

Measurements of velocity, salinity, and suspended solids concentration have been used to investigate the intra-tidal variation of vertical and transverse shear-induced dispersion. For the study research the interaction of the longitudinal density gradient and vertical shear during the early part of the ebb tide accounted for much of the net longitudinal dispersion of solute landward. The same mechanism also is shown to lead to a net particulate transport landward. The landward flux, however, takes place during the flood tide. The field data are also used to elucidate the tidally averaged tidal pumping mechanism.