Deep-ocean vertical noise directionality

The structure of beam noise measured at the output of a vertical array in a range dependent ocean basin was investigated using the modified wide-angle parabolic equation (PE). Noise sources were distributed throughout the basin, and the field due to each noise source at an array located in the midbasin was calculated. The response of the array to the superposition of the noise sources was found by beamforming. An efficient and direct approach that superimposes the noise sources on the PE field as the field is marched toward the array was developed. Downslope calculations of the midbasin vertical directionality were made between 50 and 400 Hz with this technique. Use of a geoacoustic model shows that the bottom behaves as a low-pass filter     

Inverted echo sounder measurement of dynamic height through an ENSOcycle in the central equatorial Pacific

A four-year record from an inverted echo sounder deployed near Palmyra Island at 6°N in the central Pacific Ocean is compared with a simultaneous record of subsurface pressure from this island lagoon. A factor m, converting round-trip acoustic travel time to surface dynamic height relative to a deep pressure level, was estimated from the ratio of the spectra of the two records in the energetic synoptic oscillation band. Year-to-year variation in m was not statistically significant. For the overall record, m was found to be -70±8 dynamic m/s, where the error bounds represent a 90% confidence interval. This is consistent with first-baroclinic-mode excitation     

Magma homogenization during anatexis,ascent and/or emplacement? Constraints from the Variscan Weinsberg Granites

Recent studies have shown that melts and residues may not equilibrate during anatexis, and uncertainty exists about the scale on which magmas can be homogenized. This study of elemental and isotopic homogeneity of the South Bohemian Weinsberg granites (˜ 5000 km²) identifies three voluminous, relatively homogeneous magma batches. Each batch has different ⁸⁷Sr/⁸⁶Sr_init (0.7080, 0.7093 and 0.7106), but all equilibrated at ˜ 327–329 Ma, very similar to the time of monazite crystallization. The data cannot entirely prove melt/residue equilibration during anatexis. However, elemental and isotopic compositions imply magma generation by partial melting of heterogeneous South Bohemian crust and chemical differentiation subsequent to Sr-isotope equilibration. Assuming relatively rapid ascent and solidification rates, magma homogenization must have occurred mostly just after partial melting, during melt segregation and accumulation in the deeper crust with slow prograde heating. Models of rapid crustal heating and instantaneous melt extraction are incompatible with the data.     

A comparison of type II shock speeds

Type II radio bursts are produced by material moving outwards in the solar atmosphere. Their drift in frequency allows the calculation of the radial speed with which the shock is moving- very basic information in assessing the likelihood that the shock will reach the Earth and its time of arrival. This paper compares the shock speeds derived from radio bursts observed by the Swept Frequency Interferometric Radiometer (SFIR) equipment at the US Air Force Radio Solar Telescope Network (RSTN) of observatories with those measured with the Culgoora radiospectrograph operated by IPS Radio and Space Services. The SFIR shock speeds are found to be 1.5–3.0 times larger than the Culgoora values which are consistent with earlier results. This difference appears to originate from the incorrect interpretation of events as a result of the smaller frequency range of the SFIR equipment.     

Wooden Panel Deterioration by Tropical Marine Wood Borers

Wood destruction in test panels ofShorea leprosulawas related to the percentage of fouling, types of wood borers and the number of wood borers. The natural durability ofShorea leprosulapanels was estimated to be 4–5 months in Malaysian marine waters. A higher fouling cover resulted in lower rates of wooden panel deterioration. Larger numbers of wood borers brought about greater panel deterioration. Primary wood destruction was caused by bivalve wood borers, mainlyMartesia striata, Lyrodus pedicellatus, Bankia campanellata, Teredo furciferaandTeredo bartschi. Martesia striatawas the important wood destroying agent in the intertidal zone and, together with the shipworms, was also responsible for panel destruction in the subtidal zone.     

Some Problems with Slow Rotation of CP Stars

Some difficulties in explaining the slow rotation of CP stars are discussed. The most likely hypotheses are (1) a loss of angular momentum involving a magnetic field during “pre-main sequence” evolution and (2) the slow rotation existed from the very start of the creation of these stars. The braking hypothesis is supported by only one property of CP stars— the lower the mass of the star is, the greater the difference between its average rotation velocity vsini and that of normal stars. On the other hand, there is another property— the lower the rotation speeds of CP stars are, the greater their fraction among normal stars. The latter property supports the hypothesis that the lower the initial rotation speed of a star is when it is created, the greater the probability will become chemically peculiar. This property is inherent in chemically peculiar stars both with and without a magnetic field. It is proposed that the cause of the slow rotation of CP stars must be sought in the very earliest phases of their formation, as should the cause of the separation into chemically peculiar magnetic, chemically peculiar nonmagnetic, and normal stars.__________Translated from Astrofizika, Vol. 48, No. 2, pp. 229–245 (May 2005).     

Effect of element size on the static finite element analysis of steep slopes

The accuracy of the computed stress distribution near the free surface of vertical slopes was evaluated in this study as a function of the element size, including aspect ratio. To accomplish this objective, a parametric study was carried out comparing stresses computed using the finite element method (FEM) to those obtained from a physical model composed of photoelastic material. The results of the study indicate a reasonable agreement between a gelatin model and the FEM model for shear stresses, and an overall good agreement between the two models for the principal stresses. For stresses along the top of the slope, the height of the element tends to be more important than width or aspect ratio, at least for aspect ratios up to 4. In all cases, the greatest difference between the two models occurs in the vicinity of the slope. Specifically, if H is defined as the slope height, an element height of H/10 appears to be adequate for the study of stresses deep within the slope, such as for typical embankment analyses. However, for cases where tensile stresses in the vicinity of the slope face which are critical, such as for the stability analysis of steep slopes, element heights as small as H/32, or higher‐order elements, are necessary. Copyright © 2001 John Wiley & Sons, Ltd.     

Ambipolar diffusion in the solar atmosphere

The process of non-linear ambipolar diffusion in the region overlying the solar surface can be an effective mechanism for producing sharp magnetic structures and current sheets. These may be the sites responsible for the occurrence of connectivity of magnetic field lines, and the subsequent explosive input of energy for heating of some of the features in the atmosphere of the Sun..