Design of stable drainage networks in upland forestry plantations

Erosion of man-made, forestry drainage channels occurs when the plough cuts through the surface peat layer into the underlying erodible mineral soil. A procedure is developed, based on hydraulic considerations, which will allow the drainage engineer to design stable drainage networks in upland forestry plantations. An example design chart is given for an erodible sandy loam type soil.     

A simulation tool for high data-rate acoustic communication in ashallow-water, time-varying channel

The paper discusses the development of a simulation tool to model high data-rate acoustic communication in shallow water. The simulation tool is able to generate synthetic time series of signals received at a transducer array after transmission across a shallow-water communication channel. The simulation tool is suitable for testing advanced signal processing techniques for message recovery. A channel model has been developed based on the physical aspects of the acoustic channel. Special emphasis has been given to fluctuations of the signal transmission caused by time-varying multipath effects. At shorter ranges, the temporal variations are dominated by acoustic scattering from the moving sea surface. Therefore, the channel model produces a coherence function which may be interpreted as a time-varying reflection coefficient for the surface scattered acoustical path. A static, range-independent ray model identifies the significant multipaths, and the surface path is modulated with the time-varying reflection coefficient. The advantages and limitations of the channel model are discussed and assumptions necessary to overcome the limitations are emphasised. Based on the assumptions, an algorithm has been developed and implemented to model how a binary message will be modulated when transmitted by a transducer, is distorted in the channel and finally is received by a transducer array     

Isobaric cooling and anti-clockwise P–T paths in the Variscan Odenwald Crystalline Complex, Germany

Mineral assemblages in Al₂O₃‐rich, SiO₂‐ and K₂O‐poor metapelitic rocks from the western Odenwald Crystalline Complex (Variscan Mid‐German Crystalline Rise, southern Germany) include corundum, spinel, cordierite, sillimanite, garnet and staurolite. Quartz is absent from almost all samples. Therefore, the applicability of conventional geothermobarometry is very limited or even impossible. Detailed petrographic investigation on selected samples permits inference of the sequence of appearance and disappearance of several mineral assemblages. The recognition of such partial re‐equilibration stages and their associated mineral assemblages, together with mineral stabilities predicted from KFMASH pseudosections, enables the determination of the pressure‐temperature (P–T) trajectories experienced by these rocks during the Variscan metamorphism. The rocks were metamorphosed under low‐P/high‐T conditions and underwent an anti‐clockwise P–T evolution. A pressure increase from about 2 kbar to 4 ± 0.5 kbar was accompanied by heating. Peak metamorphic conditions were reached at pressures of 4 ± 0.5 kbar and temperatures of at least 640 °C, probably even higher. The retrograde evolution is characterised by near‐isobaric cooling from ≥ 640 °C to approximately 550 °C. The rocks underwent the anti‐clockwise evolution in a subduction‐related magmatic arc setting. The close spatial association of the low‐P/high‐T rocks with recently discovered metabasic eclogites in the eastern part of the Odenwald Crystalline Complex may indicate a fossil paired metamorphic belt in the Central European Variscides.     

Infiltration at the Tai rain forest (Ivory Coast): Measurements and modelling

Infiltration experiments have been performed at three sites along a well-known catena under virgin tropical rain forest using a portable sprinkling infiltrometer. Experimentally determined infiltration curves are presented. Infiltration curves are also simulated on the basis of the Mein-Larson equation. The parameters for this model have been obtained from the infiltration curves (saturated conductivity) and simple soil moisture determinations (fillable porosity). The agreement between experimentally determined and modelled infiltration is reasonable, provided (a) saturated conductivity as derived from the experimental data is corrected, (b) a storage parameter, also derived from the experimental data, is added to the Mein-Larson model, and (c) the decline in soil porosity with depth is either small or occurs abruptly at shallow depth. Comparison of observed infiltration rates with rainfall intensity shows that Horton Overland Flow has to occur naturally at least on the middle and lower section of the catena. Despite the fact that most parameters can be estimated in principle from basic soil data, it remains advisable to obtain sprinkling infiltrometer field measurements, because of soil variability due to dynamic surface conditions, macroporosity, air entrapment, and irregularity of the wetting front.     

Screening of polymers on selected Hawaii soils for erosion reduction and particle settling

In recent years, high‐molecular‐weight anionic polyacrylamides (PAMs) have been tested on a variety of soils, primarily in temperate climates. However, little information is available regarding the effectiveness of PAM for preventing soil loss through runoff in tropical settings. Screening tests were performed using three negatively charged PAMs and one positively charged PAM on five Hawaii soils (two Oxisols, one Vertisol, and two Aridisols) to determine erosion loss, sediment settling, and aggregate stability. A laboratory‐scale rainfall simulator was used to apply erosive rainfall at intensities from 5 to 8·5 cm h^?1 at various PAM doses applied in both dry and solution forms. Soil detachment due to splash and runoff, as well as the runoff and percolate water volumes, were measured for initial and successive storms. The impact of PAM on particle settling and aggregate stability was also evaluated for selected soil‐treatment combinations. Among the PAMs, Superfloc A‐836 was most effective, and significantly reduced runoff and splash sediment loss for the Wahiawa Oxisol and Pakini Andisol at rates varying between 10 and 50 kg ha^?1. Reduced runoff and splash sediment loss were also noted for PAM Aerotil‐D when applied in solution form to the Wahiawa Oxisol. Significant reductions in soil loss were not noted for either the Lualualei Vertisol or the Holomua Oxisol. It is believed that the high montmorillonite content of the Lualualei Vertisol and the low cation‐exchange capacity of the Holomua Oxisol diminished the effectiveness of the various PAMs tested. The polymers were also found to enhance sediment settling of all soils and helped improve their aggregate stability. This screening study shows the potential use of PAM for tropical soils for applications such as infiltration enhancement, runoff reduction, and enhanced sedimentation of detention ponds. Copyright © 2005 John Wiley & Sons, Ltd.     

SANICLAY: simple anisotropic clay plasticity model

SANICLAY is a new simple anisotropic clay plasticity model that builds on a modification of an earlier model with an associated flow rule, in order to include simulations of softening response under undrained compression following K_o consolidation. Non‐associativity is introduced by adopting a yield surface different than the plastic potential surface. Besides, the isotropic hardening of the yield surface both surfaces evolve according to a combined distortional and rotational hardening rule, simulating the evolving anisotropy. Although built on the general premises of critical state soil mechanics, the model induces a critical state line in the void ratio–mean effective stress space, which is a function of anisotropy. To ease interpretation, the model formulation is presented firstly in the triaxial stress space and subsequently, its multiaxial generalization is developed systematically, in a form appropriate for implementation in numerical codes. The SANICLAY is shown to provide successful simulation of both undrained and drained rate‐independent behaviour of normally consolidated sensitive clays, and to a satisfactory degree of accuracy of overconsolidated clays. The new model requires merely three constants more than those of the modified Cam clay model, all of which are easily calibrated from well‐established laboratory tests following a meticulously presented procedure. Copyright © 2006 John Wiley & Sons, Ltd.     

Radon variations in a Hungarian village

 A steady radon exhalation is assumed in most publications. In a village of North-East Hungary, however, high radon concentrations have been measured, differing strongly in neighbouring houses and varying in time, due to the interplay of geochemical phenomena. Received: 20 November 1995 · Accepted: 18 June 1996     

Generating interface waves using a freely falling, instrumentedsource

In recent years, interface waves such as the Scholte wave have become important tools in the study of the geoacoustic properties of near-bottom seafloor sediments. Traditionally, these waves have been generated by explosive or pneumatic sources deployed at or near the seafloor and monitored by ocean-bottom seismographs or geophone arrays. While these sources generate the requisite interface waves, they also produce higher frequency compressional waves in the water and sediment that tend to contaminate the surface wave and make inversion of the data difficult in the near field. In this paper, a new source consisting of a freely falling projectile instrumented with an accelerometer is described. When the projectile impacts the bottom, the exact time history of the vertical force applied to the sediment is known and therefore may be convolved with the transfer function of a sediment geoacoustic model to produce accurate synthetic seismograms. Moreover, the vertical force applied to the seafloor is very efficient in generating surface wave motion while producing very little compressional wave energy so that the near-field signals are much more easily analyzed. An example of the use of the new source is presented including inversion of the received signals to obtain shear-wave velocity and attenuation as a function of depth in the near bottom sediments at a shallow-water site