Carbon dioxide degassing and thermal energy release in the Monte Amiata volcanic-geothermal area (Italy)

The quaternary volcanic complex of Mount Amiata is located in southern Tuscany (Italy) and represents the most recent manifestation of the Tuscan Magmatic Province. The region is characterised by a large thermal anomaly and by the presence of numerous CO₂-rich gas emissions and geothermal features, mainly located at the periphery of the volcanic complex. Two geothermal systems are located, at increasing depths, in the carbonate and metamorphic formations beneath the volcanic complex. The shallow volcanic aquifer is separated from the deep geothermal systems by a low permeability unit (Ligurian Unit). A measured CO₂ discharge through soils of 1.8 × 10⁹ mol a⁻¹ shows that large amounts of CO₂ move from the deep reservoir to the surface. A large range in δ¹³C_TDIC (−21.07 to +3.65) characterises the waters circulating in the aquifers of the region and the mass and isotopic balance of TDIC allows distinguishing a discharge of 0.3 × 10⁹ mol a⁻¹ of deeply sourced CO₂ in spring waters. The total natural CO₂ discharge (2.1 × 10⁹ mol a⁻¹) is slightly less than minimum CO₂ output estimated by an indirect method (2.8 × 10⁹ mol a⁻¹), but present-day release of 5.8 × 10⁹ mol a⁻¹ CO₂ from deep geothermal wells may have reduced natural CO₂ discharge. The heat transported by groundwater, computed considering the increase in temperature from the infiltration area to the discharge from springs, is of the same order of magnitude, or higher, than the regional conductive heat flow (>200 mW m⁻²) and reaches extremely high values (up to 2700 mW m⁻²) in the north-eastern part of the study area. Heat transfer occurs mainly by conductive heating in the volcanic aquifer and by uprising gas and vapor along fault zones and in those areas where low permeability cover is lacking. The comparison of CO₂ flux, heat flow and geological setting shows that near surface geology and hydrogeological setting play a central role in determining CO₂ degassing and heat transfer patterns.     

Dissociation constants of protonated cysteine species in seawater media

The dissociation constants (pK₁, pK₂ and pK₃) for cysteine have been measured in seawater as a function of temperature (5 to 45 °C) and salinity (S = 5 to 35). The seawater values were lower than the values in NaCl at the same ionic strength. In an attempt to understand these differences, we have made measurements of the constants in Na–Mg–Cl solutions at 25 °C. The measured values have been compared to those calculated from the Pitzer ionic interaction model. The lower values of pK₃ in the Na–Mg–Cl solutions have been attributed to the formation of Mg²⁺ complexes with Cys²⁻ anions

Mg²⁺ + Cys²⁻ = MgCys

The stability constants have been fitted to

after corrections are made for the interaction of Mg²⁺ with H⁺.The pK₁ seawater measurements indicate that H₃Cys⁺ interacts with SO₄²⁻. The Pitzer parameters β⁰(H₃CysSO₄), β¹(H₃CysSO₄) and C(H₃CysSO₄) have been determined for this interaction. The formation of CaCys as well as MgCys are needed to account for the values of pK₂ and pK₃ in seawater.The consideration of the formation of MgCys and CaCys in seawater yields model calculated values of pK₁, pK₂ and pK₃ that agree with the measured values to within the experimental error of the measurements. This study shows that it is important to consider all of the ionic interactions in natural waters when examining the dissociation of organic acids.     

A focal plane detector design for a wide-band Laue-lens telescope

The energy range above 60 keV is important for the study of many open problems in high energy astrophysics such as the role of Inverse Compton with respect to synchrotron or thermal processes in GRBs, non thermal mechanisms in SNR, the study of the high energy cut-offs in AGN spectra, and the detection of nuclear and annihilation lines. Recently the development of high energy Laue lenses with broad energy bandpasses from 60 to 600keV have been proposed for a Hard X ray focusing Telescope (HAXTEL) in order to study the X-ray continuum of celestial sources. The required focal plane detector should have high detection efficiency over the entire operative range, a spatial resolution of about 1mm, an energy resolution of a few keV at 500keV and a sensitivity to linear polarization. We describe a possible configuration of the focal plane detector based on several CdTe/CZT pixelated layers stacked together to achieve the required detection efficiency at high energy. Each layer can operate both as a separate position sensitive detector and polarimeter or work with other layers to increase the overall photopeak efficiency. Each layer has a hexagonal shape in order to minimize the detector surface required to cover the lens field of view. The pixels would have the same geometry so as to provide the best coupling with the lens point spread function and to increase the symmetry for polarimetric studies.     

Modeling the effects of the variability of temperature-related dynamic viscosity on the thermal-affected zone of groundwater heat-pump systems

Thermal perturbation in the subsurface produced in an open-loop groundwater heat pump (GWHP) plant is a complex transport phenomenon affected by several factors, including the exploited aquifer’s hydrogeological and thermal characteristics, well construction features, and the temporal dynamics of the plant’s groundwater abstraction and reinjection system. Hydraulic conductivity has a major influence on heat transport because plume propagation, which occurs primarily through advection, tends to degrade following conductive heat transport and convection within moving water. Hydraulic conductivity is, in turn, influenced by water reinjection because the dynamic viscosity of groundwater varies with temperature. This paper reports on a computational analysis conducted using FEFLOW software to quantify how the thermal-affected zone (TAZ) is influenced by the variation in dynamic viscosity due to reinjected groundwater in a well-doublet scheme. The modeling results demonstrate non-negligible groundwater dynamic-viscosity variation that affects thermal plume propagation in the aquifer. This influence on TAZ calculation was enhanced for aquifers with high intrinsic permeability and/or substantial temperature differences between abstracted and post-heat-pump-reinjected groundwater.

     

Assessing the Vibrational Frequencies of the Holweide Hospital in the City of Cologne (Germany) by Means of Ambient Seismic Noise Analysis and FE modelling

Ambient seismic noise measurements were conducted inside the Holweide Hospital (Cologne) for checking whether its frequencies of vibration fall into the range where soil amplification is expected. If this is the case, damage might increase in case of an earthquake due to an amplified structural response of the building. Two different techniques were used: the ratio between the horizontal and vertical components of the spectra recorded at stations located inside the building and the ratio between the corresponding components of the spectra recorded simultaneously inside the building and at a reference station placed outside. While the former method might be preferred because of less equipment involved, the latter has the advantage of producing more stable results and deleting automatically the influence of the sedimentary cover, which might obscure some eigenfrequencies of vibration of the building. An independently performed finite-element analysis of the hospital showed a good correlation between measured and calculated eigenmodes.     

Introspection on improper seismic retrofit of Basilica Santa Maria di Collemaggio after 2009 Italian earthquake

The 2009 L’Aquila, Italy earthquake highlighted the seismic vulnerability of historic masonry building structures due to improper "strengthening" retrofit work that has been done in the last 50 years. Italian seismic standards recommend the use of traditional reinforcement techniques such as replacing the original wooden roof structure with new reinforced concrete (RC) or steel elements, inserting RC tie-beams in the masonry and new RC floors, and using RC jacketing on the shear walls. The L’Aquila earthquake revealed the numerous limitations of these interventions, because they led to increased seismic forces (due to greater additional weight) and to deformation incompatibilities of the incorporated elements with the existing masonry walls. This paper provides a discussion of technical issues pertaining to the seismic retrofit of the Santa Maria di Collemaggio Basilica and in particular, the limitations of the last (2000) retrofit intervention. Considerable damage was caused to the church because of questionable actions and incorrect and improper technical choices.     

Criteria of geographic relevance: an experimental study

The relevance of geographic information has become an emerging problem in geographic information science due to an enormous increase in volumes of data at high spatial, temporal, and semantic resolution, because of ever faster rates of new data capturing. At the same time, it is not clear whether the concept of relevance developed in information science and implemented for document-based information retrieval can be directly applied to this new, highly dynamic setting. In this study, we analyze the criteria users apply when judging the relevance of geographic entities in a given mobile usage context. Two different experiments have been set up in order to gather users' opinions on a set of possible criteria, and their relevance judgements in a given scenario. The importance ascribed to the criteria in both experiments clearly implies that a new concept of relevance is required when dealing with geographic entities instead of digital documents. This new concept of ‘Geographic Relevance’ is highly dependent on personal mobility and user's activity, whose understanding may in turn be refined by the assimilation of ‘Geographic Relevance’ itself.