Recharge estimation for transient ground water modeling

Reliable ground water models require both an accurate physical representation of the system and appropriate boundary conditions. While physical attributes are generally considered static, boundary conditions, such as ground water recharge rates, can be highly variable in both space and time. A practical methodology incorporating the hydrologic model HELP3 in conjunction with a geographic information system was developed to generate a physically based and highly detailed recharge boundary condition for ground water modeling. The approach uses daily precipitation and temperature records in addition to land use/land cover and soils data. The importance of the method in transient ground water modeling is demonstrated by applying it to a MODFLOW modeling study in New Jersey. In addition to improved model calibration, the results from the study clearly indicate the importance of using a physically based and highly detailed recharge boundary condition in ground water quality modeling, where the detailed knowledge of the evolution of the ground water flowpaths is imperative. The simulated water table is within 0.5 m of the observed values using the method, while the water levels can differ by as much as 2 m using uniform recharge conditions. The results also show that the combination of temperature and precipitation plays an important role in the amount and timing of recharge in cooler climates. A sensitivity analysis further reveals that increasing the leaf area index, the evaporative zone depth, or the curve number in the model will result in decreased recharge rates over time, with the curve number having the greatest impact.     

Assessing the Vibrational Frequencies of the Cathedral of Cologne (Germany) by Means of Ambient Seismic Noise Analysis

Ambient seismic noise measurements were conducted inside the Cathedral of Cologne (Germany) for assessing its frequencies of vibration and for checking whether these occur in the range where soil amplification is expected. If this is the case, damages may increase in case of an earthquake due to an increased structural response of the building. Analysis of the ratio between the horizontal and vertical components of the spectra recorded at stations located inside the building as well as the ratio between the corresponding components of the spectra recorded simultaneously inside the building and at a reference station placed in the basement of the cathedral indicated several modes of vibration. Facilitated by these results an assessment of the seismic vulnerability was attempted for a 2D ground motion scenario using the finite element method.     

The circumnuclear X-ray reflectors in NGC 1068 and the Circinus galaxy

The ASCA and BeppoSAX spectra of the Circinus galaxy and NGC 1068 are analysed and compared with photoionization models based on cloudy . In the case of Circinus, a single, mildly ionized reflector can account for the line spectrum, while in NGC 1068 at least three different reflectors (with different ionization states) are needed. We suggest that the reflector in Circinus and the low ionized one in NGC 1068 are the inner and visible part of the material responsible for the X-ray absorption. With this assumption, we estimate for the inner radius of the absorber a value of 0.2 pc for Circinus and of a few parsecs for NGC 1068.     

Analysis of a regional change in the sign of the SAM�Ctemperature relationship in Antarctica

This study examines regional atmospheric circulation changes associated with a reversal in the sign of the relationship between the Southern Annular Mode (SAM) and near-surface temperatures at Halley station, East Antarctica, during the 1980s. We show that the key factor affecting the regional SAM?Ctemperature relationship (STR) is the relative magnitude of two climatological low pressure centres to the west and east of the area, which determines the source region of air masses advected into the locality. The principal difference affecting the STR is shown to be a trend towards a significantly weaker climatological low (higher pressure) at ~20°E during a positive phase of the SAM. Specifically, it is variations in the phase and magnitude of the wave number three patterns of atmospheric circulation, the non-annular component of the SAM, which are the principal factors governing the regional STR. A similar reversal is observed in the sign of the correlation between the SAM and oxygen-isotope values from an ice core located some 1,200?km east of Halley. This relationship is examined throughout the 20th Century, by comparing the isotope data to SAM reconstructions, and demonstrates marked decadal variability. Thus, these data suggest that switches in the STR are more likely to reflect natural variability in the long-wave patterns over the Southern Ocean rather than the influence of an anthropogenic forcing. This finding is important when considering the potential utility of Antarctic isotope data as a proxy for the SAM.     

Carbon dioxide degassing and thermal energy release in the Monte Amiata volcanic-geothermal area (Italy)

The quaternary volcanic complex of Mount Amiata is located in southern Tuscany (Italy) and represents the most recent manifestation of the Tuscan Magmatic Province. The region is characterised by a large thermal anomaly and by the presence of numerous CO₂-rich gas emissions and geothermal features, mainly located at the periphery of the volcanic complex. Two geothermal systems are located, at increasing depths, in the carbonate and metamorphic formations beneath the volcanic complex. The shallow volcanic aquifer is separated from the deep geothermal systems by a low permeability unit (Ligurian Unit). A measured CO₂ discharge through soils of 1.8 × 10⁹ mol a⁻¹ shows that large amounts of CO₂ move from the deep reservoir to the surface. A large range in δ¹³C_TDIC (−21.07 to +3.65) characterises the waters circulating in the aquifers of the region and the mass and isotopic balance of TDIC allows distinguishing a discharge of 0.3 × 10⁹ mol a⁻¹ of deeply sourced CO₂ in spring waters. The total natural CO₂ discharge (2.1 × 10⁹ mol a⁻¹) is slightly less than minimum CO₂ output estimated by an indirect method (2.8 × 10⁹ mol a⁻¹), but present-day release of 5.8 × 10⁹ mol a⁻¹ CO₂ from deep geothermal wells may have reduced natural CO₂ discharge. The heat transported by groundwater, computed considering the increase in temperature from the infiltration area to the discharge from springs, is of the same order of magnitude, or higher, than the regional conductive heat flow (>200 mW m⁻²) and reaches extremely high values (up to 2700 mW m⁻²) in the north-eastern part of the study area. Heat transfer occurs mainly by conductive heating in the volcanic aquifer and by uprising gas and vapor along fault zones and in those areas where low permeability cover is lacking. The comparison of CO₂ flux, heat flow and geological setting shows that near surface geology and hydrogeological setting play a central role in determining CO₂ degassing and heat transfer patterns.     

POLARIX: a pathfinder mission of X-ray polarimetry

Since the birth of X-ray astronomy, spectral, spatial and timing observation improved dramatically, procuring a wealth of information on the majority of the classes of the celestial sources. Polarimetry, instead, remained basically unprobed. X-ray polarimetry promises to provide additional information procuring two new observable quantities, the degree and the angle of polarization. Polarization from celestial X-ray sources may derive from emission mechanisms themselves such as cyclotron, synchrotron and non-thermal bremsstrahlung, from scattering in aspheric accreting plasmas, such as disks, blobs and columns and from the presence of extreme magnetic field by means of vacuum polarization and birefringence. Matter in strong gravity fields and Quantum Gravity effects can be studied by X-ray polarimetry, too. POLARIX is a mission dedicated to X-ray polarimetry. It exploits the polarimetric response of a Gas Pixel Detector, combined with position sensitivity, that, at the focus of a telescope, results in a huge increase of sensitivity. The heart of the detector is an Application-Specific Integrated Circuit (ASIC) chip with 105,600 pixels each one containing a full complete electronic chain to image the track produced by the photoelectron. Three Gas Pixel Detectors are coupled with three X-ray optics which are the heritage of JET-X mission. A filter wheel hosting calibration sources unpolarized and polarized is dedicated to each detector for periodic on-ground and in-flight calibration. POLARIX will measure time resolved X-ray polarization with an angular resolution of about 20 arcsec in a field of view of 15 × 15 arcmin and with an energy resolution of 20% at 6 keV. The Minimum Detectable Polarization is 12% for a source having a flux of 1 mCrab and 10⁵ s of observing time. The satellite will be placed in an equatorial orbit of 505 km of altitude by a Vega launcher. The telemetry down-link station will be Malindi. The pointing of POLARIX satellite will be gyroless and it will perform a double pointing during the earth occultation of one source, so maximizing the scientific return. POLARIX data are for 75% open to the community while 25% + SVP (Science Verification Phase, 1 month of operation) is dedicated to a core program activity open to the contribution of associated scientists. The planned duration of the mission is one year plus three months of commissioning and SVP, suitable to perform most of the basic science within the reach of this instrument. A nice to have idea is to use the same existing mandrels to build two additional telescopes of iridium with carbon coating plus two more detectors. The effective area in this case would be almost doubled.     

Monitoring and modelling of pore water pressure changes and riverbank stability during flow events

Pore water pressures (positive and negative) were monitored for four years (1996–1999) using a series of tensiometer‐piezometers at increasing depths in a riverbank of the Sieve River, Tuscany (central Italy), with the overall objective of investigating pore pressure changes in response to ?ow events and their effects on bank stability. The saturated/unsaturated ?ow was modelled using a ?nite element seepage analysis, for the main ?ow events occurring during the four‐year monitoring period. Modelling results were validated by comparing measured with computed pore water pressure values for a series of representative events. Riverbank stability analysis was conducted by applying the limit equilibrium method (Morgenstern‐Price), using pore water pressure distributions obtained by the seepage analysis. The simulation of the 14 December 1996 event, during which a bank failure occurred, is reported in detail to illustrate the relations between the water table and river stage during the various phases of the hydrograph and their effects on bank stability. The simulation, according to monitored data, shows that the failure occurred three hours after the peak stage, during the inversion of ?ow (from the bank towards the river). A relatively limited development of positive pore pressures, reducing the effective stress and annulling the shear strength term due to the matric suction, and the sudden loss of the con?ning pressure of the river during the initial drawdown were responsible for triggering the mass failure. Results deriving from the seepage and stability analysis of nine selected ?ow events were then used to investigate the role of the ?ow event characteristics (in terms of peak stages and hydrograph characteristics) and of changes in bank geometry. Besides the peak river stage, which mainly controls the occurrence of conditions of instability, an important role is played by the hydrograph characteristics, in particular by the presence of one or more minor peaks in the river stage preceding the main one. Copyright © 2004 John Wiley & Sons, Ltd.