Characterizing site response in the Attock Basin,Pakistan, using microtremor measurement analysis

The Attock Basin is situated close to the northwest of Pakistan. Recent seismic event of October 2015 (7.5M_w) near the Pakistan Afghanistan border has proved that the area of interest is seismically active and triggered a series of aftershocks of magnitude even greater than 6.5M_w. This seismic activity has posed danger to the future of the people and infrastructure especially to the northwestern part of the country. Therefore, site response analysis is essential for estimating local site conditions in response to seismic events. Ambient noise recordings were made at 50 sites within urban and semi-urban settlements in the Attock Basin to analyze the site response of the small but densely populated basin. At each of these sites, the fundamental frequency of the soft sediments (f ₀), the amplitude (A ₀) of corresponding H/V spectral ratios, the thickness of soft sediment (H) lying over competent lithology, and the soil vulnerability index (K _g) were studied. Results were correlated with sparsely available borehole data to enhance the credibility of the study conducted for microzonation and predicting the site response to earthquake seismicity in the Attock Basin. The soil vulnerability index was found to range from moderate to high. Results clearly showed that the study area exhibits low to moderate fundamental frequency with greater soft sediment thicknesses distributed throughout the study area. Moreover, higher impedance contrasts were found at most of the sites within the central part of the Attock Basin, thus reflecting a moderate to high susceptibility of damage in those regions in response to seismic events.     

Investigation of the Kumdanlı and surrounding faults on the Eğirdir Lake by conducting ground penetrating radar (GPR) profiles

A ground penetrating radar (GPR) survey was performed on the E?irdir Lake to obtain the structural properties of Kumdanl? and surrounding faults. GPR data was collected along ten profiles in various directions by using 100–200-MHz GPR antennas. The radar sections showed that the Kumdanl? Fault, SW-NE in direction, and also some other neighboring NW-SE normal faults have played an active role in forming the E?irdir-Hoyran Lakes. The deformation and the geometry obtained from the results show that the Kumdanl? Fault is a sinistral strike-slip fault including oblique and segmented displacements. The other faults (Kemerdam? and Akkeçili) have mainly normal fault systems. Their trends are generally NW-SE in direction. It is also observed that they are younger than the Kumdanl? Fault system. These fault properties demonstrate the E?irdir Lake side has an extensional structure trending SW-NE.     

Wrench tectonics of Abu Gharadig Basin,Western Desert,Egypt: a structural analysis for hydrocarbon prospects

Mapping based on the interpreted seismic data covering the Abu Gharadig Basin in the northern Western Desert has revealed that the deposition of the Upper Cretaceous succession was controlled by dextral wrench tectonics. This dextral shear accompanied NW movement of the African Plate relative to Laurasian Plate. Structural depth maps of the Cenomanian Bahariya Formation and the Turonian-Coniacian D and A members of Abu Roash Formation display a clear NE-SW anticline dissected by NW-SE normal faults. This anticline represents one of the en echelon folds characterizing the wrench compressional component. The interpreted normal faults reflect the extensional T-fractures associated with the wrenching tectonics. The interaction between the aforementioned NE-SW anticline with the NW-SE extensional faults further confirms the effect of the Upper Cretaceous dextral wrench tectonic. However, the influence of this wrench tectonics was gradually diminishing from the Cenomanian up to the Coniacian times. The NW-SE compressional stress of the dextral wrench compressional component during the Cenomanian up to Coniacian age was greater in NW direction than the SE direction. Three mapped structural closures which are predicted to be potential hydrocarbon traps belonging to the Bahariya Formation and Abu Roash D Member, and are recommended to be drilled in the study area, with potential reservoirs. The regularity of the en echelon array of both anticlines and normal faults within the wrench zones suggests additional closures may be located elsewhere beside the study area.     

New equations for predicting the field penetration index of tunnel boring machines in fractured rock mass

The Queens Water Tunnel No. 3, stage 2 having 7.5-km length and 7-m diameter, is excavated by a high-power tunnel boring machine (TBM) underneath Brooklyn and Queens area for distributing freshwater throughout the New York City, USA. This paper offers a review of the project by considering the TBM performance and rock mass interaction. Using the individual cutter force, intact, and mass rock properties, TBM performance by means of field penetration index (FPI) was predicted and compared with actual results obtained in the field. Further, the study involves statistical analysis of the laboratory and field data including machine, intact, and mass rock properties to develop new empirical equations to estimate FPI. It is stated that the FPI, also converted to the rate of penetration, could be estimated utilizing intact and mass rock properties together with cutter force for similar type of rocks with correlation coefficient of 0.88.     

Tunisian landfill leachate treatment using <Emphasis Type="Italic">Chlorella</Emphasis> sp.: effective factors and microalgae strain performance

The potential of the autoclaved Tunisian landfill leachate treatment using microalgae (Chlorella sp.) cultivation was investigated in this study. Landfill leachate was collected from Borj Chakir landfill, Tunisia. A full factorial experimental design 2² was proposed to study the effects of the incubation time and leachate ratio factors on the organic matter removal expressed in chemical oxygen demand (COD) and ammoniacal nitrogen (NH₄─N) and on the biological response of Chlorella sp. expressed by the cell density and chlorophyll content. All experiments were batch runs at ambient temperature (25 ± 2 °C). The Chlorella sp. biomass and chlorophyll a concentrations of 1.2 and 5.32 mg L^?1, respectively, were obtained with 10% leachate spike ratio. The obtained results showed that up to 90% of the ammoniacal nitrogen in landfill leachate was removed in 10% leachate ratio spiked medium with a residual concentration of 40 mg L^?1. The maximum COD removal rate reached 60% within 13 days of incubation time indicating that microalgae consortium was quite effective for treating landfill leachate organic contaminants. Furthermore, with the 10% leachate ratio spiked medium, the maximum lipid productivity was 4.74 mg L^?1 d^?1. The present study provides valuable information for potential adaptation of microalgae culture and its contribution for the treatment of Tunisian landfill leachate.     

Composition,radioactivity, and possible applications of kaolin deposits of Sinai,Egypt

This work discusses the composition, radioactivity, and possible utilization of the kaolin resources in Sinai which are hosted in thick sandstone sequences belonging to the Carboniferous (Wadi Khaboba) and Early Cretaceous (Wadi Iseila and Abansakar) ages. The characterization of kaolin was done by microscopic and SEM examination, supported by XRD and ICP-MS analyses. The studied kaolin resources consist of kaolinite, as the main constituent, associated with subsidiary dickite and halloysite, and minor contribution of smectite and illite. The most dominant non-clay mineral is quartz, besides minor gypsum, dolomite, and hematite. Ferrugination dominates, in most cases, at the upper boundaries of the kaolin lenses, suggesting possible supergene activity. The high Al₂O₃/SiO₂ ratio for the Cretaceous kaolin (0.54, in average) specifies its better grade relative to the Carboniferous kaolin (0.43, in average). The kaolin of the middle part of lens C in Wadi Iseila contains Si/Al molecular ratio of about unity, suggesting high-grade kaolin. The Carboniferous kaolin has enriched the radionuclides: U, Th, and Ra (at disequilibrium state due to leaching of eU relative to Ra) and the REE, relative to that of the Cretaceous age. The Carboniferous kaolin is characterized by a higher contribution of HREE (zircon signature), whereas LREE seems to be more influential for the Early Cretaceous kaolin (monazite signature). In spite of the very high CIA index (93 to 99), none of the analyzed kaolin deposits displays Ce abnormality. The high radioactivity of some Carboniferous kaolin can be a serious impediment for its utilization or its exportation. The kaolin of Sinai does not satisfy the international standards for paperwork industries and refractory manufacturing, but beneficiation may overcome this challenge. However, some lenses have high-grade kaolin with a low percentage of oxides of iron, magnesium, calcium, sodium, and potassium and a low radioactivity, hence nominated for the local refractory industry. The high-grade kaolin of Sinai fulfills the standards required for ceramics manufacturing in the global market. Grade 3 kaolin (< 30%, Al₂O₃) can be used in the manufacturing of white Portland cement and red glaze manufacturing on both local and global markets.     

Dissolution sequestration mechanism of CO<Subscript>2</Subscript> at the Shiqianfeng saline aquifer in the Ordos Basin,northwestern China

This study focused on the target injection layers of deep saline aquifers in the Shiqianfeng Fm. in the Carbon Capture and Sequestration (CCS) Demonstration Projects in the Ordos Basin, northwestern China. The study employed a combination method of experiments and numerical simulation to investigate the dissolution mechanism and impact factors of CO₂ in these saline aquifers. The results showed (1) CO₂ solubility in different types of water chemistry were shown in ascending order: MgCl₂-type water < CaCl₂-type water < Na₂SO₄-type water < NaCl-type water < Na₂CO₃-type water < distilled water. These results were consistent with the calculated results undertaken by TOUGHREACT with about 5% margin of error. CO₂ solubility of Shiqianfeng Fm. saline was 1.05 mol/L; (2) compared with distilled water, the more complex the water’s chemical composition, the greater the increase in HCO₃ ^?concentration. While the water’s composition was relatively simple, the tested water’s HCO₃ ^?concentrations were in close accord with the calculated value undertaken by the TOUGHREACT code, and the more complex the water’s composition, the poorer the agreement was, probably due to the complex and unstable HCO₃ ^? complicating matters when in an aqueous solution system including both tested HCO₃ ^?concentration and calculated HCO₃ ^?concentration; (3) the CO₂ solubility in the saline at the temperature conditions of 55 °C and 70 °C were 1.17 and 1.02 mol/L. When compared with the calculated value of 1.20 and 1.05 mol/L, they were almost the same with only 1 and 3% margin of error; concentrations of HCO₃ ^? were 402.73 mg/L (0.007 mol/L) and 385.65 mg/L (0.006 mol/L), while the simulation results were 132.16 mg/L (0.002 mol/L) and 128.52 mg/L (0.002 mol/L). From the contrast between the tested data and the calculated data undertaken by the TOUGHREACT code, it was shown that TOUGHRACT code could better simulate the interaction between saline and CO₂ in the dissolution sequestration capacity. Therefore, TOUGHREACT code could be used for the inter-process prediction of CO₂ long-term geological storage of CO₂; (4) The Ca²⁺ concentration and SO₄ ^2?concentration in saline water had less effect on the solubility of CO₂ and HCO₃ ^?concentration. In addition, TDS and pH values of saline affected not only the solubility of CO₂, but also the conversion of CO₂ to HCO₃ ^? due to that they can affect the activity and acid-base balance. So in fact, we just need to consider that the TDS and pH values are main impact factors in the dissolution sequestration capacity of CO₂ geological sequestration in deep saline aquifers.     

Paleoenvironment of geomorphic surfaces of an alluvial fan in the eastern Isfahan,Iran, in the light of micromorphology and clay mineralogy

Alluvial fans are one of the most important landforms in geomorphological and paloenvironmental studies. The objective of this study was the application of clay mineral assemblages and micromorphological properties of the studied paleosols in the geomorphic surfaces of an alluvial fan in the eastern Isfahan as proxies for paleoenvironmental and paleoclimatic changes. Micromorphology, X-ray diffraction, and scanning electron microscopy approaches were used to study the representative pedons. The results indicated that the illuviation process in the calcareous soils of the arid regions of the eastern Isfahan was probably in response to Quaternary moist conditions. There was no significant difference between clay coating properties of the studied relict and buried paleosols. Clay mineralogical study suggested that kaolinite and illite were inherited from the parent materials, while smectite and palygorskite were formed in the soil environment. Paleoargillic horizon was characterized by smectite and calcic (especially the calcrete) horizons were dominated by palygorskite. Palygorskite was accumulated by both neoformation and illuviation processes. High clay content, high intensity of smectite peak, and activity of the illuviation process in paleoargillic horizon demonstrated the seasonality of climate (rainfall) even in the moist periods of Quaternary in Central Iran. Clay mineralogical assemblages suggested a trend of increasing environmental aridity in the study area. This study, therefore, highlighted the role of clay mineralogical investigations in arid lands’ geomorphological and paleoenvironmental researches.     

Application of a 3D photorealistic model for the geological analysis of the Permian carbonates (Khuff Formation) in Saudi Arabia

Three dimensional (3D) photorealistic models of geological outcrops have the potential to enhance the teaching of earth sciences by providing scale models in a virtual reality environment. These models can be run on low-cost desktop computers. Photorealistic models for geological outcrops are a digital illustration of outcrop photographs with either a point cloud representation or Triangular Irregular Network (TIN) mesh of the outcrop surface. The level of detail for these models is dependent on the target resolutions (physical and optical) that were used during data acquisition. In addition, the technique in which the data is rendered as a digital model affects the level of detail that can be observed by the geologists. A colored point cloud representation is suitable for large-scale features, but fine details are lost when the geologist zooms in to view the model close up. In contrast, a photorealistic model that is constructed from photographs draped onto a triangle mesh surface derived from Light Detection and Ranging (LiDAR) point clouds provides a level of detail that is restricted only by the resolution of the photographs.     

3D geomechanical modeling and estimating the compaction and subsidence of Fahlian reservoir formation (X-field in SW of Iran)

A geomechanical model can reveal the mechanical behavior of rocks and be used to manage the reservoir programs in a better mode. Fluid pressure will be reduced during hydrocarbon production from a reservoir. This reduction of pressure will increase the effective stress due to overburden sediments and will cause porous media compaction and surface subsidence. In some oil fields, the compacting reservoir can support oil and gas production. However, the phenomena can also cause the loss of wells and reduced production and also cause irreparable damage to the surface structures and affect the surrounding environment. For a detailed study of the geomechanical behavior of a hydrocarbon field, a 3D numerical model to describe the reservoir geomechanical characteristics is essential. During this study, using available data and information, a coupled fluid flow-geomechanic model of Fahlian reservoir formation in X-field in SW of Iran was constructed to estimate the amount of land subsidence. According to the prepared model, in this field, the maximum amount of the vertical stress is 110 MPa and the maximum amount of the horizontal stress is 94 MPa. At last, this model is used for the prediction of reservoir compaction and subsidence of the surface. The maximum value of estimated ground subsidence in the study equals to 29 mm. It is considered that according to the obtained values of horizontal and vertical movement in the wall of different wells, those movements are not problematic for casing and well production and also the surrounding environment.