Sediment salt-load in the St Lucia Estuary during the severe drought of 2002–2006

The purpose of this study was to determine whether there was a sufficiently high residual salt load in the dry sediments of the St Lucia Estuary to cause salinity problems should it later fill up with either freshwater or seawater. The estuary lakes have suffered the effects of a severe drought since 2002 with the result that many areas were dry, and the salinity of the residual water varied between 4 psu and up to five times that of seawater. Measurements of the salts content in the sediments to a depth of 20 cm showed that more than 2 million tonnes of salt was held in this layer of the sediment in 2006. Recent management of the estuary (since 1970) has ensured that the mouth was not artificially opened. This was to prevent the inflow of seawater, with its salts, that would otherwise enter while the drought was in place. The results of the sediment salinity data showed that if the drought had been broken and the lake area filled with rain and river water, the resulting salinity would be about 6 psu. In March 2007, Cyclone Gamede in the Indian Ocean off the east coast of South Africa produced a wave climate at sea that resulted in the mouth breaching; thus introducing an estimated 12 million tonnes of salts. The high salinity in the system resulting from this breach is expected to have an adverse effect on the ecology of the system, whereas the residual salinity in the sediments would not have caused an environmental problem. If the estuary and lake system were to fill completely with seawater, the residual salts together with seawater will raise the salinity to an initial value higher than 40 psu, which will have the effect of suppressing much of the important submerged vegetation that is vital for sustaining juvenile fish in the system. Many of the large fauna will also suffer from a shortage of freshwater.     

Deciphering potential groundwater zone in hard rock through the application of GIS

Remote Sensing and Geographic Information System has become one of the leading tools in the field of hydrogeological science, which helps in assessing, monitoring and conserving groundwater resources. It allows manipulation and analysis of individual layer of spatial data. It is used for analysing and modelling the interrelationship between the layers. This paper mainly deals with the integrated approach of Remote Sensing and geographical information system (GIS) to delineate groundwater potential zones in hard rock terrain. The remotely sensed data at the scale of 1:50,000 and topographical information from available maps, have been used for the preparation of ground water prospective map by integrating geology, geomorphology, slope, drainage-density and lineaments map of the study area. Further, the data on yield of aquifer, as observed from existing bore wells in the area, has been used to validate the groundwater potential map. The final result depicts the favourable prospective zones in the study area and can be helpful in better planning and management of groundwater resources especially in hard rock terrains.     

Anthropogenic influence on trace element geochemistry of healing mud (peloid) from Makirina Cove (Croatia)

Due to their balneotherapeutic features, the organic-rich sediments in Makirina Cove are an important source of healing mud. An environmental geochemistry approach using normalization techniques was applied to evaluate the anthropogenic contribution of trace metals to sediments used as healing mud. Sediment geochemistry was found to be associated with land-use change and storm events, as well as with proximity of a road with heavy traffic in the summer months. Local valley topography preferentially channels lithogenic and pollutant transport to the cove. Concentrations and distribution of trace metals indicate lithogenic (Ni, Cr, Co) and anthropogenic (Pb, Cu, Zn and Se) contributions to the sediments. The calculation of enrichment factors indicates a moderate (EFs between 2–3.5) input of anthropogenic Cu and Pb in surficial sediments to a depth of 10 cm. Patients using the Makirina Cove sediments as healing mud could be to some extent exposed to enhanced uptake of metals from anthropogenic sources via dermal contact.     

Mineralogy and geochemistry of the Texeo Cu–Co mine site (NW Spain): screening tools for environmental assessment

The Cu–Co–Ni Texeo mine has been the most important source of Cu in NW Spain since Roman times and now, approximately 40,000 m³ of wastes from mine and metallurgical operations, containing average concentrations of 9,263 mg kg⁻¹ Cu, 1,100 mg kg⁻¹ As, 549 mg kg⁻¹ Co, and 840 mg kg⁻¹ Ni, remain on-site. Since the cessation of the activity, the abandoned works, facilities and waste piles have been posing a threat to the environment, derived from the release of toxic elements. In order to assess the potential environmental pollution caused by the mining operations, a sequential sampling strategy was undertaken in wastes, soil, surface and groundwater, and sediments. First, screening field tools were used to identify hotspots, before defining formal sampling strategies; so, in the areas where anomalies were detected in a first sampling stage, a second detailed sampling campaign was undertaken. Metal concentrations in the soils are highly above the local background, reaching up to 9,921 mg kg⁻¹ Cu, 1,373 mg kg⁻¹ As, 685 mg kg⁻¹ Co, and 1,040 mg kg⁻¹ Ni, among others. Copper concentrations downstream of the mine works reach values up to 1,869 μg l⁻¹ and 240 mg kg⁻¹ in surface water and stream sediments, respectively. Computer-based risk assessment for the site gives a carcinogenic risk associated with the presence of As in surface waters and soils, and a health risk for long exposures; so, trigger levels of these elements are high enough to warrant further investigation.     

Numerical modeling assessment of three-gate structures for capturing contaminated groundwater

This modeling study evaluated the capability of alternative funnel-and-gate structures with three gates for capturing contaminated groundwater in a hypothetical unconfined aquifer. Simulated interceptor structures were linear and 45 m wide, consisting of three gates and two funnels (walls). One gate occupied the center and two gates occupied the ends of the interceptor structures. The structures, positioned perpendicular to regional groundwater flow, traversed the entire thickness of the aquifer. A total of four structures were evaluated (numbers designate widths of end, center, and end gates, respectively, in meters): 3-3-3, 2-5-2, 1-7-1, and 4-1-4. Particle tracking and zonal water budgets identified shapes of capture zones and discharge patterns for each interceptor structure. A mass transport model, accounting for advection and hydrodynamic dispersion, tested the capability of each structure for capturing a contaminant plume. Results suggest that: time-dependent capture zones underestimate the amount of time to capture a contaminant plume, wide center gates facilitate plume capture, and wide end gates facilitate lateral containment of contaminants. Of the structures simulated, the 2-5-2 configuration was relatively efficient at processing and containing the simulated contaminant plume.     

Regional distribution pattern of groundwater heavy metals resulting from agricultural activities

Contaminations of groundwater by heavy metals due to agricultural activities are growing recently. The objective of this study was to evaluate and map regional patterns of heavy metals (Cd, Zn and Cu) in groundwater on a plain with high agricultural activities. The study was conducted to investigate the concentration of heavy metals and distribution in groundwater in regions of Shush Danial and Andimeshk aquifers in the southern part of Iran. Presently, groundwater is the only appropriate and widely used source of drinking water for rural and urban communities in this region. The region covers an area of 1,100 km² between the Dez and Karkhe rivers, which lead to the Persian Gulf. For this study, the region was divided into four sub-regions A, B, C and D. Additionally, 168 groundwater samples were collected from 42 water wells during the earlier months of 2004. The flame atomic absorption spectrometry (AAS-Flame) was used to measure the concentration of heavy metals in water samples and the Surfer software was used for determination of the contour map of metal distribution. The results demonstrated that in all of the samples, Cd and Zn concentrations were below the EPA MCLG and EPA secondary standard, respectively. However, the Cu contents of 4.8 % of all samples were higher than EPA MCL. It is also indicated that the concentrations of metals were more pronounced at the southern part of the studied region than at the others. The analysis of fertilizers applied for agricultural activities at this region also indicated that a great majority of the above-mentioned heavy metals were discharged into the environment. Absence of confining layers, proximity to land surface, excess agricultural activities in the southern part and groundwater flow direction that is generally from the north to the southern parts in this area make the southern region of the Shush plain especially vulnerable to pollution by heavy metals than by other contaminants.     

Landslide susceptibility and hazard mapping in Australia for land-use planning — with reference to challenges in metropolitan suburbia

This paper provides an overview of the history and current status of landslide susceptibility and hazard mapping for land-use zoning in Australia. It also describes a case study of landslide hazard mapping in a medium density, coastal, suburban residential area of metropolitan Sydney, New South Wales, Australia, with relatively steep terrain. Issues covered include identification and mapping of existing and potential landslides, and susceptibility and hazard zoning for regulatory management and land-use planning. The method involves application of the principles contained within the AGS (2000) guideline, and as updated by the AGS (2007 a,b,c,d,e) suite of guidelines.     

A practical approach to grain shape quantification

Grain shape is a key factor affecting the mechanical properties of granular materials. However, grain shape quantification techniques to distinguish one granular material from another have not reached a stage of development for inclusion in modeling the behavior of granular materials. Part of the problem is the equipment of choice for grain shape measurement is the scanning electron microscopes. This is a relatively expensive and complex device. In this paper, we investigate a practical approach using light microscopy to quantify grain shape and to identify the key shape parameters that can distinguish grains. A light microscope was found to produce grain images with sufficient quality for the purpose of observing the grain shape profile. Several grain shape parameters were determined for eight different sands. We found Circularity, Roundness, Compactness, Sphericity, Aspect Ratio and ModRatio to be the key shape parameters that differentiate these sand grains.     

Discussion on “Experimental study on fracture toughness and tensile strength of a clay” [Engineering Geology 94 (2007) 64–75]

The paper [Wang, J.-J., Zhu, J.-G., Chiu, C.F., Zhang, H., 2007. Experimental study on fracture toughness and tensile strength of a clay. Engineering Geology 94, 64–75.] focuses on two important fracture parameters of soils: tensile strength and fracture toughness. These parameters control the behaviour of soils in a wide range of situations, from the design of a simple footing to much complicated fracture behaviour of clay liners or covers. The authors have done extensive laboratory work to determine these two parameters and their laborious and complicated experimental program needs praise. However, some of the points raised in their conclusions, based on the analysis and comparison with the data from the literature, need to be discussed.