黄河三角洲桩西101站潮沟地貌形态及其水动力学研究

在潮沟下游，横跨且生趣与潮沟的横断面设了５个观测站，进行了２４ｈ的水动力测量。结果表明，涨落潮流速流向不对称，在潮沟内，涨落潮流流速差别很大，涨潮流流速最大为９ｃｍ／２，而落潮流流速最大可达３８ｃｍ／ｓ。据推测，潮沟内之所以落潮流流速明显大于涨潮流流速，可能是由于潮沟与岸线斜交有关。     

牙鲆种群动态及其资源管理

本文根据1980—1986年间鱼类生物学参数测定,结合体长分布资料的模拟分析,研究黄、渤海区牙鲆种群年龄结构、死亡动态以及在不同年龄和死亡率条件下世代资源生物量变化的规律。模型分析结果表明,当F=1.0和t_c=6.0a时,单位补充量最大群体产量为1492g。由此认为,现阶段牙鲆资源利用的最佳策略是通过增殖放流,增加资源补充;同时应适当控制捕捞压力,减少渔具对幼鱼资源的破坏并增设繁殖保护区,以追求最大持续产量。     

海上平台桶形基础模型压力压贯与负压沉贯试验研究

介绍了海上平台桶形基础模型（模型桶）压力压贯和负压沉贯的试验概况,对比分析了两者贯入力的巨大差异和产生的原因,给出了模型桶压力压贯中贯入深度与压力的关系,负压没贯负压与贯入深度,抽吸泵流量,基土渗流量,桶内土塞隆起之间的关系,试验结果表明,负压沉贯可以大大降低以砂质粉土为基土的土抗力,为在胜利油田类似基土海域海上平台应用桶形基础提供了试验依据,为海上现场导管架桶形基础平台的安装就位施工和控制提供了     

梭鱼标准代谢、内源氮排泄与体重和温度的关系

在 13.5 ,18,2 1.5 ,2 4和 2 7℃ 5个温度条件下测定了梭鱼 (体重范围 1.88～ 14.0 2 g)的标准代谢率和内源氮排泄率。梭鱼标准代谢率随体重的增加而增加 ,二者的关系为幂函数关系 ;随温度的升高而增加 ,二者的关系为指数关系 ;标准代谢率与体重和温度的关系可用如下方程表示 :RS=0 .12 4 6 W0 .9954 e0 .0 84 1T(r2 =0 .92 2 0 )。梭鱼的氨氮、尿素、总氮及能量的排泄率随体重和温度的增加而增加 ,与体重为幂函数关系 ,与温度的关系为多项式形式。梭鱼氨氮和尿素日排泄率的变幅分别为 0 .15～ 0 .88mg N/d和 0 .0 3～ 0 .2 9mg N/d。不同温度下 ,尿素排泄量占总氮比例在 9.9%～2 2 .4 9%之间 ,随温度升高该值有逐渐增大的趋势。     

青藏高原东部多年冻土退化对环境的影响

退化是本区多年冻土变化的基本趋势，不同区段退化幅度有差异，影响退化的因素除了全球气候转暖外，还有局地气候和地下水迳流。在退化敏感的地带，工程建设，牧区生态平衡都有不可忽视的影响。     

Wave-Current Forces on Small Square Cylinders (Part I)

-Based on the extended Morison Equation and model tests, the in-line forces on small square cylinders caused by waves (regular and irregular) and currents are analyzed in detail in this paper. The hydrodynamic coefficient CD and Cu related to KC number and the effect of direction of wave incidence are also given, which can be used in engineering practice.     

Elasto-Plastic Analysis of Tubular Joints of Offshore Platforms by Finite Element Method

The plastic node method is reformulated by the variational principle and is applied to elasto-plastic finite element analysis of tubular joints, eventually including the effect of internal and external gussets, stiffener rings, etc., if necessary. Four different joints are studied here in detail for the elasto-plastic behavior, the strain at the hot spot, the strain concentration factor around the intersection line, and the propagation of the plastic region with loading up to collapse in order to determine the ultimate strength, safety factor, and development of the plastic field. The present results are in good agreement with the experimental results.     

人造海洋涌升流和海洋渔场

针对渔业资源日趋减少和鱼产品需求不断增加的矛盾，探讨了建造海底山脉、人工制造海洋涌升流、从而人工制造优良海洋渔场的可行性，分析了我国建造海底山脉的水深、海底和海流条件。介绍了建造海底山脉的建筑方法和国际上建造海底山脉的最新动态。论述了我国在200n mile以内建造海底山脉的有利条件。     

贻贝(Mytilus edulis Linnaeus)唇瓣的扫描电镜观察

本文运用扫描电子显微镜技术研究了贻贝唇瓣的形态结，结果表明，贻贝唇瓣外部形态呈羽毛状，分为光滑面和皱褶面；褶皱面表面被覆浓密纤毛，分有沟嵴和无嵴两部分，界限明显，光滑面纤毛较少，呈簇状，分布不均，在褶皱面中央分界处和光滑面的一侧，有大量球状突起，为杯状细胞所在，纤毛和粘液在食物分拣和运输中起重要作用。     

Computation of Viscous Uniform and Shear Flow over A Circular Cylinder by A Finite Element Method

The incompressible viscous uniform and shear flow past a circular cylinder is studied. The two-dimensional Navier-Stokes equations are solved by a finite element method. The governing equations are discretized by a weighted residual method in space. The stable three-step scheme is applied to the momentum equations in the time integration. The numerical model is firstly applied to the computation of the lid-driven cavity flow for its validation. The computed results agree well with the measured data and other numerical results. Then, it is used to simulate the viscous uniform and shear flow over a circular cylinder for Reynolds numbers from lO0 to lO00. The transient time interval before the vortex shedding occurs is shortened considerably by introduction of artificial perturbation. The computed Strouhal number, drag and lift coefficients agree well with the experimental data. The computation shows that the finite element model can be successfully applied to the viscous flow problem.