Influence of instruments on the H/V spectral ratios of ambient vibrations

For an optimal analysis of the H/V curve, it appears necessary to check the instrument signal to noise ratio in the studied frequency band, to ensure that the signal from the ground noise is well above the internal noise. We assess the reliability and accuracy of various digitizers, sensors and/or digitizer-sensor couples. Although this study is of general interest for any kind of seismological study, we emphasize the influence of equipment on H/V analysis results. To display the impact of the instrumental part on the H/V behavior, some series of tests have been carried out following a step-by-step procedure: first, the digitizers have been tested in the lab (sensitivity, internal noise...), then the three components sensors, still in the lab, and finally the usual user digitizers-sensors couple in lab and outdoors. In general, the digitizer characteristics, verified during this test, correspond well to the manufacturer specifications, however, depending on the digitizer, the quality of the digitized waveform can be very good to very poor, with variation from a channel to another channel (gain, time difference etc.). It appears very clearly that digitizers need a warming up time before the recording to avoid problems in the low-frequency range. Regarding the sensors, we recommend strongly to avoid the use of “classical” accelerometers (i.e., usual force balance technology). The majority of tested seismometers (broadband and short period, even 4.5 Hz) can be used without problems from 0.4 to 25 Hz. In all cases, the instrumentation should be checked first to verify that it works well for the defined study aim, but also to define its limit of use (frequency, sensitivity...).     

Formation of U-depleted rhyolite from a basanite at El Hierro, Canary Islands

Phonolite and trachyte are the felsic magmas of the alkaline magma suites, which characterize the Canary Islands. The October 2011 submarine eruption off El Hierro, the westernmost island, nevertheless, produced a small volume of rhyolitic magma. The rhyolite occurred as highly vesicular, white coloured pumices enveloped in and mingled with darker coloured basanitic pumice. The basanitic pumice is relatively crystal poor with a few euhedral olivines (mostly Fo_77–79), clinopyroxenes and Fe-rich spinels, whereas very rare olivine of same composition is found together with equally rare Fe-sulphide and FeTi-rich oxides in the rhyolite. The Fe–Mg exchange equilibrium in the oxides permits to calculate an equilibrium temperature of 970–890 °C for the rhyolite, in agreement with quartz-melt equilibrium at ca. 930 °C. A striking mineralogical feature of the rhyolite is the presence of rounded to contorted grains of milky quartz, which are xenocrysts incorporated and partly dissolved into the magma. Analyses of residual volatile concentrations in the glasses show that the rhyolite melt was highly degassed, whereas the basanitic glass still has important halogen concentrations. Trace element patterns of the mafic glasses and their elevated incompatible element concentrations are typical of the western Canary Island basanites. In contrast, the trace element composition of the rhyolite shows surprisingly low concentrations for all elements except the most incompatible ones (e.g. Rb, Ba, K and Th). All other measured LILE, HFSE and REE have significantly lower concentration than the basanitic counterpart that can be explained by fractionation of accessory phases (1 % apatite, 1 % sphene and 0.1 % zircon). Surprisingly, low U concentration is presumably related to elevated oxygen fugacity in the rhyolite, causing U to be in a hexavalent state, and fluxing of F-rich gas leading to volatilization of UF₆, known to emanate at low temperature. The results suggest that a gas-rich basanitic melt remobilized a small volume of stagnant rhyolitic melt formed by incorporation of approximately 10 % quartz-rich sediment into a late differentiate of trachytic composition. Sediments at the interface of an old oceanic crust adjacent to a continental shield and younger volcanic island are likely to act as magma traps were sediment assimilation may alter the mantle-derived magma composition. Quartz assimilation thus explains the production of rhyolite magma in a volcanic island characterized by an alkaline magma series from primitive basanites to trachytes.     

Quaternary geochemical evolution of the salars of Uyuni and Coipasa, Central Altiplano, Bolivia

The central trough of the Bolivian Altiplano is occupied by two wide salt crusts: the salar of Uyuni, which is probably the largest salt pan in the world (10,000 km²) and the salar of Coipasa (2,500 km²). Both crusts are essentially made of porous halite filled with an interstitial brine very rich in Li, K, Mg, B (up to 4.7 g/l Li, 4.3 g/l B, 30 g/l K and 75 g/l Mg). Lithium reserves are the highest known in the world, around 9 × 10⁶ tons. Potassium, magnesium and boron reserves in brines are also important (around 194 × 10⁶ tons K, 8 × 10⁶ tons B and 211 × 10⁶ tons Mg).

The crusts are the remnant of saline Lake Tauca (13,000–10,000 yr BP). Its salinity was estimated approximately at 80 g/l. Its paleochemistry was derived in two ways: (1) by dissolving the present amounts of all chemical components in the former lake volume, and (2) by simulating the evaporation of the major inflows to the basin. The resulting chemical compositions are quite different. The dissolution-derived one is 5 to 50 times less concentrated in Li, K, Mg, B than the evaporation-simulated ones. However all compositions present the same Na and Cl contents. This suggests either a removal of bittern salts or an enrichment of the former lake water in Na and Cl.

The most probable interpretation is that Lake Tauca redissolved a salt crust akin to that existing today. Several older lakes have been detected on the Altiplano. Nevertheless, such an explanation only pushes the problem back. It is likely that the anomaly was transferred from one lake to an other. Three hypotheses may be put forward: (1) bittern seepage through bottom sediments, (2) uptake of the missing components by minerals, and (3) leaching of ancient evaporites from the catchment area at the beginning of the lacustrine history of the basin. The excess halite could have been recycled from lake to lake. This latter process seems to be the most effective to explain the large excess of Na and Cl over the bittern solutes — Li, K, Mg and B. The occurrence of almost pure Na/1bCl saline springs flowing out from a gypsum diapir in the northern Altiplano gives substantial support to this hypothesis.     

An application of Iatroscan thin-layer chromatography with flame ionization detection—lipid classes of microorganisms as biomarkers in the marine environment

Iatroscan TLC-FID combines the separatory capabilities of thin-layer chromatography (TLC) (on silica coated chromarods) with the possibility of quantitation by flame ionization detection (FID). It can be used to separate lipid extracts into classes of compounds ranging from neutral to polar products. The rapidity with which this system provides lipid class profiles from small samples makes it particularly useful in oceanographic studies where routine analyses of large numbers of samples are required. Lipid classes were analysed in 4 marine bacterial strains grown on various substrates and 10 microalgae isolated from the marine environment and grown in batch cultures. Data on lipid composition of these microorganisms were obtained and compared to literature data. Results show that ratios between classes of compounds within the different groups of microorganisms were characteristic enough to constitute a good print of bacterial or phytoplankton sources in organic matter in sea water. In a preliminary study, phospholipid classes from a bacterial strain and a microalga were separated. Results show that the determination of ratios between phospholipid classes in organic matter could represent an improvement in the utilization of lipid classes as biomarkers.     

Correlations among the reflectances of vitrinite, chitinozoans, graptolites and scolecodonts

Paleozoic marine sequences sampled in outcrops and wells of northeastern Gaspe Peninsula (Quebec Appalachians) yield kerogen composed in part of vitrinite and zooclasts (chitinozoans, scolecodonts and graptolites) on which reflectance measurements were made.The comparison between means of random measurements show that reflectance of chitinozoans is similar to that of telinite (vitrinite with a cellular texture) and that the reflectance of scolecodonts is significantly lower than that of telinite in the lower range of studied values. At higher reflectivities differences decrease but, at the end of the condensate gas zone reflectancea are not yet identical. As shown by previous studies, reflectance of graptolites is slightly less than that of telinite.Pyrobitumen reflectance is related to the lithology of the host-rock and no generalized correlation can be established between the reflectance of pyrobitumen and that of vitrinite.     

Assessment of wind-forcing impact on a global wind-wave model using the TOPEX altimeter

The study presents assessment of an operational wave model (Wavewatch III), focusing upon the model sensitivity to wind-forcing products. Four wind fields are used to drive the model, including the NCEP/NCAR reanalysis and three other products that assimilate various satellite wind measurements having high spatial resolution, including the QuikSCAT scatterometer. Three wave field statistics: significant wave height, mean zero-crossing wave period, and mean square slope are compared with collocated TOPEX altimeter derivatives to gauge the relative skill of differing wind-forced model runs, as well as to demonstrate an extended use of the altimeter beyond simply supplying wave height for wave model validation and assimilation. Results suggest that model output is critically sensitive to choice of the wind field product. Higher spatial resolution in the wind fields does lead to improved agreement for the higher-order wave statistics.