Unified approach to amplitude attenuation and coda excitation in the randomly inhomogeneous lithosphere

A unified model is proposed for explaining the frequency dependent amplitude attenuation and the coda wave excitation on the basis of the single scattering process in the randomly inhomogeneous lithosphere. Adopting Birch's law and a direct proportion between density and wave velocity, we statistically describe the inhomogeneous medium by one random function characterized by the von Karman autocorrelation function. We calculate the amplitude attenuation from the solid angle integral of scattered wave energy on the basis of the Born approxiimation after subtracting the travel-time fluctuation effect caused by slowly varying velocity inhomogeneities. This subtraction is equivalent to neglect energy loss by scattering within a cone around the forward direction. The random inhomogeneity of the von Karman autocorrelation function of order 0.35 with the mean square fractional fluctuation of 7.2×10^–3 1.3×10^–2 and the correlation distance of 2.15.1 km well explains observed backward scattering coefficientg and the ratioQ _P ^–1 /Q _S ^–1 , and observed and partially conjecturedQ _S ^–1 for frequencies between 0.5 Hz and 30 Hz.     

Performance of Mortar and Chemical Grout Injection into Surrounding Soil When Slurry Pipe-jacking Method is Used

Small-diameter shallow tunnels are often being built by using the slurry pipe-jacking method. This system involves the pushing or thrusting of a drivage machine and concrete pipes into the ground. Chemical grout injection into the surrounding soil around the tunnel is carried out after the drivage and pushing processes are finished. The purpose of the chemical grout injection is to maintain permanent stability of the surrounding soil. However, the behavior of the chemical grouting material in the surrounding soil around the tunnel and the amount of optimum injection is not clearly understood. From these points of view, this paper discusses the performance of the chemical grouting material, when it is injected into the surrounding soil around the tunnel, by means of 2-D Eulerian–Lagrangian seepage analysis. Moreover, the effectiveness of the chemical grout injection was evaluated by using the non-linear finite element method. This investigation show when the range of the grouted zone is designed; it is necessary that the relationship between Young’s modulus of the soil/grouted zone and the confining stress be taken into consideration in order to establish effective, economical and safe chemical grout injection system. Understanding the performance of the seepage/dispersion behavior of the chemical grout and the characteristics of soil/ grouted zone is also important.     

Process of Housing Damage Assessment: The 1995 Hanshin-Awaji Earthquake Disaster Case

Rebuilding of victims' livelihoods was a crucial issue in the restoration process in the1995 Hanshin-Awaji Earthquake Disaster. Housing damage assessment influencedmost of the rebuilding of the livelihood in the long term, because the Victim Certificatesissued by the local governments based on the results of the Housing damage assessmentwas required to receive most of the individual assistance measures. In the process ofHousing damage assessment, many complex problems arose, leading to extensivework on the part of the disaster responders. Consequently, a considerable number ofvictims were dissatisfied with the assessment and applied for a resurvey. Due to a floodof requests for resurvey, disaster responders had to work on damage assessment, leavingrelief activities aside.In order to facilitate Housing damage assessment, this paper discusses thefollowing five points: (1) the processes and the problems of assessments performedin the Hanshin-Awaji Earthquake Disaster, (2) the changes in the nature of informationneeded by the victims, (3) the improvements over the present damage assessment, (4)the housing situation in Japan, and (5) the international situation on damage assessment.It is obvious from the results that a poor damage assessment system and the size ofthe disaster produced a very large work load. Differences in appreciation among theinvestigators also contributed to unfair assessments and led to the victims beingincreasingly dissatisfied by the survey results. Finally, a design concept for acomprehensive damage assessment system, which has been derived from theabove five points, is proposed for post-disaster management.     

Interactive behavior of soil–pile-superstructure system in transient state to liquefaction by means of large shake table tests

Shaking table tests were conducted by means of a large-scale laminar box with 4 m in length, 2 m in width and 2 m in height in order to investigate behavior of a soil-pile-superstructure system in liquefiable ground. A model two-storey structure, supported by a pile group, was set in a saturated sand deposit, and subjected to a sinusoidal base motion with increasing amplitude. Discussions are focused on the transient behavior until soil liquefaction occurs. Main interests are characteristics of springs used in a sway-rocking model and a multi-freedom lumped mass (MFLM) model that are frequently used in soil–pile interaction analysis. The spring constant in the sway-rocking model is represented by restoring force characteristics at the pile head, and that in the MFLM system is represented by an interaction spring connecting the pile to the free field. The transient state prior to soil liquefaction is shown to be important in the design of a pile because dynamic earth pressure shows peak response in this state. The reduction of the stiffness due to excess porewater generation and strain dependent nonlinear behavior is evaluated.     

Strain field measurements of rubber by image analysis and design criteria for laminated rubber bearings (LRB)

Although seismic isolation rubber bearings in bridges and buildings have proven to be a very effective passive method for reducing earthquake‐induced forces, a detailed mechanical modeling of the rubber that is used in bearings under large strains has not been established. Therefore, a 3D model of failure behavior and the design criteria for the safety evaluation of seismic isolation bearings have not yet been developed. This paper presents: (1) correlation‐based template‐matching algorithms to measure large strain fields of continua; (2) a failure criterion for rubber; and (3) the design criteria for the safety evaluation of laminated algorithms, data‐validation algorithms were developed and implemented to eliminate possible unrealistic displacement vectors present in the measured displacement field. The algorithms were successfully employed in the strain field measurement of LRB and rubber materials that are subjected to failure. The measured local strains for rubber material at failure were used to develop a failure criterion for rubber. The validity of the proposed criterion was evaluated by applying it to the LRB; the criterion was introduced into a 3D finite element model of LRB, compared with the experimental results of bearings failure, and verified. Finally, design criteria are proposed for LRB for the safety evaluation. Copyright © 2003 John Wiley & Sons, Ltd.