Changes in the circulation of Tampa Bay due to Hurricane Frances as recorded by ADCP measurements and reproduced with a numerical Ocean model

Hurricane Frances is shown to greatly alter the hydrodynamics within Tampa Bay, Florida, and the exchange of water with the Gulf of Mexico in both observational data and a realistic numerical circulation model of the Tampa Bay estuary. Hurricane Frances hit Tampa Bay on September 5, 2004 with surface winds peaking twice near 22 m s⁻¹. There were three stages to the hydrodynamic effect of Frances on Tampa Bay. The first stage included the approach of Frances up to the first wind peak. The winds were to the south and southeast. During this stage sea level was maintained below mean sea level (MSL) and the residual current (demeaned, detided) was weak. The second stage began as the winds turned to the east and northeast, as the eye passed near the bay, and ended as the second wind peak appeared. During this stage the residual currents were strongly positive (into the bay), raising sea level to 1.2 m above MSL at St. Petersburg. The measured residual circulation peaked at over +0.7 m s⁻¹ near the surface. The model shows this velocity peak yielded a maximum volume flux into the bay of +44,227 m³ s⁻¹, displacing a total volume of 1.5 billion m³ in just a few hours, about 42% of the bay volume. In the third stage a strong negative flow developed as the wind and sea level relaxed to near normal levels. The ADCP measured a peak outflow of −0.8 m s⁻¹ during this time. Model results indicate a maximum flux of −37,575 m³ s⁻¹, and that it took about 50 h to drain the extra volume driven into the bay by Hurricane Frances.     

The effect of multiple stressors on salt marsh end-of-season biomass

It is becoming more apparent that commonly used statistical methods (e.g. analysis of variance and regression) are not the best methods for estimating limiting relationships or stressor effects. A major challenge of estimating the effects associated with a measured subset of limiting factors is to account for the effects of unmeasured factors in an ecologically realistic matter. We used quantile regression to elucidate multiple stressor effects on end-of-season biomass data from two salt marsh sites in coastal Louisiana collected for 18 yr. Stressor effects evaluated based on available data were flooding, salinity air temperature, cloud cover, precipitation deficit, grazing by muskrat, and surface water nitrogen and phosphorus. Precipitation deficit combined with surface water nitrogen provided the best two-parameter model to explain variation in the peak biomass with different slopes and intercepts for the two study sites. Precipitation deficit, cloud cover, and temperature were significantly correlated with each other. Surface water nitrogen was significantly correlated with surface water phosphorus and muskrat density. The site with the larger duration of flooding showed reduced peak biomass, when cloud cover and surface water nitrogen were optimal. Variation in the relatively low salinity occurring in our study area did not explain any of the variation inSpartina alterniflora biomass.     

Carbonates calibrated against oceanographic parameters along a latitudinal transect in the Gulf of California, Mexico

Trophic resources are an important control governing carbonate production. Though this importance has long been recognized, no calibration exists to quantitatively compare biogenic assemblages within trophic resource fields. This study presents a field calibration of carbonate producers in a range of settings against high‐resolution in situ measurements of nutrients, temperature and salinity. With its latitudinal extent from 30° to 23° N, the Gulf of California, Mexico, spans the warm‐temperate realm and encompasses nutrient regimes from oligo‐mesotrophic in the south to eutrophic in the north. Accordingly, from south to north carbonates are characterized by: (i) coral‐dominated shallow carbonate factories (5–20 m water depth) with average sea‐surface temperatures of 25 °C (min. 18 °C, max. 31 °C), average salinities of 35·06‰ and average chlorophyll a levels, which are a proxy for nutrients, of 0·25 mg Chl a m^?3 (max. 0·48, min. 0·1). (ii) Red algal‐dominated subtidal to inner‐shelf carbonate formation (10–25 m) in the central Gulf of California exhibiting average temperatures of 23 °C (min. 18 °C, max. 30 °C), average salinities of 35·25‰, and average Chl a levels of 0·71 Chl a m^?3 (max. 5·62, min. 0). (iii) Molluskan bryozoan‐rich inner to outer shelf factories in the northern Gulf of California (20–50 m) with average sea surface temperatures of only 20 °C (min. 13 °C, max 29 °C), average salinities of 35·01‰, and average contents of 2·2 mg Chl a m^?3 (max. 8·38, min. 0). By calibrating sedimentological data with in situ measured oceanographic information in different environments, the response of carbonate producers to environmental parameters was established and extrapolated to carbonates on a global scale. The results demonstrate the importance of recognizing and quantifying trophic resources as a dominant control determining the biogenic composition and facies character of both modern and fossil carbonates.     

The sequence of sediment behaviour during wave-induced liquefaction

This paper presents the results of an experimental investigation of the complete sequence of sediment behaviour beneath progressive waves. The sediment was silty with d ₅₀ = 0.060 mm. Two kinds of measurements were carried out: pore-water pressure measurements (across the sediment depth), and water-surface elevation measurements. The process of liquefaction/compaction was videotaped from the side simultaneously with the pressure and water-surface elevation measurements. The video records were then analysed to measure: (i) the time development of the mudline, (ii) the time development of liquefaction and compaction fronts in the sediment and (iii) the characteristics of the orbital motion of the liquefied sediment including the motion of the interface between the water body and the sediment. The ranges of the various quantities in the tests were: wave height, H  = 9–17 cm, wave period, T  = 1.6 sec, water depth = 42 cm, and the Shields parameter = 0.34–0.59. The experiments reveal that, with the introduction of waves, excess pore pressure builds up, which is followed by liquefaction during which internal waves are experienced at the interface of the water body and the liquefied sediment, the sequence of processes known from a previous investigation. This sequence of processes is followed by dissipation of the accumulated excess pore pressure and compaction of the sediment which is followed by the formation of bed ripples. The present results regarding the dissipation and compaction appear to be in agreement with recent centrifuge wave-tank experiments. As for the final stage of the sequence of processes (formation of ripples), the ripple steepness (normalized with the angle of repose) for sediment with liquefaction history is found to be the same as that in sediment with no liquefaction history.     

A sequence stratigraphic model for an intensely bioturbated shallow-marine sandstone: the Bridport Sand Formation, Wessex Basin, UK

The Bridport Sand Formation is an intensely bioturbated sandstone that represents part of a mixed siliciclastic‐carbonate shallow‐marine depositional system. At outcrop and in subsurface cores, conventional facies analysis was combined with ichnofabric analysis to identify facies successions bounded by a hierarchy of key stratigraphic surfaces. The geometry of these surfaces and the lateral relationships between the facies successions that they bound have been constrained locally using 3D seismic data. Facies analysis suggests that the Bridport Sand Formation represents progradation of a low‐energy, siliciclastic shoreface dominated by storm‐event beds reworked by bioturbation. The shoreface sandstones form the upper part of a thick (up to 200 m), steep (2–3°), mud‐dominated slope that extends into the underlying Down Cliff Clay. Clinoform surfaces representing the shoreface‐slope system are grouped into progradational sets. Each set contains clinoform surfaces arranged in a downstepping, offlapping manner that indicates forced‐regressive progradation, which was punctuated by flooding surfaces that are expressed in core and well‐log data. In proximal locations, progradational shoreface sandstones (corresponding to a clinoform set) are truncated by conglomerate lags containing clasts of bored, reworked shoreface sandstones, which are interpreted as marking sequence boundaries. In medial locations, progradational clinoform sets are overlain across an erosion surface by thin (<5 m) bioclastic limestones that record siliciclastic‐sediment starvation during transgression. Near the basin margins, these limestones are locally thick (>10 m) and overlie conglomerate lags at sequence boundaries. Sequence boundaries are thus interpreted as being amalgamated with overlying transgressive surfaces, to form composite erosion surfaces. In distal locations, oolitic ironstones that formed under conditions of extended physical reworking overlie composite sequence boundaries and transgressive surfaces. Over most of the Wessex Basin, clinoform sets (corresponding to high‐frequency sequences) are laterally offset, thus defining a low‐frequency sequence architecture characterized by high net siliciclastic sediment input and low net accommodation. Aggradational stacking of high‐frequency sequences occurs in fault‐bounded depocentres which had higher rates of localized tectonic subsidence.     

Controls on low-pressure anatexis

Low-pressure anatexis, whereby rocks melt in place after passing through the andalusite stability field, develops under more restricted conditions than does low-pressure metamorphism. Our thermal modelling and review of published work indicate that the following mechanisms, operating alone, may induce anatexis in typical pelitic rocks without inducing wholesale melting in the lower crust: (i) magmatic advection by pervasive flow; (ii) crustal-scale detachment faulting; and (iii) the presence of a high heat-producing layer. Of these, only magmatic advection by pervasive flow and crustal-scale detachment faulting have been shown quantitatively to provide sufficient heat to cause widespread melting. Combinations of the above mechanisms with pluton-scale magmatic advection, shear heating, removal of the lithospheric mantle, or with each other provide additional means of developing suitable high temperatures at shallow crustal levels to generate low-pressure anatexis.