Otec cold water pipe design for problems caused by vortex-excited oscillations

Vortex-excited oscillations of marine structures result in reduced fatigue life, large hydrodynamic forces and induced stresses, and sometimes lead to structural damage and to destructive failures. The cold water pipe of an Ocean Thermal Energy Conversion (OTEC) plant is nominally a bluff, flexible cylinder with a large aspect ratio (L/D = length/diameter), and is likely to be susceptible to resonant vortex-excited oscillations. The objective of this paper is to survey recent results pertaining to the vortex-excited oscillations of structures in general and to consider the application of these findings to the design of the OTEC cold water pipe. Practical design calculations are given as examples throughout the various sections of the report.This paper is limited in scope to the problems of vortex shedding from bluff, flexible structures in steady currents and the resulting vortex-excited oscillations. The effects of flow non-uniformities, surface roughness of the cylinder, and inclination to the incident flow are considered in addition to the case of a smooth cylinder in a uniform stream. Emphasis is placed upon design procedures, hydrodynamic coefficients applicable in practice, and the specification of structural response parameters relevant to the OTEC cold water pipe. There are important problems associated with the shedding of vortices from cylinders in waves and from the combined action of waves and currents, but these complex fluid/structure interactions are not considered in this paper.     

Beach accretion and erosion, Burullus-Gamasa coast, Egypt

Several areas of erosion and accretion were observed along the Burullus-Gamasa beach. The accreted sands are coarser and less sorted than the eroded ones. Differentiation between them could be achieved on the basis of their grain-size fractions, shape of grain-size distribution curves and statistical grain-size parameter relationships.     

Plate boundaries and evolution of the Solomon Sea region

The Solomon Sea Plate was widely developed during late Oligocene, separating the proto-West Melanesian Arc from the proto-Trobriand Arc. Spreading in the Bismarck Sea and in the Woodlark Basin resulted from interaction between the Pacific and Australian Plates, specifically from the collision of the proto-West Melanesian Arc with north New Guinea, which occurred after arc reversal. This model explains the extensive Miocene, Pliocene, and Quaternary volcanism of the Papua New Guinea mainland as it related to southward subduction of the Trobriand Trough. Our interpreted plate motions are concordant with the geological evidence onshore and also with complex tectonic features in the Solomon Sea Basin Region.     

Microearthquakes along the back-arc spreading system in the eastern Bismarck Sea

OBS’s were deployed for 26 to 29 days in the eastern Bismarck Sea to investigate the back-arc spreading. Hypocenters of 186 shallow earthquakes were determined using P- and S-waves from at least five stations. In the western survey area, a transform fault zone is marked by a linear micro-earthquake activity striking N65°W and less than 5 km wide. The predominant type of their focal mechanisms is strike-slip. In the eastern area, several intermittent zones of micro-earthquakes and their strike-slip type focal mechanisms suggest the location of short-length transform faults separating en-echelon spreading ridges.     

Kinetic studies of the rate of dissolution of silica and diatom tests in sea water

Kinetic studies have been carried out on the dissolution of 10μm beads of silica and of the siliceous tests of two species of diatoms (Thalassiosira fluviatus andSkeletonema costatum) in sea water at 10–50°C and over the pH range 6–9. At all temperatures dissolution of the biogenous silica occurred most rapidly at pH 8 and most slowly at pH 6. First order kinetics were closely followed when the silica was present in a considerable excess over that required for saturation, the rate being proportional to the area of the silica. Apparent deviation from this type of kinetics occurred when there was insufficient silica to bring about saturation. This was undoubtedly due to the progressive decrease in the surface area which takes place as the particle dissolves. Application of the rather simplistic model developed by Kamataniet al. (1980), which makes allowance for this decrease, gave a close correspondence with the data until ∼ 90% of the silica had dissolved.     

Simplified method of deep-tow seismic profiling

To improve resolution of seismic-reflection profiles in continental slope water depths of 900 to 1500 m, a single hydrophone was towed about 150 m off the bottom to receive reflected signals from a surface-towed sparker sound source. That deep-towed hydrophone data show that valleys which appear V-shaped in records from a surface-towed hydrophone are flat-bottomed, and that subbottom reflections from an erosional unconformity can be much better resolved. The data produced by this technique are very hepful when used in conjunction with records from conventional surface-towed seismic-profiling equipment.     

On the capsize performance of a discus buoy in deep sea breakers

The mode of capsize of a discus buoy in breaking waves is discussed. The results of model tests are given; these show that a judicious choice of mooring design can substantially reduce the chance of capsize. A comparison is made with the performance of the buoy on station.