Seasonal variations in prey selection by estuarine black-headed gulls (Larus ridibundus)

The number of black-headed gulls (Larus ridibundus) in the Clyde Estuary is large. In summer the average density has reached 1350 gulls km^?2 and in winter 180 gulls km^?2. This paper compares prey selection and feeding efficiency in gulls during summer and winter on tidal flats, and considers how seasonal differences may be adaptations to cope with seasonal changes in prey availability.Gross and net rates of energy intake were highest in summer because gulls captured more of the polychaete N. diversicolor than the amphipod C. volutator. In winter, gulls selected for C. volutator and therefore an energetically less profitable diet. Throughout the year gulls selected more C. volutator relative to N. diversicolor than expected on energetic grounds and so apparently did not maximize potential net rate of energy intake.Gulls used three techniques to capture prey and made most intensive use of the ‘crouch’ technique. Crouching gulls attained a much higher net rate of energy intake than ‘upright’ or ‘paddling’ gulls.A log-linear model showed that (a) season, water depth and gull density determined feeding technique and (b) feeding technique and season independently determined foraging success and prey selection. Thus gull density and water depth acted on prey selection through imposed variations in feeding technique.Reasons for gulls selecting energetically unprofitable C. volutator and for the use of several distinct feeding techniques are discussed.     

A simple model for lensing by black holes in galactic nuclei

The lensing properties of the Plummer model with a central point mass and external shear are derived, including the image multiplicities, critical curves and caustics. This provides a simple model for a flattened galaxy with a central supermassive black hole. For the Plummer model with black hole, the maximum number of images is four, provided the black hole mass is less than an upper bound which is calculated analytically. This introduces a method to constrain black hole masses by counting images, thus applicable at cosmological distance. With shear, the maximum number of images is six and we illustrate the occurrence of an astroid caustic and two metamorphoses.     

Deep-ocean piezometer probe technology for geotechnical investigations

Two single-sensor piezometer probes, 8 mm in diameter, were developed for deep-ocean geotechnical investigations. These probes were tested in a hyperbaric chamber pressurized to 55 MPa (8000 psi). Testing was performed for a period of five weeks under high hydrostatic pressure with the probes inserted in reconstituted illitic marine sediment. Small differential pore-water pressures were generated in response to both mechanically and thermally generated forcing functions. During deep-ocean simulated pressure tests, the sensors exhibited excellent sensitivity and stability. These developments in piezometer-probe technology provide a quantitative means of assessing important geotechnical parameters of fine-grained seabed deposits.     

Generalized strain probing of constitutive models

Advanced material constitutive models are used to describe complex soil behaviour. These models are often used in the solution of boundary value problems under general loading conditions. Users and developers of constitutive models need to methodically investigate the represented soil response under a wide range of loading conditions. This paper presents a systematic procedure for probing constitutive models. A general incremental strain probe, 6D hyperspherical strain probe (HSP), is introduced to examine rate‐independent model response under all possible strain loading conditions. Two special cases of HSP, the true triaxial strain probe (TTSP) and the plane‐strain strain probe (PSSP), are used to generate 3‐D objects that represent model stress response to probing. The TTSP, PSSP and general HSP procedures are demonstrated using elasto‐plastic models. The objects resulting from the probing procedure readily highlight important model characteristics including anisotropy, yielding, hardening, softening and failure. The PSSP procedure is applied to a Neural Network (NN) based constitutive model. It shows that this probing is especially useful in understanding NN constitutive models, which do not contain explicit functions for yield surface, hardening, or anisotropy. Copyright © 2004 John Wiley & Sons, Ltd.     

Methods of array element localization for a towed underwateracoustic array

The location of the hydrophones on a towed underwater acoustic array as a function of time (array element localization) is needed for signal processing. Methods to perform this localization using least squares polynomial fitting to data from depth sensors, heading sensors, and sensors detecting a ping from a single source are discussed. Arc distance along the array is used as the independent parameter so that all solutions are constrained to be space curves. Examples of application to real data are presented, and techniques to discriminate against bad sensor data are discussed     

New developments in eclipsing binary light curve modeling

The light curve modeling of binary stars has continued to evolve since its founding by Henry Norris Russell (see Russell and Merrill 1952 and citations therein) nearly a century ago, accelerated in the 1950s by Kopal's introduction of Roche geometry into models and by the development of synthetic light curve computer code in the 1970's. Improved physics and the use of more kinds of observational input are providing another round of important advances that promise to enlarge our knowledge of both binary stars and ensembles containing them. Here we discuss the newer horizons of light curve modeling and the steps being taken toward them.     

Theoretical accuracy of synthetic aperture sonar micronavigation using a displaced phase-center antenna

The Cramer-Rao lower bounds on the cross-track translation and rotation of a displaced phase-center antenna (DPCA) in the slant range plane between two successive pings (known as DPCA sway and yaw in what follows) are computed, assuming statistically homogeneous backscatter. These bounds are validated using experimental data from a 118-182-kHz sonar, showing an accuracy of the order of 20 microns on the ping-to-ping cross-track displacements. Next, the accuracy required on the DPCA sway and yaw in order to achieve a given synthetic aperture sonar (SAS) beampattern specification, specified by the expected SAS array gain, is computed as a function of the number P of pings in the SAS. Higher accuracy is required when P increases to counter the accumulation of errors during the integration of the elementary ping-to-ping estimates: the standard deviation must decrease as P/sup -1/2/ for the DPCA sway and P/sup -3/2/ for the yaw. Finally, by combining the above results, the lower bounds on DPCA micronavigation accuracy are established. These bounds set an upper limit to the SAS length achievable in practice. The maximum gain Q in cross-range resolution achievable by a DPCA micronavigated SAS is computed as a function of the key SAS parameters. These theoretical predictions are compared with simulations and experimental results.     

Vertical stress distribution due to an arbitrarily shaped foundation using triangulation and an analytical expression for a triangular loaded region

Using the basic Boussinesq's equation, the expression for the vertical stress distribution (σ_z) underneath any point on the ground surface due to a general triangular loaded region in a preferred orientation with a linearly varied loading has been successfully derived. When the triangle is not in a preferred orientation, a simple axis transformation is required and the expression will be equally applicable. Based on this expression, σ_z due to an arbitrarily shaped loaded foundation can simply be determined by first triangulating the loaded area and summing up the contributions from each generated triangular region. The procedures for triangulating and calculating the stress distribution can be simply automated through computer programs.