Heat flow and mass wasting in the Wilmington Canyon Region: U.S. Continental Margin

The average corrected heat flow in the Wilmington Canyon region, an area of inferred slope instability, is 35 ± 10 mW/m². This average heat flow is marginally consistent with the 46 ± 9 mW/m² measured at other North Atlantic sites over 160 m.y. old. High topographic relief causes most of the variability in surface heat flow and may lower the mean surface heat flow. There is no significant difference between the average corrected heat flow of 35 ± 10 mW/m² in sediment slide areas and the average corrected heat flow of 34 ± 10 mW/m² in undisturbed sediments.     

Behavioural Effects of Chemically Dispersed Oil and Subsequent Recovery in Diploria strigosa (Dana)

Abstract. Survival and behaviour of the hermatypic coral Diploria strigosa was studied during 6–24 h doses with water-accomodated fractions of chemically dispersed crude oil, and for a subsequent recovery period of 1 month. Experiments utilized a flow-through laboratory dosing procedure and incorporated petroleum hydrocarbon measurements in order to simulate a major but short-term oil spill in shallow subtidal benthic reef environments. Chemically dispersed oil treatments consisted of Arabian Light Crude oil with Corexit 9527 or BP1100WD at 1–20 ppm concentrations of oil.
In general, effects observed were sub-lethal, temporary, and associated with the highest concentrations tested. Responses to the presence of dispersed oil at 20ppm for 24 h included mesenterial filament extrusion, extreme tissue contraction, tentacle retraction and localized tissue rupture. The nature and severity of reactions during the dosing phase varied between colonies and treatments, but colonies typically resumed normal behaviour within 2 h to 4 d of the recovery period. It therefore seems unlikely that observed biological effects would impair long-term viability.     

Long term prediction of non-linear vertical bending moments on a fast monohull

An assessment is made of the maximum wave induced bending moment expected to occur during the operational lifetime of a fast monohull, based on long term distribution calculations of the non-linear vertical bending moment at mid-ship. The ship is assumed to operate in the Northern North Sea, with an operational life of 25 years. A succession of short-term stationary ship responses represented by Rayleigh distributions of peaks results in the long-term distribution of the structural loads. Non-linear pseudo transfer functions are used in the procedure to calculate the variances of the short-term responses. The amplitudes of these transfer functions are calculated by a non-linear time domain seakeeping program. The results are compared with rules minimum required values and also with results from simpler calculation procedures such as adopting design sea states.     

An ocean bottom,microprocessor based seismometer

We describe the design and construction of an ocean bottom seismometer configured as a computer, based on an Intersil IM6100 microprocessor plus appropriate peripheral devices. The sensors consist of triaxial 1 Hz seismometers and a hydrophone, each sensor channel being filtered prior to digitizing so that typical noise spectra are whitened. Digital data are recorded serially on magnetic tape. The instrument is placed on the ocean bottom by allowing it to fall freely from just below the surface. An acoustic system allows precise determination of instrument position, acoustic recall, and transmission of operational information to the surface. Release from an expendable anchor is accomplished by redundant pyrotechnic bolts which can be fired by acoustic command or by precision timers.The operational flexibility provided by the micro-computer, which executes the DEC PDP8/E instruction set, enables optimum use of the 6-hr recording capacity (at 128 samples/second/channel) in the context of the particular experiment being performed.

---

     

Composition and Useful Properties of Tailings of Marine Manganese Nodules and Crusts

Marine manganese nodules and crusts, when processed, yield tailings which may be utilized for environmental and economic benefit. The key to the reasonable and effective utilization of these tailings lies in making a systematic appraisal of their composition and properties. This article gives an introduction to the investigation of manganese tailings properties. The tailings have a high iron and/or manganese content, high surface area, high porosity, and fine grain size. Some tailings have a high rare earth element content which is valuable. They may also have high SO₃, arsenic, and uranium contents which are harmful. Depending on the process used to produce the tailings, there will likely be some differences in chemical composition, mineral assemblages, surface area and adsorption capability, pore diameter and volume, density and pH. In assigning potentially beneficial applications for these tailings, these differences should be taken into account to optimize utilization.