Re-Suspension Technique for Improving Organic Rich Sediment-Water Quality in a Shallow Sea Area

The re-suspension method consists of (1) dispersion of the sediment by air-water jets, (2) pumping of the suspension (small particles and organic matter), (3) settlement in a tank, (4) filtration and (5) disposal of solids (followed by incineration in this case). The pilot test was performed to clean up an area of 3000 m². The dispersed depth of the bottom was approximately 50 cm. The time spent for the work was two weeks. The amount of re-suspended solid removed from the bottom was about 8 tonnes in dry mass. Since the solids contain high concentrations of chemical oxygen demand (COD), total phosphorous (T-P), total nitrogen (T-N) and sulfides, the remaining sediment was considerably improved. Quantitative analyses showed that the full-scale implementation would enable the removal of about 10% of the re-suspended solids, and reduce COD by 95%, T-P by 50%, T-N by 100% and sulfide by 75% for re-deposited sediments in comparison to the original sediments.     

Attenuation of compressional waves in peridotite measured as a function of temperature at 200 MPa

A technique has been developed to determine attenuation in rocks at high temperature using a gas-media, high-pressure apparatus. A pulse transmission technique and a spectral ratio method are used to study compressional seismic properties of rocks. Seismic waves are transmitted to and from the sample through buffer rods of mullite. The effect of seismic wave reflections within the sample assembly are cancelled out by taking ratios of the spectra measured at different temperatures. In order to obtain good signal-to-noise ratio for resolving the attenuation at high pressure and temperature, special care is taken in the sample assembly and the ultrasonic coupling between the sample, buffer rods and transducers. A very tight connection of the sample-buffer rod-transducer is essential for obtaining high frequency signals (>300 kHz) at high temperature. A small mass is attached to each outside end of the transducer to drive low frequency signals (<250 kHz) into the sample. Before attenuation measurements, the sample and the buffer rods are tightly compacted in a platinum tube at high pressure and room temperature to ensure pressure seal of the sample assembly. The frequency range of measurement covers 50 to 450 kHz for the sample. Attenuation is very small in the buffer rod compared to the sample for the entire temperature range of the study. Because of the small attenuation, a wide frequency band of 50 kHz to 3.2 MHz can be covered for investigating the attenuation in the buffer rod. The technique has been used to measure attenuation at high confining pressure, and temperatures including sub- and hyper-solidus of upper mantle rocks. Therefore, effects of partial melting on attenuation can be studied.The method is applied to the attenuation measurement in a peridotite as a function of temperature to 1225°C at 200 MPa confining pressure. At high temperature, signal amplitude decays more rapidly at high frequency than at low frequency, from which attenuation (andQ) can be determined using a spectral ratio method. No frequency dependence ofQ is resolved for both the sample and the buffer rod over the entire temperature and frequency ranges of the measurement. The results show thatQ decreases rapidly with increasing temperature even in the temperature range below the solidus of peridotites. Such temperature sensitivity ofQ is probably more useful to probe thermal structure in the upper mantle than that of conductivity at temperatures below the solidus. The results in this study are compared with available seismic velocity, electrical conductivity and solidus data for peridotites, suggesting that there is no discontinuous change in both mechanical and electrical properties of peridotites at the solidus temperature. Even at hypersolidus temperatures, it appears that velocity drops and conductivity increases continuously (not abruptly) with increasing melt fraction. This implies that mechanical and electrical properties of the upper mantle will gradually change at the boundary where the geotherm crosses the solidus.     

Lunar gravity field determination using SELENE same-beam differential VLBI tracking data

A lunar gravity field model up to degree and order 100 in spherical harmonics, named SGM100i, has been determined from SELENE and historical tracking data, with an emphasis on using same-beam S-band differential VLBI data obtained in the SELENE mission between January 2008 and February 2009. Orbit consistency throughout the entire mission period of SELENE as determined from orbit overlaps for the two sub-satellites of SELENE involved in the VLBI tracking improved consistently from several hundreds of metres to several tens of metres by including differential VLBI data. Through orbits that are better determined, the gravity field model is also improved by including these data. Orbit determination performance for the new model shows improvements over earlier 100th degree and order models, especially for edge-on orbits over the deep far side. Lunar Prospector orbit determination shows an improvement of orbit consistency from 1-day predictions for 2-day arcs of 6 m in a total sense, with most improvement in the along and cross-track directions. Data fit for the types and satellites involved is also improved. Formal errors for the lower degrees are smaller, and the new model also shows increased correlations with topography over the far side. The estimated value for the lunar GM for this model equals 4902.80080±0.0009 km³/s² (10 sigma). The lunar degree 2 potential Love number k ₂ was also estimated, and has a value of 0.0255 ± 0.0016 (10 sigma as well).     

Non‐linear system identification of the versatile‐typed structures by a novel signal processing technique

Non‐linear structural identification problems have raised considerable research efforts since decades, in which the Bouc–Wen model is generally utilized to simulate non‐linear structural constitutive characteristic. Support vector regression (SVR), a promising data processing method, is studied for versatile‐typed structural identification. First, a model selection strategy is utilized to determine the unknown power parameter of the Bouc–Wen model. Meanwhile, optimum SVR parameters are selected automatically, instead of tuning manually. Consequently, the non‐linear structural equation is rewritten in linear form, and is solved by the SVR technique. A five‐floor versatile‐type structure is studied to show the effectiveness of the proposed method, in which both power parameter known and unknown cases are investigated. Copyright © 2007 John Wiley & Sons, Ltd.     

大鹏湾潮流数值计算

应用分步杂交方法建立了大鹏湾边界潮流数值模型，并对其进行了模拟计算，重现了该区域潮波及潮流的分布规律，并根据实测资料对其进行了验证，从而可系统地了解这一海区的潮波系统及潮流场等海洋要素的分布情况。     

Long-term evolution of the aerosol debris cloud produced by the 2009 impact on Jupiter

We present a study of the long-term evolution of the cloud of aerosols produced in the atmosphere of Jupiter by the impact of an object on 19 July 2009 (Sánchez-Lavega, A. et al. [2010]. Astrophys. J. 715, L155-L159). The work is based on images obtained during 5 months from the impact to 31 December 2009 taken in visible continuum wavelengths and from 20 July 2009 to 28 May 2010 taken in near-infrared deep hydrogen-methane absorption bands at 2.1-2.3 μm. The impact cloud expanded zonally from ∼5000 km (July 19) to 225,000 km (29 October, about 180° in longitude), remaining meridionally localized within a latitude band from 53.5°S to 61.5°S planetographic latitude. During the first two months after its formation the site showed heterogeneous structure with 500-1000 km sized embedded spots. Later the reflectivity of the debris field became more homogeneous due to clump mergers. The cloud was mainly dispersed in longitude by the dominant zonal winds and their meridional shear, during the initial stages, localized motions may have been induced by thermal perturbation caused by the impact’s energy deposition. The tracking of individual spots within the impact cloud shows that the westward jet at 56.5°S latitude increases its eastward velocity with altitude above the tropopause by 5-10 m s⁻¹. The corresponding vertical wind shear is low, about 1 m s⁻¹ per scale height in agreement with previous thermal wind estimations. We found evidence for discrete localized meridional motions with speeds of 1-2 m s⁻¹. Two numerical models are used to simulate the observed cloud dispersion. One is a pure advection of the aerosols by the winds and their shears. The other uses the EPIC code, a nonlinear calculation of the evolution of the potential vorticity field generated by a heat pulse that simulates the impact. Both models reproduce the observed global structure of the cloud and the dominant zonal dispersion of the aerosols, but not the details of the cloud morphology. The reflectivity of the impact cloud decreased exponentially with a characteristic timescale of 15 days; we can explain this behavior with a radiative transfer model of the cloud optical depth coupled to an advection model of the cloud dispersion by the wind shears. The expected sedimentation time in the stratosphere (altitude levels 5-100 mbar) for the small aerosol particles forming the cloud is 45-200 days, thus aerosols were removed vertically over the long term following their zonal dispersion. No evidence of the cloud was detected 10 months after the impact.     

What motivates single women to migrate from northern Ghana to Accra?

In recent decades there has been a large migration stream of single women from the north to Accra in Ghana. Existing studies have focused on young migrant women’s livelihood strategies in their place of destination. However, once-married women – divorced and widowed women and neglected wives – also migrate, and their motivations for migration are less known. Drawing on qualitative and quantitative methods, the authors investigate the effects of gender norms, age, marital status, socio-economic status, and position in households on women’s decisions to migrate. The results revealed that migrant women from resource-poor households, regardless of age, marital status and position in households, commonly cited a gain in autonomy as an important motivation for their migration. From a differentiated perspective, young unmarried women aspired to prepare themselves for often expensive religious marriage ceremonies, whereas once-married women invest in their children’s education and build their own housing. By paying attention to the effects of gender norms, age, marital status, socio-economic status, and position in households on women’s decisions to migrate, the study illuminates the contradictory ways in which their migration practices are both shaped by and shape gender ideologies in parts of contemporary northern Ghana.     

Estimating the geostrophic velocity obtained by HF radar observations in the upstream area of the Kuroshio

A method to extract geostrophic current in the daily mean HF radar data in the Kuroshio upstream region is established by comparison with geostrophic velocity determined from the along-track altimetry data. The estimated Ekman current in the HF velocity is 1.2% (1.5%) and 48° (38°)-clockwise rotated with respect to the daily mean wind in (outside) the Kuroshio. Furthermore, additional temporal smoothing is found necessary to remove residual ageostrophic currents such as the inertial oscillation. After removal of the ageostrophic components, the HF geostrophic velocity agrees well with that from the altimetry data with rms difference 0.14 (0.12) m/s in (outside) the Kuroshio.     

A study of microearthquake seismicity and focal mechanisms within the Sea of Marmara (NW Turkey) using ocean bottom seismometers (OBSs)

We have carried out seismological observations within the Sea of Marmara (NW Turkey) in order to investigate the seismicity induced after Gölcük–İzmit (Kocaeli) earthquake (M_w 7.4) of August 17, 1999, using ocean bottom seismometers (OBSs). High-resolution hypocenters and focal mechanisms of microearthquakes have been investigated during this Marmara Sea OBS project involving deployment of 10 OBSs within the Çınarcık (eastern Marmara Sea) and Central-Tekirdağ (western Marmara Sea) basins during April–July 2000. Little was known about microearthquake activity and their source mechanisms in the Marmara Sea. We have detected numerous microearthquakes within the main basins of the Sea of Marmara along the imaged strands of the North Anatolian Fault (NAF). We obtained more than 350 well-constrained hypocenters and nine composite focal mechanisms during 70 days of observation. Microseismicity mainly occurred along the Main Marmara Fault (MMF) in the Marmara Sea. There are a few events along the Southern Shelf. Seismic activity along the Main Marmara Fault is quite high, and focal depth distribution was shallower than 20 km along the western part of this fault, and shallower than 15 km along its eastern part. From high-resolution relative relocation studies of some of the microearthquake clusters, we suggest that the western Main Marmara Fault is subvertical and the eastern Main Marmara Fault dips to south at 45°. Composite focal mechanisms show a strike-slip regime on the western Main Marmara Fault and complex faulting (strike-slip and normal faulting) on the eastern Main Marmara Fault.     

Full‐scale shaking table test of a base‐isolated medical facility subjected to vertical motions

Base isolation is a well known technology that has been proven to reduce structural response to horizontal ground accelerations. However, vertical response still remains a topic of concern for base‐isolated buildings, perhaps more so than in fixed‐base buildings as isolation is often used when high performance is required. To investigate the effects of vertical response on building contents and nonstructural components, a series of full‐scale shaking table tests were conducted at the E‐Defense facility in Japan. A four‐story base‐isolated reinforced concrete building was outfitted as a medical facility with a wide variety of contents, and the behavior of the contents was observed. The rubber base isolation system was found to significantly amplify vertical accelerations in some cases. However, the damage caused by the vertical ground motions was not detrimental when peak vertical floor accelerations remained below 2 g with three exceptions: (1) small items placed on shelves slid or toppled; (2) objects jumped when placed on nonrigid furniture, which tended to increase the response; and (3) equipment with vertical eccentricities rocked and jumped. In these tests, all equipment and nonstructural components remained functional after shaking. Copyright © 2013 John Wiley & Sons, Ltd.