Space weathered rims found on the surfaces of the Itokawa dust particles

On the basis of observations using Cs‐corrected STEM, we identified three types of surface modification probably formed by space weathering on the surfaces of Itokawa particles. They are (1) redeposition rims (2–3 nm), (2) composite rims (30–60 nm), and (3) composite vesicular rims (60–80 nm). These rims are characterized by a combination of three zones. Zone I occupies the outermost part of the surface modification, which contains elements that are not included in the unchanged substrate minerals, suggesting that this zone is composed of sputter deposits and/or impact vapor deposits originating from the surrounding minerals. Redeposition rims are composed only of Zone I and directly attaches to the unchanged minerals (Zone III). Zone I of composite and composite vesicular rims often contains nanophase (Fe,Mg)S. The composite rims and the composite vesicular rims have a two‐layered structure: a combination of Zone I and Zone II, below which Zone III exists. Zone II is the partially amorphized zone. Zone II of ferromagnesian silicates contains abundant nanophase Fe. Radiation‐induced segregation and in situ reduction are the most plausible mechanisms to form nanophase Fe in Zone II. Their lattice fringes indicate that they contain metallic iron, which probably causes the reddening of the reflectance spectra of Itokawa. Zone II of the composite vesicular rims contains vesicles. The vesicles in Zone II were probably formed by segregation of solar wind He implanted in this zone. The textures strongly suggest that solar wind irradiation damage and implantation are the major causes of surface modification and space weathering on Itokawa.     

Mineral chemistry of MUSES‐C Regio inferred from analysis of dust particles collected from the first‐ and second‐touchdown sites on asteroid Itokawa

The mineralogy and mineral chemistry of Itokawa dust particles captured during the first and second touchdowns on the MUSES‐C Regio were characterized by synchrotron‐radiation X‐ray diffraction and field‐emission electron microprobe analysis. Olivine and low‐ and high‐Ca pyroxene, plagioclase, and merrillite compositions of the first‐touchdown particles are similar to those of the second‐touchdown particles. The two touchdown sites are separated by approximately 100 meters and therefore the similarity suggests that MUSES‐C Regio is covered with dust particles of uniform mineral chemistry of LL chondrites. Quantitative compositional properties of 48 dust particles, including both first‐ and second‐touchdown samples, indicate that dust particles of MUSES‐C Regio have experienced prolonged thermal metamorphism, but they are not fully equilibrated in terms of chemical composition. This suggests that MUSES‐C particles were heated in a single asteroid at different temperatures. During slow cooling from a peak temperature of approximately 800 °C, chemical compositions of plagioclase and K‐feldspar seem to have been modified: Ab and Or contents changed during cooling, but An did not. This compositional modification is reproduced by a numerical simulation that modeled the cooling process of a 50 km sized Itokawa parent asteroid. After cooling, some particles have been heavily impacted and heated, which resulted in heterogeneous distributions of Na and K within plagioclase crystals. Impact‐induced chemical modification of plagioclase was verified by a comparison to a shock vein in the Kilabo LL6 ordinary chondrite where Na‐K distributions of plagioclase have been disturbed.     

Geometric Dependence of the Scalar Transfer Efficiency over Rough Surfaces

We performed a series of wind-tunnel experiments under neutral conditions in order to create a comprehensive database of scalar transfer coefficients for street surfaces using regular block arrays representing an urban environment. The objective is to clarify the geometric dependence of scalar transfer phenomena on rough surfaces. In addition, the datasets we have obtained are necessary to improve the modelling of scalar transfer used for computational simulations of urban environments; further, we can validate the results obtained by numerical simulations. We estimated the scalar transfer coefficients using the salinity method. The various configurations of the block arrays were designed to be similar to those used in a previous experiment to determine the total drag force acting on arrays. Our results are summarized as follows: first, the results for cubical arrays showed that the transfer coefficients for staggered and square layouts varied with the roughness packing density. The results for the staggered layout showed the possibility that the mixing effect of air can be enhanced for the mid-range values of the packing density. Secondly, the transfer coefficients for arrays with blocks of non-uniform heights were smaller than those for arrays with blocks of uniform height under conditions of low packing density; however, as the packing density increased, the opposite tendency was observed. Thirdly, the randomness of rotation angles of the blocks in the array led to increasing values of the transfer coefficients under sparse packing density conditions when compared with those for cubical arrays.     

Mineralogical and Geochemical Characteristics of the Utanobori Gold Deposit in Northern Hokkaido,Japan

The Utanobori gold deposit is a low‐sulfidation, epithermal vein‐type deposit located in northern Hokkaido, Japan. The deposit is hosted by conglomerate, sandstone, and tuff of the Middle to Late Miocene Esashi Formation. These rocks were hydrothermally altered. Silica sinters and quartz‐adularia veins are common in the deposit. The quartz‐adularia veins either contain a ginguro band, which corresponds to the main gold‐bearing vein (Type 1 Veins), or do not contain a ginguro band but contain minor adularia (Type 2 Veins). Type 1 Veins are divided into three stages with 12–14 substages. Ore minerals identified include electrum, naumannite, chlorargyrite, bromargyrite, an unidentified Fe‐Sb mineral, and an Fe‐(Sb)‐As mineral. These ore minerals formed in the main mineralization stages I (bands I‐b and I‐d) and II (band II‐a). Scanning electron microscopy with cathodoluminescence images show that cathodoluminescence‐dark microcrystalline quartz exhibiting colloform (ghost‐sphere) texture is closely associated with ore minerals in the Type 1 Vein and Type 2 Vein, and the Al and K contents of such quartz are commonly >1000 ppm. This indicates that the ore minerals were crystallized from alkaline, silica‐saturated fluids at temperatures <200°C, which initially deposited amorphous silica that was recrystallized to microcrystalline quartz. The average Au content of electrum is 52.5 at% Au (n = 10), 65.7 at% Au (n = 20), and 55.5 at% Au (n = 5) in bands I‐b, I‐d, and II‐a, respectively, of Type 1 Veins. The δ³⁴S_CDT values of two fine‐grained disseminated pyrites in the altered conglomerate and bedded tuff in the argillic altered zone are ?4.3 and ?4.2‰. Ar‐Ar dating on adularia yielded 13.6 ± 0.06 Ma, 13.6 ± 0.07 Ma, and 13.6 ± 0.06 Ma for the stages I, II, and III of the Type 1 Vein, respectively. K‐Ar ages determined on adularia in the silica sinter and on whole‐rock of glassy rhyolite of the Esashi Formation are 15.0 ± 0.4 Ma and 14.6 ± 0.4 Ma, respectively. These radiometric ages indicate that silica sinter associated with the rhyolitic volcanic rocks formed prior to the main gold mineralization.