Extraction and recovery of precious metals from electronic waste printed circuit boards by bioleaching acidophilic fungi

Printed circuit boards contain precious metals. They are produced in large volumes, rendering them an important component of the electronic waste. In view of the heterogeneity of the metals present, reprocessing of electronic waste is a heinous task. The present study focused on leaching of valuable metals from electronic waste printed circuit boards using Aspergillus niger DDNS1. The adaptation phases began at 0.1, 0.5 and 1.0% of fine powder of printed circuit boards with 10% inoculum and were optimized with three effective factors, viz. initial pH, particle size and pulp density, to achieve the maximum simultaneous recovery of the valuable metals. The interactions of these metals were also deciphered using scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, Fourier transform infrared spectrum and atomic absorption spectroscopy. The results indicated that extraction of the precious metals was accomplished mainly through the unique organic acids originating from A. niger DDNS1. The initial pH played an important role in the extraction of the precious metals and the metals precipitate formation. The leaching rate of the metals was generally higher at low powder dosage of printed circuit boards. The toxicity of the printed circuit boards had little effect on two-step bioleaching at the pulp density of 0.1% compared to one-step bioleaching. The two-step bioleaching process was followed under organic acid-forming conditions for the maximum mobilization of metals. Thus, the precious metals from printed circuit boards could be mobilized through fungal bioleaching which promises an important industrial application in recycling of electronic wastes.     

Petrology and geochemistry of Northwest Africa 5480 diogenite and evidence for a basin‐forming event on Vesta

We performed a petrological and geochemical study of an olivine diogenite, Northwest Africa (NWA) 5480. NWA 5480 is a crystalline stone, but shows a heterogeneous texture. Olivine aggregates and grains of olivine and chromite display resorption textures set in a crystalline pyroxene matrix. Large olivine aggregates are penetrated by pyroxene matrix. Flow textures are observed near olivine aggregates. Olivine, chromite, and pyroxene show minor chemical zoning, implying relatively rapid cooling. NWA 5480 contains a significant amount of platinum group elements with chondritic relative proportions. All this evidence supports that NWA 5480 is an impact‐melt breccia from a target composed of olivine and pyroxene‐rich lithologies. Such impact melt would have formed by melting crustal materials, possibly during one of the impacts that formed the South Pole basins on Vesta.     

Réflexions sur la contingence des lois de la Nature

There are two fundamental conceptions concerning the laws of nature — these laws are eternal or they may vary in the course of time. We suggest an experiment in order to find an intermediary thesis — i.e. to discover that law, if it really exists, according to which a given law of nature varies, or, at least, to find out the direction in which this variation is performed.     

A Spectrophotometric Study of the Be Star HD 164447

Spectra of the Be star HD 164447 have been studied. The equivalent widths and the intensities of the measured lines are given. No emission is apparent on the plates. Applying the thin layer theory some parameters of the stars atmosphere were derived.     

Directional dependence of P- and S-wave propagation and polarization in foliated rocks from the Kola superdeep well: Evidence from laboratory measurements and calculations based on TOF neutron diffraction

We have measured P- and S-wave velocities on two amphibolite and two gneiss samples from the Kola superdeep borehole as a function of pressure (up to 600 MPa) and temperature (up to 600 °C). The velocity measurements include compressional (Vp) and shear wave velocities (Vs1, Vs2) propagating in three orthogonal directions which were in general not parallel to inherent rock symmetry axes or planes. The measurements are accompanied by 3D-velocities calculations based on lattice preferred orientation (LPO) obtained by TOF (Time Of Flight) neutron diffraction analysis which allows the investigation of bulk volumes up to several cubic centimetres due to the high penetration depth of neutrons. The LPO-based numerical velocity calculations give important information on the different contribution of the various rock-forming minerals to bulk elastic anisotropy and on the relations of seismic anisotropy, shear wave splitting, and shear wave polarization to the structural reference frame (foliation and lineation). Comparison with measured velocities obtained for the three propagation directions that were not in accordance with the structural frame of the rocks (foliation and lineation) demonstrate that for shear waves propagating through anisotropic rocks the vibration directions are as important as the propagation directions. The study demonstrates that proper measurement of shear wave splitting by means of two orthogonal polarized sending and receiving shear wave transducers is only possible when their propagation and polarization directions are parallel and normal to foliation and lineation, respectively.     

Jet Deflection by a Quasi-Steady-State Side Wind in the Laboratory

We present experimental data on the steady state deflection of a highly supersonic jet by a side-wind in the laboratory. The use of a long interaction region enables internal shocks to fully cross the jet, leading to the development of significantly more structure in the jet than in previous work with a similar setup (Lebedev et al., 2004). The ability to control the length of the interaction region in the laboratory allows the switch between a regime representing a clumpy jet or wind and a regime similar to a slowly varying mass loss rate. The results indicate that multiple internal oblique shocks develop in the jet and the possible formation of a second working surface as the jet attempts to tunnel through the ambient medium.     

Improving efficiency in radio surveys for gravitational lenses

Many lens surveys have hitherto used observations of large samples of background sources to select the small minority which are multiply imaged by lensing galaxies along the line of sight. Recently surveys such as SLACS and OLS have improved the efficiency of surveys by pre-selecting double-redshift systems from SDSS. We explore other ways to improve survey efficiency by optimum use of astrometric and morphological information in existing large-scale optical and radio surveys. The method exploits the small position differences between FIRST radio positions of lensed images and the SDSS lens galaxy positions, together with the marginal resolution of some larger gravitational lens systems by the FIRST beam. We present results of a small pilot study with the VLA and MERLIN, and discuss the desirable criteria for future surveys.