Cross-Validation of Open-Path and Closed-Path Eddy-Covariance Techniques for Observing Methane Fluxes

Methane ( ${\mathrm {CH}}_{4}$ ) fluxes observed with the eddy-covariance technique using an open-path ${\mathrm {CH}}_{4}$ analyzer and a closed-path ${\mathrm {CH}}_{4}$ analyzer in a rice paddy field were evaluated with an emphasis on the flux correction methodology. A comparison of the fluxes obtained by the analyzers revealed that both the open-path and closed-path techniques were reliable, provided that appropriate corrections were applied. For the open-path approach, the influence of fluctuations in air density and the line shape variation in laser absorption spectroscopy (hereafter, spectroscopic effect) was significant, and the relative importance of these corrections would increase when observing small ${\mathrm {CH}}_{4}$ fluxes. A new procedure proposed by Li-Cor Inc. enabled us to accurately adjust for these effects. The high-frequency loss of the open-path ${\mathrm {CH}}_{4}$ analyzer was relatively large (11 % of the uncorrected covariance) at an observation height of 2.5 m above the canopy owing to its longer physical path length, and this correction should be carefully applied before correcting for the influence of fluctuations in air density and the spectroscopic effect. Uncorrected ${\mathrm {CH}}_{4}$ fluxes observed with the closed-path analyzer were substantially underestimated (37 %) due to high-frequency loss because an undersized pump was used in the observation. Both the bandpass and transfer function approaches successfully corrected this flux loss. Careful determination of the bandpass frequency range or the transfer function and the cospectral model is required for the accurate calculation of ${\mathrm {CH}}_{4}$ fluxes with the closed-path technique.     

Middle Eocene low-paleolatitude radiolarian evidence for the Cabog Formation,Central East Luzon,Philippine Mobile Belt

The Cabog Formation, newly established herein and exposed in central East Luzon, Philippine Mobile Belt, is defined in age by the occurrence of radiolarians. The radiolarian assemblage is correlative with the middle Eocene and suggests a low paleolatitude affinity. The correlation, sedimentary environment, and the tectonic significance are discussed. The Cabog Formation is correlative with the distal part of the middle–late Eocene Caraballo Formation, which is exposed in the northeastern side of the Philippine Fault Zone. The sandstone composition and radiolarian age suggest that the Cabog Formation represents the first depositional stage in the early arc setting. The northward migration of the formation is also estimated in relation with the Philippine Sea Plate motion along the Older Philippine Fault from the equatorial area.     

Hayabusa‐returned sample curation in the Planetary Material Sample Curation Facility of JAXA

Abstract– The Planetary Material Sample Curation Facility of JAXA (PMSCF/JAXA) was established in Sagamihara, Kanagawa, Japan, to curate planetary material samples returned from space in conditions of minimum terrestrial contaminants. The performances for the curation of Hayabusa‐returned samples had been checked with a series of comprehensive tests and rehearsals. After the Hayabusa spacecraft had accomplished a round‐trip flight to asteroid 25143 Itokawa and returned its reentry capsule to the Earth in June 2010, the reentry capsule was brought back to the PMSCF/JAXA and was put to a series of processes to extract recovered samples from Itokawa. The particles recovered from the sample catcher were analyzed by electron microscope, given their ID, grouped into four categories, and preserved in dimples on quartz slide glasses. Some fraction of them has been distributed for initial analyses at NASA, and will be distributed for international announcement of opportunity (AO), but a certain fraction of them will be preserved in vacuum for future analyses.     

Investigation of cutting methods for small samples of Hayabusa and future sample return missions

We report the investigation of cutting methods for Hayabusa samples. The purpose of our study is to explore the possibility of applying multiple analyses to a single particle effectively. We investigated the cutting performance of a blade dicing saw, laser, focused ion beam (FIB), and physical breaking by microindenter. Cutting performance was examined by estimating the aspect ratio of the cut slit, i.e., depth over width of the slit. We also investigated the possible contamination and sample damage by cutting. The result of the investigation shows that we can cut the samples from <50 μm to 500 μm using those methods with aspect ratios from 10 to 20, although they would introduce some contamination or damage to the samples. Our investigations also provide an important basis for the analysis of samples obtained by future sample return missions.     

Sticking in moderate velocity oblique impact: Application to planetology

The sticking behavior of metal—metal collisions in the velocity range ～50–650 m/sec—has been investigated experimentally. A map of sticking efficiency versus impact angle and impact velocity has been established for lead. The threshold sticking velocity for normal impact equals approximately 100 m/sec for lead, 140 m/sec for tin, and 500 m/sec for iron in the case of spherical projectiles of 8-mm diameter, and a semi-infinite target. The boundary between the plastic rebound area and the perfect sticking area is found to be a line of constant normal velocity. The case when projectile mass is equal to target. ass ($\text{?3}\text{g}$, lead) has been investigated as well. The experimental results have been extrapolated to higher temperature and then applied to iron, nickel, and magnesium silicate. Near the melting point ($\text{?1800°}\text{K}$), the sticking velocities were estimated as 250–350 m/sec for iron and nickel and about 40% higher for magnesium silicate. It was concluded that metals stick more easily than rocky materials because of their lower sticking velocity and much larger interval of temperature over which sticking is possible.     

Recovery of entire shocked samples in a range of pressure from ~100 GPa to Hugoniot elastic limit

We carried out laser shock experiments and wholly recovered shocked olivine and quartz samples. We investigated the petrographic features based on optical micrographs of sliced samples and found that each recovered sample comprises three regions, I (optically dark), II (opaque), and III (transparent). Scanning electron microscopy combined with electron backscattered diffraction shows that there are no crystal features in the region I; the materials in the region I have once melted. Moreover, numerical calculations performed with the iSALE shock physics code suggest that the boundary between regions II and III corresponds to Hugoniot elastic limit (HEL). Thus, we succeeded in the recovery of the entire shocked samples experienced over a wide range of pressures from HEL (~10 GPa) to melting pressure (~100 GPa) in a hierarchical order.     

Noble gases in individual chondrules of the Allende CV3 chondrite

We analyzed noble gases in nine individual chondrules, an assemblage of small chondrules, and four whole‐rock samples of the Allende CV3 chondrite. Major elements were also determined for five chondrules. The cosmic ray exposure ages are calculated from cosmogenic ³He to be 5.17 ± 0.38 and 5.15 ± 0.25 Myr for the averages of the chondrules and whole rocks, respectively, showing no significant pre‐exposure evidence for the studied chondrules. Large amounts of ³⁶Ar, ^80,82Kr, and ¹²⁸Xe produced by neutron capture are observed in most samples; the abundances of these nuclides are correlated among the samples. The epithermal neutron flux and neutron slowing down density are calculated based on [⁸⁰Kr]_n, from which a sample depth of about 30 cm can be calculated. The measured chondrules contain variable amounts of radiogenic ¹²⁹Xe. The abundance ratios of radiogenic ¹²⁹Xe to neutron capture–produced ¹²⁸Xe are rather constant among the studied chondrules; four chondrules give more precise ratios at the high‐temperature fractions, ranging from 1920 ± 80 to 2280 ± 140, which corresponds to a time difference of 3.9 ± 2.4 Myr. It is noticeable that most chondrules also contain ²⁴⁴Pu‐derived fission Xe. The average ²⁴⁴Pu/²³⁸U ratio for nine chondrules is 0.0069 ± 0.0018, which agrees well with the preferred ratio reported for chondrites.     

Forecasting Hourly Roadside Particulate Matter in Taipei County of Taiwan Based on First‐Order and One‐Variable Grey Model

In this study, seven types of first‐order and one‐variable grey differential equation model (abbreviated as GM (1, 1) model) were used to forecast hourly roadside particulate matter (PM) including PM₁₀ and PM_2.5 concentrations in Taipei County of Taiwan. Their forecasting performance was also compared. The results indicated that the minimum mean absolute percentage error (MAPE), mean squared error (MSE), root mean squared error (RMSE), and maximum correlation coefficient (R) was 11.70%, 60.06, 7.75, and 0.90%, respectively when forecasting PM₁₀. When forecasting PM_2.5, the minimum MAPE, MSE, RMSE, and maximum R‐value of 16.33%, 29.78, 5.46, and 0.90, respectively could be achieved. All statistical values revealed that the forecasting performance of GM (1, 1, x⁽⁰⁾), GM (1, 1, a), and GM (1, 1, b) outperformed other GM (1, 1) models. According to the results, it revealed that GM (1, 1) was an efficiently early warning tool for providing PM information to the roadside inhabitants.