Fluid permeability of sedimentary rocks in a complete stress–strain process

The permeability of sedimentary rocks during triaxial compression tests was investigated to relate it to the complete strain–stress process. It was found that the permeability was not constant, but varied with the stress and strain states in the rocks. Prior to the peak strength, the permeability decreases with increasing load. A dramatic increase in permeability occurs during the strain softening period. In the present study, in situ measurements of fluid flow and pressure in floor strata was carried out in a double longwall mining face in the Yangzhuang colliery. These measurements show that both the strata pressure and the position with respect to the mining face influence the hydrogeologic properties. The permeability increased in the floor strata behind the mining face because those mining induced fractures opened as the strata pressure decreased. To better understand this change in hydraulic behavior around the mining faces, 3-D numerical modeling was carried out. The model provides the general picture of the stress distribution and failure zone both in the floor and roof strata. The field and model results demonstrate the importance of changes in the stress and strain states on the hydrogeology of a site.     

Determining Q of near-surface materials from Rayleigh waves

High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (V_S), compressional (P)-wave velocity (V_P), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor Q_P and S-wave quality factor Q_S in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting Q_S from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from Q_P cannot be ignored when Vs/V_P reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert Q_P from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to Q_P than to Q_S. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.     

Monsoonal precipitation variation in the East Asia since A.D. 1840 ——Tree-ring evidences from China and Korea

The main characteristic of the East Asian climate is the monsoon system. Plenty of studies have demonstrated that the Asian monsoon system plays a crucial role in the global climate sys- tem [1-4]. The Asian summer monsoon can be divided into two parts, t…     

P-SH conversions in a flat-layered medium with anisotropy of arbitrary orientation

P-SH conversion is commonly observed in teleseismic P waves, and is often attributed to dipping interfaces beneath the receiver. Our modelling suggests an alternative explanation in terms of flat-layered anisotropy. We use reflectivity techniques to compute three-component synthetic seismograms in a 1-D anisotropic layered medium. For each layer of the medium, we prescribe values of seismic velocities and hexagonally symmetric anisotropy about a common symmetry axis of arbitrary orientation. A compressional wave in an anisotropic velocity structure suffers conversion to both SV -and SH -polarized shear waves, unless the axis of symmetry is everywhere vertical or the wave travels parallel to all symmetry axes. The P-SV conversion forms the basis of the widely used 'receiver function' technique. The P-SH conversion occurs at interfaces where one or both layers are anisotropic. A tilted axis of symmetry and a dipping interface in isotropic media produce similar amplitudes of both direct ( P ) and converted ( Ps ) phases, leaving the backazimuth variation of the P-Ps delay as the main discriminant. Seismic anisotropy with a tilted symmetry axis leads to complex synthetic seismograms in velocity models composed of just a few flat homogeneous layers. It is possible therefore to model observations of P coda with prominent transverse components with relatively simple 1-D velocity structures. Successful retrieval of salient model characteristics appears possible using multiple realizations of a genetic-algorithm (GA) inversion of P coda from several backazimuths. Using GA inversion, we determine that six P coda recorded at station ARU in central Russia are consistent with models that possess strong (> 10 per cent) anisotropy in the top 5 km and between 30 and 43 km depth. The symmetry axes are tilted, and appear aligned with the seismic anisotropy orientation in the mantle under ARU suggested by SKS splitting.     

Determination and application of the weights for landslide susceptibility mapping using an artificial neural network

The purpose of this study is the development, application, and assessment of probability and artificial neural network methods for assessing landslide susceptibility in a chosen study area. As the basic analysis tool, a Geographic Information System (GIS) was used for spatial data management and manipulation. Landslide locations and landslide-related factors such as slope, curvature, soil texture, soil drainage, effective thickness, wood type, and wood diameter were used for analyzing landslide susceptibility. A probability method was used for calculating the rating of the relative importance of each factor class to landslide occurrence. For calculating the weight of the relative importance of each factor to landslide occurrence, an artificial neural network method was developed. Using these methods, the landslide susceptibility index (LSI) was calculated using the rating and weight, and a landslide susceptibility map was produced using the index. The results of the landslide susceptibility analysis, with and without weights, were confirmed from comparison with the landslide location data. The comparison result with weighting was better than the results without weighting. The calculated weight and rating can be used to landslide susceptibility mapping.     

Probabilistic approach for active control of structures: experimental verification

In our previous study (Earthquake Engineering and Structural Dynamics 2003; 32 :2301), we have developed a probabilistic algorithm for active control of structures. In the probabilistic control algorithm, the control force is determined by the probability that the structural energy exceeds a specified target critical energy, and the direction of a control force is determined by the Lyapunov controller design method. In this paper, an experimental verification of the proposed probabilistic control algorithm is presented. A three‐story test structure equipped with an active mass driver (AMD) has been used. The effectiveness of the control algorithm has been examined by exciting the test structure using a sinusoidal signal, a scaled El Centro earthquake and a broadband Gaussian white noise; and, especially, experiments on control have been performed under different conditions to that of system identification in order to prove the stability and robustness of the proposed control algorithm. The experimental results indicate that the probabilistic control algorithm can achieve a significant response reduction under various types of ground excitations even when the modeling error exists. Copyright © 2004 John Wiley & Sons, Ltd.     

Polygonal grain‐based distinct element modeling for mechanical behavior of brittle rock

The microstructure of rock was numerically reproduced by a polygonal grain‐based model, and its mechanical behavior was examined by performing the uniaxial compression test and Brazilian tests via the Universal Distinct Element Code. The numerical results of the model demonstrated good agreement with the experimental results obtained with rock specimens in terms of the stress–strain behavior, strength characteristics, and brittle fracture phenomenon. An encouraging result is that the grain‐based model‐Universal Distinct Element Code model can reproduce a low ratio of tensile to compressive strength of 1/20 to 1/10 without the need for an additional process. This finding is ascribed to the fact that the geometrical features of polygons can effectively capture the effects of angularity, finite rotation, and interlocking of grains that exist in reality. A numerical methodology to monitor the evolution of micro‐cracks was developed, which enabled us to examine the progressive process of the failure and distinguish the contribution of tensile cracking to the process from that of shear cracking. From the observations of the micro‐cracking process in reference to the stress–strain relation, crack initiation stress, and crack damage stress, it can be concluded that the failure process of the model closely resembles the microscopic observations of rock. We also carried out a parametric study to examine the relationships between the microscopic properties and the macroscopic behavior of the model. Depending on the micro‐properties, the model exhibited a variety of responses to the external load in terms of the strength and deformation characteristics, the evolution of micro‐cracks, and the post‐peak behavior. Copyright © 2016 John Wiley & Sons, Ltd.     

Submarine groundwater discharge revealed by aerial thermal infrared imagery: a case study on Jeju Island,Korea

Submarine groundwater discharge (SGD) is a global phenomenon that carries large volumes of groundwater and dissolved chemical species such as nutrient, metals, and organic compounds to coastal zones. We report the influence of SGD on the coastal waters of Jeju Island, Korea, using high‐resolution aerial thermal infrared (TIR) mapping techniques and field investigations. An aircraft‐based system was implemented using a cost‐effective TIR camera for aerial TIR mapping. Ground‐based calibrations and system integration with GPS/IMU (global positioning system/inertial measurement unit) were performed for the aerial systems. The aerial surveys showed distinct low‐temperature signatures of SGD along the coasts of Jeju Island, revealing large groundwater inputs from the coastal aquifers to the ocean. Multiple aerial surveys over a range of seasons and tidal stages revealed that SGD rates dynamically affect the sea surface temperature (SST) of the coastal zone. The in‐situ measurements supported that SGD has a substantial influence on the coastal water chemistry as well as SST. Our observations highlight the extent to which aerial‐based TIR mapping can serve as a powerful tool for studying SGD and other coastal processes. Copyright © 2016 John Wiley & Sons, Ltd.